1 /* 2 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. 3 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_MPC8308_P1M 1 /* mpc8308_p1m board specific */ 20 21 #ifndef CONFIG_SYS_TEXT_BASE 22 #define CONFIG_SYS_TEXT_BASE 0xFC000000 23 #endif 24 25 /* 26 * On-board devices 27 * 28 * TSECs 29 */ 30 #define CONFIG_TSEC1 31 #define CONFIG_TSEC2 32 33 /* 34 * System Clock Setup 35 */ 36 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 37 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 38 39 /* 40 * Hardware Reset Configuration Word 41 * if CLKIN is 66.66MHz, then 42 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 43 * We choose the A type silicon as default, so the core is 400Mhz. 44 */ 45 #define CONFIG_SYS_HRCW_LOW (\ 46 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 47 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 48 HRCWL_SVCOD_DIV_2 |\ 49 HRCWL_CSB_TO_CLKIN_4X1 |\ 50 HRCWL_CORE_TO_CSB_3X1) 51 /* 52 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 53 * in 8308's HRCWH according to the manual, but original Freescale's 54 * code has them and I've expirienced some problems using the board 55 * with BDI3000 attached when I've tried to set these bits to zero 56 * (UART doesn't work after the 'reset run' command). 57 */ 58 #define CONFIG_SYS_HRCW_HIGH (\ 59 HRCWH_PCI_HOST |\ 60 HRCWH_PCI1_ARBITER_ENABLE |\ 61 HRCWH_CORE_ENABLE |\ 62 HRCWH_FROM_0X00000100 |\ 63 HRCWH_BOOTSEQ_DISABLE |\ 64 HRCWH_SW_WATCHDOG_DISABLE |\ 65 HRCWH_ROM_LOC_LOCAL_16BIT |\ 66 HRCWH_RL_EXT_LEGACY |\ 67 HRCWH_TSEC1M_IN_MII |\ 68 HRCWH_TSEC2M_IN_MII |\ 69 HRCWH_BIG_ENDIAN) 70 71 /* 72 * System IO Config 73 */ 74 #define CONFIG_SYS_SICRH (\ 75 SICRH_ESDHC_A_GPIO |\ 76 SICRH_ESDHC_B_GPIO |\ 77 SICRH_ESDHC_C_GTM |\ 78 SICRH_GPIO_A_TSEC2 |\ 79 SICRH_GPIO_B_TSEC2_TX_CLK |\ 80 SICRH_IEEE1588_A_GPIO |\ 81 SICRH_USB |\ 82 SICRH_GTM_GPIO |\ 83 SICRH_IEEE1588_B_GPIO |\ 84 SICRH_ETSEC2_CRS |\ 85 SICRH_GPIOSEL_1 |\ 86 SICRH_TMROBI_V3P3 |\ 87 SICRH_TSOBI1_V3P3 |\ 88 SICRH_TSOBI2_V3P3) /* 0xf577d100 */ 89 #define CONFIG_SYS_SICRL (\ 90 SICRL_SPI_PF0 |\ 91 SICRL_UART_PF0 |\ 92 SICRL_IRQ_PF0 |\ 93 SICRL_I2C2_PF0 |\ 94 SICRL_ETSEC1_TX_CLK) /* 0x00000000 */ 95 96 #define CONFIG_SYS_GPIO1_PRELIM 97 /* GPIO Default input/output settings */ 98 #define CONFIG_SYS_GPIO1_DIR 0x7AAF8C00 99 /* 100 * Default GPIO values: 101 * LED#1 enabled; WLAN enabled; Both COM LED on (orange) 102 */ 103 #define CONFIG_SYS_GPIO1_DAT 0x08008C00 104 105 /* 106 * IMMR new address 107 */ 108 #define CONFIG_SYS_IMMR 0xE0000000 109 110 /* 111 * SERDES 112 */ 113 #define CONFIG_FSL_SERDES 114 #define CONFIG_FSL_SERDES1 0xe3000 115 116 /* 117 * Arbiter Setup 118 */ 119 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 120 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 121 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 122 123 /* 124 * DDR Setup 125 */ 126 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 127 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 128 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 129 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 130 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 131 | DDRCDR_PZ_LOZ \ 132 | DDRCDR_NZ_LOZ \ 133 | DDRCDR_ODT \ 134 | DDRCDR_Q_DRN) 135 /* 0x7b880001 */ 136 /* 137 * Manually set up DDR parameters 138 * consist of two chips HY5PS12621BFP-C4 from HYNIX 139 */ 140 141 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 142 143 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 144 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 145 | CSCONFIG_ODT_RD_NEVER \ 146 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 147 | CSCONFIG_ROW_BIT_13 \ 148 | CSCONFIG_COL_BIT_10) 149 /* 0x80010102 */ 150 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 151 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 152 | (0 << TIMING_CFG0_WRT_SHIFT) \ 153 | (0 << TIMING_CFG0_RRT_SHIFT) \ 154 | (0 << TIMING_CFG0_WWT_SHIFT) \ 155 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 156 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 157 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 158 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 159 /* 0x00220802 */ 160 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 161 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 162 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 163 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 164 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 165 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 166 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 167 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 168 /* 0x27256222 */ 169 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 170 | (4 << TIMING_CFG2_CPO_SHIFT) \ 171 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 172 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 173 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 174 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 175 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 176 /* 0x121048c5 */ 177 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 178 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 179 /* 0x03600100 */ 180 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 181 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 182 | SDRAM_CFG_DBW_32) 183 /* 0x43080000 */ 184 185 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 186 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 187 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 188 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 189 #define CONFIG_SYS_DDR_MODE2 0x00000000 190 191 /* 192 * Memory test 193 */ 194 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 195 #define CONFIG_SYS_MEMTEST_END 0x07f00000 196 197 /* 198 * The reserved memory 199 */ 200 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 201 202 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 203 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 204 205 /* 206 * Initial RAM Base Address Setup 207 */ 208 #define CONFIG_SYS_INIT_RAM_LOCK 1 209 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 210 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 211 #define CONFIG_SYS_GBL_DATA_OFFSET \ 212 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 213 214 /* 215 * Local Bus Configuration & Clock Setup 216 */ 217 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 218 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 219 #define CONFIG_SYS_LBC_LBCR 0x00040000 220 221 /* 222 * FLASH on the Local Bus 223 */ 224 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 225 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 226 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 227 228 #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* FLASH base address */ 229 #define CONFIG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */ 230 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 231 232 /* Window base at flash base */ 233 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 234 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 235 236 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 237 | BR_PS_16 /* 16 bit port */ \ 238 | BR_MS_GPCM /* MSEL = GPCM */ \ 239 | BR_V) /* valid */ 240 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 241 | OR_UPM_XAM \ 242 | OR_GPCM_CSNT \ 243 | OR_GPCM_ACS_DIV2 \ 244 | OR_GPCM_XACS \ 245 | OR_GPCM_SCY_4 \ 246 | OR_GPCM_TRLX_SET \ 247 | OR_GPCM_EHTR_SET) 248 249 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 250 #define CONFIG_SYS_MAX_FLASH_SECT 512 251 252 /* Flash Erase Timeout (ms) */ 253 #define CONFIG_SYS_FLASH_ERASE_TOUT (1000 * 1024) 254 /* Flash Write Timeout (ms) */ 255 #define CONFIG_SYS_FLASH_WRITE_TOUT (500 * 1024) 256 257 /* 258 * SJA1000 CAN controller on Local Bus 259 */ 260 #define CONFIG_SYS_SJA1000_BASE 0xFBFF0000 261 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_SJA1000_BASE \ 262 | BR_PS_8 /* 8 bit port size */ \ 263 | BR_MS_GPCM /* MSEL = GPCM */ \ 264 | BR_V) /* valid */ 265 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 266 | OR_GPCM_SCY_5 \ 267 | OR_GPCM_EHTR_SET) 268 /* 0xFFFF8052 */ 269 270 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_SJA1000_BASE 271 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 272 273 /* 274 * CPLD on Local Bus 275 */ 276 #define CONFIG_SYS_CPLD_BASE 0xFBFF8000 277 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_CPLD_BASE \ 278 | BR_PS_8 /* 8 bit port */ \ 279 | BR_MS_GPCM /* MSEL = GPCM */ \ 280 | BR_V) /* valid */ 281 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB \ 282 | OR_GPCM_SCY_4 \ 283 | OR_GPCM_EHTR_SET) 284 /* 0xFFFF8042 */ 285 286 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_CPLD_BASE 287 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 288 289 /* 290 * Serial Port 291 */ 292 #define CONFIG_CONS_INDEX 1 293 #undef CONFIG_SERIAL_SOFTWARE_FIFO 294 #define CONFIG_SYS_NS16550 295 #define CONFIG_SYS_NS16550_SERIAL 296 #define CONFIG_SYS_NS16550_REG_SIZE 1 297 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 298 299 #define CONFIG_SYS_BAUDRATE_TABLE \ 300 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 301 302 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 303 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 304 305 /* Use the HUSH parser */ 306 #define CONFIG_SYS_HUSH_PARSER 307 308 /* Pass open firmware flat tree */ 309 #define CONFIG_OF_LIBFDT 1 310 #define CONFIG_OF_BOARD_SETUP 1 311 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 312 313 /* I2C */ 314 #define CONFIG_SYS_I2C 315 #define CONFIG_SYS_I2C_FSL 316 #define CONFIG_SYS_FSL_I2C_SPEED 400000 317 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 318 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 319 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 320 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 321 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 322 323 /* 324 * General PCI 325 * Addresses are mapped 1-1. 326 */ 327 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 328 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 329 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 330 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 331 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 332 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 333 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 334 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 335 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 336 337 /* enable PCIE clock */ 338 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 339 340 #define CONFIG_PCI 341 #define CONFIG_PCI_INDIRECT_BRIDGE 342 #define CONFIG_PCIE 343 344 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 345 346 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 347 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 348 349 /* 350 * TSEC 351 */ 352 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 353 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 354 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 355 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 356 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 357 358 /* 359 * TSEC ethernet configuration 360 */ 361 #define CONFIG_MII 1 /* MII PHY management */ 362 #define CONFIG_TSEC1_NAME "eTSEC0" 363 #define CONFIG_TSEC2_NAME "eTSEC1" 364 #define TSEC1_PHY_ADDR 1 365 #define TSEC2_PHY_ADDR 2 366 #define TSEC1_PHYIDX 0 367 #define TSEC2_PHYIDX 0 368 #define TSEC1_FLAGS 0 369 #define TSEC2_FLAGS 0 370 371 /* Options are: eTSEC[0-1] */ 372 #define CONFIG_ETHPRIME "eTSEC0" 373 374 /* 375 * Environment 376 */ 377 #define CONFIG_ENV_IS_IN_FLASH 1 378 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 379 CONFIG_SYS_MONITOR_LEN) 380 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 381 #define CONFIG_ENV_SIZE 0x2000 382 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 383 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 384 385 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 386 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 387 388 /* 389 * BOOTP options 390 */ 391 #define CONFIG_BOOTP_BOOTFILESIZE 392 #define CONFIG_BOOTP_BOOTPATH 393 #define CONFIG_BOOTP_GATEWAY 394 #define CONFIG_BOOTP_HOSTNAME 395 396 /* 397 * Command line configuration. 398 */ 399 #include <config_cmd_default.h> 400 401 #define CONFIG_CMD_DHCP 402 #define CONFIG_CMD_I2C 403 #define CONFIG_CMD_MII 404 #define CONFIG_CMD_NET 405 #define CONFIG_CMD_PCI 406 #define CONFIG_CMD_PING 407 408 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 409 410 /* 411 * Miscellaneous configurable options 412 */ 413 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 414 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 415 416 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 417 418 /* Print Buffer Size */ 419 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 420 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 421 /* Boot Argument Buffer Size */ 422 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 423 424 /* 425 * For booting Linux, the board info and command line data 426 * have to be in the first 8 MB of memory, since this is 427 * the maximum mapped by the Linux kernel during initialization. 428 */ 429 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 430 431 /* 432 * Core HID Setup 433 */ 434 #define CONFIG_SYS_HID0_INIT 0x000000000 435 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 436 HID0_ENABLE_INSTRUCTION_CACHE | \ 437 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 438 #define CONFIG_SYS_HID2 HID2_HBE 439 440 /* 441 * MMU Setup 442 */ 443 444 /* DDR: cache cacheable */ 445 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 446 BATL_MEMCOHERENCE) 447 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 448 BATU_VS | BATU_VP) 449 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 450 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 451 452 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 453 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 454 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 455 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 456 BATU_VP) 457 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 458 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 459 460 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 461 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 462 BATL_MEMCOHERENCE) 463 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 464 BATU_VS | BATU_VP) 465 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 466 BATL_CACHEINHIBIT | \ 467 BATL_GUARDEDSTORAGE) 468 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 469 470 /* Stack in dcache: cacheable, no memory coherence */ 471 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 472 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 473 BATU_VS | BATU_VP) 474 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 475 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 476 477 /* 478 * Environment Configuration 479 */ 480 481 #define CONFIG_ENV_OVERWRITE 482 483 #if defined(CONFIG_TSEC_ENET) 484 #define CONFIG_HAS_ETH0 485 #define CONFIG_HAS_ETH1 486 #endif 487 488 #define CONFIG_BAUDRATE 115200 489 490 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 491 492 #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ 493 494 #define CONFIG_EXTRA_ENV_SETTINGS \ 495 "netdev=eth0\0" \ 496 "consoledev=ttyS0\0" \ 497 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 498 "nfsroot=${serverip}:${rootpath}\0" \ 499 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 500 "addip=setenv bootargs ${bootargs} " \ 501 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 502 ":${hostname}:${netdev}:off panic=1\0" \ 503 "addtty=setenv bootargs ${bootargs}" \ 504 " console=${consoledev},${baudrate}\0" \ 505 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 506 "addmisc=setenv bootargs ${bootargs}\0" \ 507 "kernel_addr=FC0A0000\0" \ 508 "fdt_addr=FC2A0000\0" \ 509 "ramdisk_addr=FC2C0000\0" \ 510 "u-boot=mpc8308_p1m/u-boot.bin\0" \ 511 "kernel_addr_r=1000000\0" \ 512 "fdt_addr_r=C00000\0" \ 513 "hostname=mpc8308_p1m\0" \ 514 "bootfile=mpc8308_p1m/uImage\0" \ 515 "fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0" \ 516 "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ 517 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 518 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 519 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 520 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 521 "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ 522 "tftp ${fdt_addr_r} ${fdtfile};" \ 523 "run nfsargs addip addtty addmtd addmisc;" \ 524 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 525 "bootcmd=run flash_self\0" \ 526 "load=tftp ${loadaddr} ${u-boot}\0" \ 527 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 528 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 529 " +${filesize};cp.b ${fileaddr} " \ 530 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 531 "upd=run load update\0" \ 532 533 #endif /* __CONFIG_H */ 534