1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
4  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
5  *
6  */
7 
8 #ifndef __CONFIG_H
9 #define __CONFIG_H
10 
11 /*
12  * High Level Configuration Options
13  */
14 #define CONFIG_E300		1 /* E300 family */
15 #define CONFIG_MPC830x		1 /* MPC830x family */
16 #define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
17 
18 /*
19  * On-board devices
20  *
21  * TSECs
22  */
23 #define CONFIG_TSEC1
24 #define CONFIG_TSEC2
25 
26 /*
27  * System Clock Setup
28  */
29 #define CONFIG_83XX_CLKIN	33333333 /* in Hz */
30 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
31 
32 /*
33  * Hardware Reset Configuration Word
34  * if CLKIN is 66.66MHz, then
35  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
36  * We choose the A type silicon as default, so the core is 400Mhz.
37  */
38 #define CONFIG_SYS_HRCW_LOW (\
39 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
40 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
41 	HRCWL_SVCOD_DIV_2 |\
42 	HRCWL_CSB_TO_CLKIN_4X1 |\
43 	HRCWL_CORE_TO_CSB_3X1)
44 /*
45  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
46  * in 8308's HRCWH according to the manual, but original Freescale's
47  * code has them and I've expirienced some problems using the board
48  * with BDI3000 attached when I've tried to set these bits to zero
49  * (UART doesn't work after the 'reset run' command).
50  */
51 #define CONFIG_SYS_HRCW_HIGH (\
52 	HRCWH_PCI_HOST |\
53 	HRCWH_PCI1_ARBITER_ENABLE |\
54 	HRCWH_CORE_ENABLE |\
55 	HRCWH_FROM_0X00000100 |\
56 	HRCWH_BOOTSEQ_DISABLE |\
57 	HRCWH_SW_WATCHDOG_DISABLE |\
58 	HRCWH_ROM_LOC_LOCAL_16BIT |\
59 	HRCWH_RL_EXT_LEGACY |\
60 	HRCWH_TSEC1M_IN_MII |\
61 	HRCWH_TSEC2M_IN_MII |\
62 	HRCWH_BIG_ENDIAN)
63 
64 /*
65  * System IO Config
66  */
67 #define CONFIG_SYS_SICRH (\
68 	SICRH_ESDHC_A_GPIO |\
69 	SICRH_ESDHC_B_GPIO |\
70 	SICRH_ESDHC_C_GTM |\
71 	SICRH_GPIO_A_TSEC2 |\
72 	SICRH_GPIO_B_TSEC2_TX_CLK |\
73 	SICRH_IEEE1588_A_GPIO |\
74 	SICRH_USB |\
75 	SICRH_GTM_GPIO |\
76 	SICRH_IEEE1588_B_GPIO |\
77 	SICRH_ETSEC2_CRS |\
78 	SICRH_GPIOSEL_1 |\
79 	SICRH_TMROBI_V3P3 |\
80 	SICRH_TSOBI1_V3P3 |\
81 	SICRH_TSOBI2_V3P3)	/* 0xf577d100 */
82 #define CONFIG_SYS_SICRL (\
83 	SICRL_SPI_PF0 |\
84 	SICRL_UART_PF0 |\
85 	SICRL_IRQ_PF0 |\
86 	SICRL_I2C2_PF0 |\
87 	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */
88 
89 #define CONFIG_SYS_GPIO1_PRELIM
90 /* GPIO Default input/output settings */
91 #define CONFIG_SYS_GPIO1_DIR        0x7AAF8C00
92 /*
93  * Default GPIO values:
94  * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
95  */
96 #define CONFIG_SYS_GPIO1_DAT        0x08008C00
97 
98 /*
99  * IMMR new address
100  */
101 #define CONFIG_SYS_IMMR		0xE0000000
102 
103 /*
104  * SERDES
105  */
106 #define CONFIG_FSL_SERDES
107 #define CONFIG_FSL_SERDES1	0xe3000
108 
109 /*
110  * Arbiter Setup
111  */
112 #define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
113 #define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
114 #define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
115 
116 /*
117  * DDR Setup
118  */
119 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
120 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
121 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
122 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
123 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
124 				| DDRCDR_PZ_LOZ \
125 				| DDRCDR_NZ_LOZ \
126 				| DDRCDR_ODT \
127 				| DDRCDR_Q_DRN)
128 				/* 0x7b880001 */
129 /*
130  * Manually set up DDR parameters
131  * consist of two chips HY5PS12621BFP-C4 from HYNIX
132  */
133 
134 #define CONFIG_SYS_DDR_SIZE		128 /* MB */
135 
136 #define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
137 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
138 					| CSCONFIG_ODT_RD_NEVER \
139 					| CSCONFIG_ODT_WR_ONLY_CURRENT \
140 					| CSCONFIG_ROW_BIT_13 \
141 					| CSCONFIG_COL_BIT_10)
142 					/* 0x80010102 */
143 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
144 #define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
145 				| (0 << TIMING_CFG0_WRT_SHIFT) \
146 				| (0 << TIMING_CFG0_RRT_SHIFT) \
147 				| (0 << TIMING_CFG0_WWT_SHIFT) \
148 				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
149 				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
150 				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
151 				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
152 				/* 0x00220802 */
153 #define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
154 				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
155 				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
156 				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
157 				| (6 << TIMING_CFG1_REFREC_SHIFT) \
158 				| (2 << TIMING_CFG1_WRREC_SHIFT) \
159 				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
160 				| (2 << TIMING_CFG1_WRTORD_SHIFT))
161 				/* 0x27256222 */
162 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
163 				| (4 << TIMING_CFG2_CPO_SHIFT) \
164 				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
165 				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
166 				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
167 				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
168 				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
169 				/* 0x121048c5 */
170 #define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
171 				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
172 				/* 0x03600100 */
173 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
174 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
175 				| SDRAM_CFG_DBW_32)
176 				/* 0x43080000 */
177 
178 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
179 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
180 				| (0x0232 << SDRAM_MODE_SD_SHIFT))
181 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
182 #define CONFIG_SYS_DDR_MODE2		0x00000000
183 
184 /*
185  * Memory test
186  */
187 #define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
188 #define CONFIG_SYS_MEMTEST_END		0x07f00000
189 
190 /*
191  * The reserved memory
192  */
193 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
194 
195 #define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
196 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
197 
198 /*
199  * Initial RAM Base Address Setup
200  */
201 #define CONFIG_SYS_INIT_RAM_LOCK	1
202 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
203 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
204 #define CONFIG_SYS_GBL_DATA_OFFSET	\
205 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
206 
207 /*
208  * Local Bus Configuration & Clock Setup
209  */
210 #define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
211 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
212 #define CONFIG_SYS_LBC_LBCR		0x00040000
213 
214 /*
215  * FLASH on the Local Bus
216  */
217 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
218 #define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
219 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
220 
221 #define CONFIG_SYS_FLASH_BASE		0xFC000000 /* FLASH base address */
222 #define CONFIG_SYS_FLASH_SIZE		64 /* FLASH size is 64M */
223 #define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */
224 
225 /* Window base at flash base */
226 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
227 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)
228 
229 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
230 				| BR_PS_16	/* 16 bit port */ \
231 				| BR_MS_GPCM	/* MSEL = GPCM */ \
232 				| BR_V)		/* valid */
233 #define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
234 				| OR_UPM_XAM \
235 				| OR_GPCM_CSNT \
236 				| OR_GPCM_ACS_DIV2 \
237 				| OR_GPCM_XACS \
238 				| OR_GPCM_SCY_4 \
239 				| OR_GPCM_TRLX_SET \
240 				| OR_GPCM_EHTR_SET)
241 
242 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
243 #define CONFIG_SYS_MAX_FLASH_SECT	512
244 
245 /* Flash Erase Timeout (ms) */
246 #define CONFIG_SYS_FLASH_ERASE_TOUT	(1000 * 1024)
247 /* Flash Write Timeout (ms) */
248 #define CONFIG_SYS_FLASH_WRITE_TOUT	(500 * 1024)
249 
250 /*
251  * SJA1000 CAN controller on Local Bus
252  */
253 #define CONFIG_SYS_SJA1000_BASE	0xFBFF0000
254 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_SJA1000_BASE \
255 				| BR_PS_8	/* 8 bit port size */ \
256 				| BR_MS_GPCM	/* MSEL = GPCM */ \
257 				| BR_V)		/* valid */
258 #define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
259 				| OR_GPCM_SCY_5 \
260 				| OR_GPCM_EHTR_SET)
261 				/* 0xFFFF8052 */
262 
263 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_SJA1000_BASE
264 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
265 
266 /*
267  * CPLD on Local Bus
268  */
269 #define CONFIG_SYS_CPLD_BASE	0xFBFF8000
270 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_CPLD_BASE \
271 				| BR_PS_8	/* 8 bit port */ \
272 				| BR_MS_GPCM	/* MSEL = GPCM */ \
273 				| BR_V)		/* valid */
274 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_32KB \
275 				| OR_GPCM_SCY_4 \
276 				| OR_GPCM_EHTR_SET)
277 				/* 0xFFFF8042 */
278 
279 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_CPLD_BASE
280 #define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
281 
282 /*
283  * Serial Port
284  */
285 #undef CONFIG_SERIAL_SOFTWARE_FIFO
286 #define CONFIG_SYS_NS16550_SERIAL
287 #define CONFIG_SYS_NS16550_REG_SIZE	1
288 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
289 
290 #define CONFIG_SYS_BAUDRATE_TABLE  \
291 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
292 
293 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
294 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
295 
296 /* I2C */
297 #define CONFIG_SYS_I2C
298 #define CONFIG_SYS_I2C_FSL
299 #define CONFIG_SYS_FSL_I2C_SPEED	400000
300 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
301 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
302 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
303 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
304 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
305 
306 /*
307  * General PCI
308  * Addresses are mapped 1-1.
309  */
310 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
311 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
312 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
313 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
314 #define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
315 #define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
316 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
317 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
318 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
319 
320 /* enable PCIE clock */
321 #define CONFIG_SYS_SCCR_PCIEXP1CM	1
322 
323 #define CONFIG_PCI_INDIRECT_BRIDGE
324 #define CONFIG_PCIE
325 
326 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
327 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
328 
329 /*
330  * TSEC
331  */
332 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
333 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
334 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
335 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
336 
337 /*
338  * TSEC ethernet configuration
339  */
340 #define CONFIG_TSEC1_NAME	"eTSEC0"
341 #define CONFIG_TSEC2_NAME	"eTSEC1"
342 #define TSEC1_PHY_ADDR		1
343 #define TSEC2_PHY_ADDR		2
344 #define TSEC1_PHYIDX		0
345 #define TSEC2_PHYIDX		0
346 #define TSEC1_FLAGS		0
347 #define TSEC2_FLAGS		0
348 
349 /* Options are: eTSEC[0-1] */
350 #define CONFIG_ETHPRIME		"eTSEC0"
351 
352 /*
353  * Environment
354  */
355 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
356 				 CONFIG_SYS_MONITOR_LEN)
357 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
358 #define CONFIG_ENV_SIZE		0x2000
359 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
360 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
361 
362 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
363 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
364 
365 /*
366  * BOOTP options
367  */
368 #define CONFIG_BOOTP_BOOTFILESIZE
369 
370 /*
371  * Command line configuration.
372  */
373 
374 /*
375  * Miscellaneous configurable options
376  */
377 #define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
378 
379 #define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
380 
381 /* Boot Argument Buffer Size */
382 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
383 
384 /*
385  * For booting Linux, the board info and command line data
386  * have to be in the first 8 MB of memory, since this is
387  * the maximum mapped by the Linux kernel during initialization.
388  */
389 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
390 
391 /*
392  * Core HID Setup
393  */
394 #define CONFIG_SYS_HID0_INIT	0x000000000
395 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
396 				 HID0_ENABLE_INSTRUCTION_CACHE | \
397 				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
398 #define CONFIG_SYS_HID2		HID2_HBE
399 
400 /*
401  * MMU Setup
402  */
403 
404 /* DDR: cache cacheable */
405 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
406 					BATL_MEMCOHERENCE)
407 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
408 					BATU_VS | BATU_VP)
409 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
410 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
411 
412 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
413 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
414 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
415 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
416 					BATU_VP)
417 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
418 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
419 
420 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
421 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
422 					BATL_MEMCOHERENCE)
423 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
424 					BATU_VS | BATU_VP)
425 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
426 					BATL_CACHEINHIBIT | \
427 					BATL_GUARDEDSTORAGE)
428 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
429 
430 /* Stack in dcache: cacheable, no memory coherence */
431 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
432 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
433 					BATU_VS | BATU_VP)
434 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
435 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
436 
437 /*
438  * Environment Configuration
439  */
440 
441 #define CONFIG_ENV_OVERWRITE
442 
443 #if defined(CONFIG_TSEC_ENET)
444 #define CONFIG_HAS_ETH0
445 #define CONFIG_HAS_ETH1
446 #endif
447 
448 #define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
449 
450 
451 #define	CONFIG_EXTRA_ENV_SETTINGS					\
452 	"netdev=eth0\0"							\
453 	"consoledev=ttyS0\0"						\
454 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
455 		"nfsroot=${serverip}:${rootpath}\0"			\
456 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
457 	"addip=setenv bootargs ${bootargs} "				\
458 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
459 		":${hostname}:${netdev}:off panic=1\0"			\
460 	"addtty=setenv bootargs ${bootargs}"				\
461 		" console=${consoledev},${baudrate}\0"			\
462 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
463 	"addmisc=setenv bootargs ${bootargs}\0"				\
464 	"kernel_addr=FC0A0000\0"					\
465 	"fdt_addr=FC2A0000\0"						\
466 	"ramdisk_addr=FC2C0000\0"					\
467 	"u-boot=mpc8308_p1m/u-boot.bin\0"				\
468 	"kernel_addr_r=1000000\0"					\
469 	"fdt_addr_r=C00000\0"						\
470 	"hostname=mpc8308_p1m\0"					\
471 	"bootfile=mpc8308_p1m/uImage\0"					\
472 	"fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0"				\
473 	"rootpath=/opt/eldk-4.2/ppc_6xx\0"				\
474 	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
475 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
476 	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
477 		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
478 	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
479 		"tftp ${fdt_addr_r} ${fdtfile};"			\
480 		"run nfsargs addip addtty addmtd addmisc;"		\
481 		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
482 	"bootcmd=run flash_self\0"					\
483 	"load=tftp ${loadaddr} ${u-boot}\0"				\
484 	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
485 		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
486 		" +${filesize};cp.b ${fileaddr} "			\
487 		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
488 	"upd=run load update\0"						\
489 
490 #endif	/* __CONFIG_H */
491