1 /*
2  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
3  * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
4  *
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #ifndef __CONFIG_H
10 #define __CONFIG_H
11 
12 #define CONFIG_DISPLAY_BOARDINFO
13 
14 /*
15  * High Level Configuration Options
16  */
17 #define CONFIG_E300		1 /* E300 family */
18 #define CONFIG_MPC830x		1 /* MPC830x family */
19 #define CONFIG_MPC8308		1 /* MPC8308 CPU specific */
20 #define CONFIG_MPC8308_P1M	1 /* mpc8308_p1m board specific */
21 
22 #ifndef CONFIG_SYS_TEXT_BASE
23 #define CONFIG_SYS_TEXT_BASE	0xFC000000
24 #endif
25 
26 /*
27  * On-board devices
28  *
29  * TSECs
30  */
31 #define CONFIG_TSEC1
32 #define CONFIG_TSEC2
33 
34 /*
35  * System Clock Setup
36  */
37 #define CONFIG_83XX_CLKIN	33333333 /* in Hz */
38 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
39 
40 /*
41  * Hardware Reset Configuration Word
42  * if CLKIN is 66.66MHz, then
43  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
44  * We choose the A type silicon as default, so the core is 400Mhz.
45  */
46 #define CONFIG_SYS_HRCW_LOW (\
47 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
48 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
49 	HRCWL_SVCOD_DIV_2 |\
50 	HRCWL_CSB_TO_CLKIN_4X1 |\
51 	HRCWL_CORE_TO_CSB_3X1)
52 /*
53  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
54  * in 8308's HRCWH according to the manual, but original Freescale's
55  * code has them and I've expirienced some problems using the board
56  * with BDI3000 attached when I've tried to set these bits to zero
57  * (UART doesn't work after the 'reset run' command).
58  */
59 #define CONFIG_SYS_HRCW_HIGH (\
60 	HRCWH_PCI_HOST |\
61 	HRCWH_PCI1_ARBITER_ENABLE |\
62 	HRCWH_CORE_ENABLE |\
63 	HRCWH_FROM_0X00000100 |\
64 	HRCWH_BOOTSEQ_DISABLE |\
65 	HRCWH_SW_WATCHDOG_DISABLE |\
66 	HRCWH_ROM_LOC_LOCAL_16BIT |\
67 	HRCWH_RL_EXT_LEGACY |\
68 	HRCWH_TSEC1M_IN_MII |\
69 	HRCWH_TSEC2M_IN_MII |\
70 	HRCWH_BIG_ENDIAN)
71 
72 /*
73  * System IO Config
74  */
75 #define CONFIG_SYS_SICRH (\
76 	SICRH_ESDHC_A_GPIO |\
77 	SICRH_ESDHC_B_GPIO |\
78 	SICRH_ESDHC_C_GTM |\
79 	SICRH_GPIO_A_TSEC2 |\
80 	SICRH_GPIO_B_TSEC2_TX_CLK |\
81 	SICRH_IEEE1588_A_GPIO |\
82 	SICRH_USB |\
83 	SICRH_GTM_GPIO |\
84 	SICRH_IEEE1588_B_GPIO |\
85 	SICRH_ETSEC2_CRS |\
86 	SICRH_GPIOSEL_1 |\
87 	SICRH_TMROBI_V3P3 |\
88 	SICRH_TSOBI1_V3P3 |\
89 	SICRH_TSOBI2_V3P3)	/* 0xf577d100 */
90 #define CONFIG_SYS_SICRL (\
91 	SICRL_SPI_PF0 |\
92 	SICRL_UART_PF0 |\
93 	SICRL_IRQ_PF0 |\
94 	SICRL_I2C2_PF0 |\
95 	SICRL_ETSEC1_TX_CLK)	/* 0x00000000 */
96 
97 #define CONFIG_SYS_GPIO1_PRELIM
98 /* GPIO Default input/output settings */
99 #define CONFIG_SYS_GPIO1_DIR        0x7AAF8C00
100 /*
101  * Default GPIO values:
102  * LED#1 enabled; WLAN enabled; Both COM LED on (orange)
103  */
104 #define CONFIG_SYS_GPIO1_DAT        0x08008C00
105 
106 /*
107  * IMMR new address
108  */
109 #define CONFIG_SYS_IMMR		0xE0000000
110 
111 /*
112  * SERDES
113  */
114 #define CONFIG_FSL_SERDES
115 #define CONFIG_FSL_SERDES1	0xe3000
116 
117 /*
118  * Arbiter Setup
119  */
120 #define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
121 #define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
122 #define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
123 
124 /*
125  * DDR Setup
126  */
127 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
128 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
129 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
130 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
131 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
132 				| DDRCDR_PZ_LOZ \
133 				| DDRCDR_NZ_LOZ \
134 				| DDRCDR_ODT \
135 				| DDRCDR_Q_DRN)
136 				/* 0x7b880001 */
137 /*
138  * Manually set up DDR parameters
139  * consist of two chips HY5PS12621BFP-C4 from HYNIX
140  */
141 
142 #define CONFIG_SYS_DDR_SIZE		128 /* MB */
143 
144 #define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
145 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
146 					| CSCONFIG_ODT_RD_NEVER \
147 					| CSCONFIG_ODT_WR_ONLY_CURRENT \
148 					| CSCONFIG_ROW_BIT_13 \
149 					| CSCONFIG_COL_BIT_10)
150 					/* 0x80010102 */
151 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
152 #define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
153 				| (0 << TIMING_CFG0_WRT_SHIFT) \
154 				| (0 << TIMING_CFG0_RRT_SHIFT) \
155 				| (0 << TIMING_CFG0_WWT_SHIFT) \
156 				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
157 				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
158 				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
159 				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
160 				/* 0x00220802 */
161 #define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
162 				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
163 				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
164 				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
165 				| (6 << TIMING_CFG1_REFREC_SHIFT) \
166 				| (2 << TIMING_CFG1_WRREC_SHIFT) \
167 				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
168 				| (2 << TIMING_CFG1_WRTORD_SHIFT))
169 				/* 0x27256222 */
170 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
171 				| (4 << TIMING_CFG2_CPO_SHIFT) \
172 				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
173 				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
174 				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
175 				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
176 				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
177 				/* 0x121048c5 */
178 #define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
179 				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
180 				/* 0x03600100 */
181 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
182 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
183 				| SDRAM_CFG_DBW_32)
184 				/* 0x43080000 */
185 
186 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
187 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
188 				| (0x0232 << SDRAM_MODE_SD_SHIFT))
189 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
190 #define CONFIG_SYS_DDR_MODE2		0x00000000
191 
192 /*
193  * Memory test
194  */
195 #define CONFIG_SYS_MEMTEST_START	0x00001000 /* memtest region */
196 #define CONFIG_SYS_MEMTEST_END		0x07f00000
197 
198 /*
199  * The reserved memory
200  */
201 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
202 
203 #define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
204 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
205 
206 /*
207  * Initial RAM Base Address Setup
208  */
209 #define CONFIG_SYS_INIT_RAM_LOCK	1
210 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
211 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
212 #define CONFIG_SYS_GBL_DATA_OFFSET	\
213 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
214 
215 /*
216  * Local Bus Configuration & Clock Setup
217  */
218 #define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
219 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
220 #define CONFIG_SYS_LBC_LBCR		0x00040000
221 
222 /*
223  * FLASH on the Local Bus
224  */
225 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
226 #define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
227 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
228 
229 #define CONFIG_SYS_FLASH_BASE		0xFC000000 /* FLASH base address */
230 #define CONFIG_SYS_FLASH_SIZE		64 /* FLASH size is 64M */
231 #define CONFIG_SYS_FLASH_PROTECTION	1 /* Use h/w Flash protection. */
232 
233 /* Window base at flash base */
234 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
235 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)
236 
237 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE \
238 				| BR_PS_16	/* 16 bit port */ \
239 				| BR_MS_GPCM	/* MSEL = GPCM */ \
240 				| BR_V)		/* valid */
241 #define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
242 				| OR_UPM_XAM \
243 				| OR_GPCM_CSNT \
244 				| OR_GPCM_ACS_DIV2 \
245 				| OR_GPCM_XACS \
246 				| OR_GPCM_SCY_4 \
247 				| OR_GPCM_TRLX_SET \
248 				| OR_GPCM_EHTR_SET)
249 
250 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
251 #define CONFIG_SYS_MAX_FLASH_SECT	512
252 
253 /* Flash Erase Timeout (ms) */
254 #define CONFIG_SYS_FLASH_ERASE_TOUT	(1000 * 1024)
255 /* Flash Write Timeout (ms) */
256 #define CONFIG_SYS_FLASH_WRITE_TOUT	(500 * 1024)
257 
258 /*
259  * SJA1000 CAN controller on Local Bus
260  */
261 #define CONFIG_SYS_SJA1000_BASE	0xFBFF0000
262 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_SJA1000_BASE \
263 				| BR_PS_8	/* 8 bit port size */ \
264 				| BR_MS_GPCM	/* MSEL = GPCM */ \
265 				| BR_V)		/* valid */
266 #define CONFIG_SYS_OR1_PRELIM	(OR_AM_32KB \
267 				| OR_GPCM_SCY_5 \
268 				| OR_GPCM_EHTR_SET)
269 				/* 0xFFFF8052 */
270 
271 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_SJA1000_BASE
272 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
273 
274 /*
275  * CPLD on Local Bus
276  */
277 #define CONFIG_SYS_CPLD_BASE	0xFBFF8000
278 #define CONFIG_SYS_BR2_PRELIM	(CONFIG_SYS_CPLD_BASE \
279 				| BR_PS_8	/* 8 bit port */ \
280 				| BR_MS_GPCM	/* MSEL = GPCM */ \
281 				| BR_V)		/* valid */
282 #define CONFIG_SYS_OR2_PRELIM	(OR_AM_32KB \
283 				| OR_GPCM_SCY_4 \
284 				| OR_GPCM_EHTR_SET)
285 				/* 0xFFFF8042 */
286 
287 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_CPLD_BASE
288 #define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
289 
290 /*
291  * Serial Port
292  */
293 #define CONFIG_CONS_INDEX	1
294 #undef CONFIG_SERIAL_SOFTWARE_FIFO
295 #define CONFIG_SYS_NS16550_SERIAL
296 #define CONFIG_SYS_NS16550_REG_SIZE	1
297 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
298 
299 #define CONFIG_SYS_BAUDRATE_TABLE  \
300 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
301 
302 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
303 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
304 
305 /* Use the HUSH parser */
306 #define CONFIG_SYS_HUSH_PARSER
307 
308 /* I2C */
309 #define CONFIG_SYS_I2C
310 #define CONFIG_SYS_I2C_FSL
311 #define CONFIG_SYS_FSL_I2C_SPEED	400000
312 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
313 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
314 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
315 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
316 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
317 
318 /*
319  * General PCI
320  * Addresses are mapped 1-1.
321  */
322 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
323 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
324 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
325 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
326 #define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
327 #define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
328 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
329 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
330 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
331 
332 /* enable PCIE clock */
333 #define CONFIG_SYS_SCCR_PCIEXP1CM	1
334 
335 #define CONFIG_PCI
336 #define CONFIG_PCI_INDIRECT_BRIDGE
337 #define CONFIG_PCIE
338 
339 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
340 
341 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
342 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
343 
344 /*
345  * TSEC
346  */
347 #define CONFIG_TSEC_ENET	/* TSEC ethernet support */
348 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
349 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
350 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
351 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
352 
353 /*
354  * TSEC ethernet configuration
355  */
356 #define CONFIG_MII		1 /* MII PHY management */
357 #define CONFIG_TSEC1_NAME	"eTSEC0"
358 #define CONFIG_TSEC2_NAME	"eTSEC1"
359 #define TSEC1_PHY_ADDR		1
360 #define TSEC2_PHY_ADDR		2
361 #define TSEC1_PHYIDX		0
362 #define TSEC2_PHYIDX		0
363 #define TSEC1_FLAGS		0
364 #define TSEC2_FLAGS		0
365 
366 /* Options are: eTSEC[0-1] */
367 #define CONFIG_ETHPRIME		"eTSEC0"
368 
369 /*
370  * Environment
371  */
372 #define CONFIG_ENV_IS_IN_FLASH	1
373 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
374 				 CONFIG_SYS_MONITOR_LEN)
375 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
376 #define CONFIG_ENV_SIZE		0x2000
377 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
378 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
379 
380 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
381 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
382 
383 /*
384  * BOOTP options
385  */
386 #define CONFIG_BOOTP_BOOTFILESIZE
387 #define CONFIG_BOOTP_BOOTPATH
388 #define CONFIG_BOOTP_GATEWAY
389 #define CONFIG_BOOTP_HOSTNAME
390 
391 /*
392  * Command line configuration.
393  */
394 #define CONFIG_CMD_DHCP
395 #define CONFIG_CMD_I2C
396 #define CONFIG_CMD_MII
397 #define CONFIG_CMD_PCI
398 #define CONFIG_CMD_PING
399 
400 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
401 
402 /*
403  * Miscellaneous configurable options
404  */
405 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
406 #define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
407 
408 #define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
409 
410 /* Print Buffer Size */
411 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
412 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
413 /* Boot Argument Buffer Size */
414 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
415 
416 /*
417  * For booting Linux, the board info and command line data
418  * have to be in the first 8 MB of memory, since this is
419  * the maximum mapped by the Linux kernel during initialization.
420  */
421 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
422 
423 /*
424  * Core HID Setup
425  */
426 #define CONFIG_SYS_HID0_INIT	0x000000000
427 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
428 				 HID0_ENABLE_INSTRUCTION_CACHE | \
429 				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
430 #define CONFIG_SYS_HID2		HID2_HBE
431 
432 /*
433  * MMU Setup
434  */
435 
436 /* DDR: cache cacheable */
437 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
438 					BATL_MEMCOHERENCE)
439 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
440 					BATU_VS | BATU_VP)
441 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
442 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
443 
444 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
445 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_RW | \
446 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
447 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
448 					BATU_VP)
449 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
450 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
451 
452 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
453 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
454 					BATL_MEMCOHERENCE)
455 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
456 					BATU_VS | BATU_VP)
457 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
458 					BATL_CACHEINHIBIT | \
459 					BATL_GUARDEDSTORAGE)
460 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
461 
462 /* Stack in dcache: cacheable, no memory coherence */
463 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
464 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
465 					BATU_VS | BATU_VP)
466 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
467 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
468 
469 /*
470  * Environment Configuration
471  */
472 
473 #define CONFIG_ENV_OVERWRITE
474 
475 #if defined(CONFIG_TSEC_ENET)
476 #define CONFIG_HAS_ETH0
477 #define CONFIG_HAS_ETH1
478 #endif
479 
480 #define CONFIG_BAUDRATE 115200
481 
482 #define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
483 
484 #define CONFIG_BOOTDELAY	5	/* -1 disables auto-boot */
485 
486 #define	CONFIG_EXTRA_ENV_SETTINGS					\
487 	"netdev=eth0\0"							\
488 	"consoledev=ttyS0\0"						\
489 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
490 		"nfsroot=${serverip}:${rootpath}\0"			\
491 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
492 	"addip=setenv bootargs ${bootargs} "				\
493 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
494 		":${hostname}:${netdev}:off panic=1\0"			\
495 	"addtty=setenv bootargs ${bootargs}"				\
496 		" console=${consoledev},${baudrate}\0"			\
497 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
498 	"addmisc=setenv bootargs ${bootargs}\0"				\
499 	"kernel_addr=FC0A0000\0"					\
500 	"fdt_addr=FC2A0000\0"						\
501 	"ramdisk_addr=FC2C0000\0"					\
502 	"u-boot=mpc8308_p1m/u-boot.bin\0"				\
503 	"kernel_addr_r=1000000\0"					\
504 	"fdt_addr_r=C00000\0"						\
505 	"hostname=mpc8308_p1m\0"					\
506 	"bootfile=mpc8308_p1m/uImage\0"					\
507 	"fdtfile=mpc8308_p1m/mpc8308_p1m.dtb\0"				\
508 	"rootpath=/opt/eldk-4.2/ppc_6xx\0"				\
509 	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
510 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
511 	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
512 		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
513 	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
514 		"tftp ${fdt_addr_r} ${fdtfile};"			\
515 		"run nfsargs addip addtty addmtd addmisc;"		\
516 		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
517 	"bootcmd=run flash_self\0"					\
518 	"load=tftp ${loadaddr} ${u-boot}\0"				\
519 	"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)	\
520 		" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
521 		" +${filesize};cp.b ${fileaddr} "			\
522 		__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"	\
523 	"upd=run load update\0"						\
524 
525 #endif	/* __CONFIG_H */
526