1 /* 2 * (C) Copyright 2007-2010 Michal Simek 3 * 4 * Michal SIMEK <monstr@monstr.eu> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include "../board/xilinx/microblaze-generic/xparameters.h" 13 14 /* MicroBlaze CPU */ 15 #define MICROBLAZE_V5 1 16 17 /* linear and spi flash memory */ 18 #ifdef XILINX_FLASH_START 19 #define FLASH 20 #undef SPIFLASH 21 #undef RAMENV /* hold environment in flash */ 22 #else 23 #ifdef XILINX_SPI_FLASH_BASEADDR 24 #undef FLASH 25 #define SPIFLASH 26 #undef RAMENV /* hold environment in flash */ 27 #else 28 #undef FLASH 29 #undef SPIFLASH 30 #define RAMENV /* hold environment in RAM */ 31 #endif 32 #endif 33 34 /* uart */ 35 # define CONFIG_BAUDRATE 115200 36 /* The following table includes the supported baudrates */ 37 # define CONFIG_SYS_BAUDRATE_TABLE \ 38 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 39 40 /* setting reset address */ 41 /*#define CONFIG_SYS_RESET_ADDRESS CONFIG_SYS_TEXT_BASE*/ 42 43 /* gpio */ 44 #ifdef XILINX_GPIO_BASEADDR 45 # define CONFIG_XILINX_GPIO 46 # define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR 47 #endif 48 #define CONFIG_BOARD_LATE_INIT 49 50 /* watchdog */ 51 #if defined(XILINX_WATCHDOG_BASEADDR) && defined(XILINX_WATCHDOG_IRQ) 52 # define CONFIG_WATCHDOG_BASEADDR XILINX_WATCHDOG_BASEADDR 53 # define CONFIG_WATCHDOG_IRQ XILINX_WATCHDOG_IRQ 54 # ifndef CONFIG_SPL_BUILD 55 # define CONFIG_HW_WATCHDOG 56 # define CONFIG_XILINX_TB_WATCHDOG 57 # endif 58 #endif 59 60 #define CONFIG_SYS_MALLOC_LEN 0xC0000 61 62 /* Stack location before relocation */ 63 #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_TEXT_BASE - \ 64 CONFIG_SYS_MALLOC_F_LEN) 65 66 /* 67 * CFI flash memory layout - Example 68 * CONFIG_SYS_FLASH_BASE = 0x2200_0000; 69 * CONFIG_SYS_FLASH_SIZE = 0x0080_0000; 8MB 70 * 71 * SECT_SIZE = 0x20000; 128kB is one sector 72 * CONFIG_ENV_SIZE = SECT_SIZE; 128kB environment store 73 * 74 * 0x2200_0000 CONFIG_SYS_FLASH_BASE 75 * FREE 256kB 76 * 0x2204_0000 CONFIG_ENV_ADDR 77 * ENV_AREA 128kB 78 * 0x2206_0000 79 * FREE 80 * 0x2280_0000 CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE 81 * 82 */ 83 84 #ifdef FLASH 85 # define CONFIG_SYS_FLASH_BASE XILINX_FLASH_START 86 # define CONFIG_SYS_FLASH_SIZE XILINX_FLASH_SIZE 87 # define CONFIG_SYS_FLASH_CFI 1 88 # define CONFIG_FLASH_CFI_DRIVER 1 89 /* ?empty sector */ 90 # define CONFIG_SYS_FLASH_EMPTY_INFO 1 91 /* max number of memory banks */ 92 # define CONFIG_SYS_MAX_FLASH_BANKS 1 93 /* max number of sectors on one chip */ 94 # define CONFIG_SYS_MAX_FLASH_SECT 512 95 /* hardware flash protection */ 96 # define CONFIG_SYS_FLASH_PROTECTION 97 /* use buffered writes (20x faster) */ 98 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 99 # ifdef RAMENV 100 # define CONFIG_ENV_IS_NOWHERE 1 101 # define CONFIG_ENV_SIZE 0x1000 102 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 103 104 # else /* FLASH && !RAMENV */ 105 # define CONFIG_ENV_IS_IN_FLASH 1 106 /* 128K(one sector) for env */ 107 # define CONFIG_ENV_SECT_SIZE 0x20000 108 # define CONFIG_ENV_ADDR \ 109 (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) 110 # define CONFIG_ENV_SIZE 0x20000 111 # endif /* FLASH && !RAMBOOT */ 112 #else /* !FLASH */ 113 114 #ifdef SPIFLASH 115 # define CONFIG_SYS_NO_FLASH 1 116 # define CONFIG_SYS_SPI_BASE XILINX_SPI_FLASH_BASEADDR 117 # define CONFIG_SPI 1 118 # define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 119 # define CONFIG_SF_DEFAULT_SPEED XILINX_SPI_FLASH_MAX_FREQ 120 # define CONFIG_SF_DEFAULT_CS XILINX_SPI_FLASH_CS 121 122 # ifdef RAMENV 123 # define CONFIG_ENV_IS_NOWHERE 1 124 # define CONFIG_ENV_SIZE 0x1000 125 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 126 127 # else /* SPIFLASH && !RAMENV */ 128 # define CONFIG_ENV_IS_IN_SPI_FLASH 1 129 # define CONFIG_ENV_SPI_MODE SPI_MODE_3 130 # define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 131 # define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 132 /* 128K(two sectors) for env */ 133 # define CONFIG_ENV_SECT_SIZE 0x10000 134 # define CONFIG_ENV_SIZE (2 * CONFIG_ENV_SECT_SIZE) 135 /* Warning: adjust the offset in respect of other flash content and size */ 136 # define CONFIG_ENV_OFFSET (128 * CONFIG_ENV_SECT_SIZE) /* at 8MB */ 137 # endif /* SPIFLASH && !RAMBOOT */ 138 #else /* !SPIFLASH */ 139 140 /* ENV in RAM */ 141 # define CONFIG_SYS_NO_FLASH 1 142 # define CONFIG_ENV_IS_NOWHERE 1 143 # define CONFIG_ENV_SIZE 0x1000 144 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 145 #endif /* !SPIFLASH */ 146 #endif /* !FLASH */ 147 148 #if defined(XILINX_USE_ICACHE) 149 # define CONFIG_ICACHE 150 #else 151 # undef CONFIG_ICACHE 152 #endif 153 154 #if defined(XILINX_USE_DCACHE) 155 # define CONFIG_DCACHE 156 #else 157 # undef CONFIG_DCACHE 158 #endif 159 160 #ifndef XILINX_DCACHE_BYTE_SIZE 161 #define XILINX_DCACHE_BYTE_SIZE 32768 162 #endif 163 164 /* 165 * BOOTP options 166 */ 167 #define CONFIG_BOOTP_BOOTFILESIZE 168 #define CONFIG_BOOTP_BOOTPATH 169 #define CONFIG_BOOTP_GATEWAY 170 #define CONFIG_BOOTP_HOSTNAME 171 172 /* 173 * Command line configuration. 174 */ 175 #define CONFIG_CMD_IRQ 176 #define CONFIG_CMD_MFSL 177 178 #if defined(CONFIG_DCACHE) || defined(CONFIG_ICACHE) 179 #else 180 #endif 181 182 #if defined(FLASH) 183 # define CONFIG_CMD_JFFS2 184 # define CONFIG_CMD_UBI 185 # undef CONFIG_CMD_UBIFS 186 187 # if !defined(RAMENV) 188 # define CONFIG_CMD_SAVES 189 # endif 190 191 #else 192 #if defined(SPIFLASH) 193 194 # if !defined(RAMENV) 195 # define CONFIG_CMD_SAVES 196 # endif 197 #else 198 # undef CONFIG_CMD_JFFS2 199 # undef CONFIG_CMD_UBI 200 # undef CONFIG_CMD_UBIFS 201 #endif 202 #endif 203 204 #if defined(CONFIG_CMD_JFFS2) 205 # define CONFIG_MTD_PARTITIONS 206 #endif 207 208 #if defined(CONFIG_CMD_UBIFS) 209 # define CONFIG_CMD_UBI 210 # define CONFIG_LZO 211 #endif 212 213 #if defined(CONFIG_CMD_UBI) 214 # define CONFIG_MTD_PARTITIONS 215 # define CONFIG_RBTREE 216 #endif 217 218 #if defined(CONFIG_MTD_PARTITIONS) 219 /* MTD partitions */ 220 #define CONFIG_CMD_MTDPARTS /* mtdparts command line support */ 221 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 222 #define CONFIG_FLASH_CFI_MTD 223 #define MTDIDS_DEFAULT "nor0=flash-0" 224 225 /* default mtd partition table */ 226 #define MTDPARTS_DEFAULT "mtdparts=flash-0:256k(u-boot),"\ 227 "256k(env),3m(kernel),1m(romfs),"\ 228 "1m(cramfs),-(jffs2)" 229 #endif 230 231 /* size of console buffer */ 232 #define CONFIG_SYS_CBSIZE 512 233 /* print buffer size */ 234 #define CONFIG_SYS_PBSIZE \ 235 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 236 /* max number of command args */ 237 #define CONFIG_SYS_MAXARGS 15 238 #define CONFIG_SYS_LONGHELP 239 /* default load address */ 240 #define CONFIG_SYS_LOAD_ADDR 0 241 242 #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ 243 #define CONFIG_BOOTARGS "root=romfs" 244 #define CONFIG_HOSTNAME XILINX_BOARD_NAME 245 #define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm" 246 #define CONFIG_IPADDR 192.168.0.3 247 #define CONFIG_SERVERIP 192.168.0.5 248 #define CONFIG_GATEWAYIP 192.168.0.1 249 250 /* architecture dependent code */ 251 #define CONFIG_SYS_USR_EXCEP /* user exception */ 252 253 #define CONFIG_PREBOOT "echo U-BOOT for ${hostname};setenv preboot;echo" 254 255 #define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" \ 256 "nor0=flash-0\0"\ 257 "mtdparts=mtdparts=flash-0:"\ 258 "256k(u-boot),256k(env),3m(kernel),"\ 259 "1m(romfs),1m(cramfs),-(jffs2)\0"\ 260 "nc=setenv stdout nc;"\ 261 "setenv stdin nc\0" \ 262 "serial=setenv stdout serial;"\ 263 "setenv stdin serial\0" 264 265 #define CONFIG_CMDLINE_EDITING 266 267 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 268 269 /* Enable flat device tree support */ 270 #define CONFIG_LMB 1 271 272 #if defined(CONFIG_XILINX_AXIEMAC) 273 # define CONFIG_MII 1 274 # define CONFIG_PHY_GIGE 1 275 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1 276 # define CONFIG_PHY_ATHEROS 1 277 # define CONFIG_PHY_BROADCOM 1 278 # define CONFIG_PHY_DAVICOM 1 279 # define CONFIG_PHY_LXT 1 280 # define CONFIG_PHY_MARVELL 1 281 # define CONFIG_PHY_MICREL 1 282 # define CONFIG_PHY_MICREL_KSZ9021 283 # define CONFIG_PHY_NATSEMI 1 284 # define CONFIG_PHY_REALTEK 1 285 # define CONFIG_PHY_VITESSE 1 286 #else 287 # undef CONFIG_MII 288 #endif 289 290 /* SPL part */ 291 #define CONFIG_CMD_SPL 292 #define CONFIG_SPL_FRAMEWORK 293 #define CONFIG_SPL_LIBCOMMON_SUPPORT 294 #define CONFIG_SPL_LIBGENERIC_SUPPORT 295 #define CONFIG_SPL_SERIAL_SUPPORT 296 #define CONFIG_SPL_BOARD_INIT 297 298 #define CONFIG_SPL_LDSCRIPT "arch/microblaze/cpu/u-boot-spl.lds" 299 300 #define CONFIG_SPL_RAM_DEVICE 301 #ifdef CONFIG_SYS_FLASH_BASE 302 # define CONFIG_SPL_NOR_SUPPORT 303 # define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_FLASH_BASE 304 #endif 305 306 /* for booting directly linux */ 307 #define CONFIG_SPL_OS_BOOT 308 309 #define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + \ 310 0x60000) 311 #define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \ 312 0x40000) 313 #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_TEXT_BASE + \ 314 0x1000000) 315 316 /* SP location before relocation, must use scratch RAM */ 317 /* BRAM start */ 318 #define CONFIG_SYS_INIT_RAM_ADDR 0x0 319 /* BRAM size - will be generated */ 320 #define CONFIG_SYS_INIT_RAM_SIZE 0x100000 321 322 # define CONFIG_SPL_STACK_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 323 CONFIG_SYS_INIT_RAM_SIZE - \ 324 CONFIG_SYS_MALLOC_F_LEN) 325 326 /* Just for sure that there is a space for stack */ 327 #define CONFIG_SPL_STACK_SIZE 0x100 328 329 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 330 331 #define CONFIG_SPL_MAX_FOOTPRINT (CONFIG_SYS_INIT_RAM_SIZE - \ 332 CONFIG_SYS_INIT_RAM_ADDR - \ 333 CONFIG_SYS_MALLOC_F_LEN - \ 334 CONFIG_SPL_STACK_SIZE) 335 336 #endif /* __CONFIG_H */ 337