1 /* 2 * (C) Copyright 2007-2010 Michal Simek 3 * 4 * Michal SIMEK <monstr@monstr.eu> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include "../board/xilinx/microblaze-generic/xparameters.h" 13 14 /* MicroBlaze CPU */ 15 #define MICROBLAZE_V5 1 16 17 /* linear and spi flash memory */ 18 #ifdef XILINX_FLASH_START 19 #define FLASH 20 #undef SPIFLASH 21 #undef RAMENV /* hold environment in flash */ 22 #else 23 #ifdef XILINX_SPI_FLASH_BASEADDR 24 #undef FLASH 25 #define SPIFLASH 26 #undef RAMENV /* hold environment in flash */ 27 #else 28 #undef FLASH 29 #undef SPIFLASH 30 #define RAMENV /* hold environment in RAM */ 31 #endif 32 #endif 33 34 /* uart */ 35 # define CONFIG_BAUDRATE 115200 36 /* The following table includes the supported baudrates */ 37 # define CONFIG_SYS_BAUDRATE_TABLE \ 38 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} 39 40 /* setting reset address */ 41 /*#define CONFIG_SYS_RESET_ADDRESS CONFIG_SYS_TEXT_BASE*/ 42 43 /* gpio */ 44 #ifdef XILINX_GPIO_BASEADDR 45 # define CONFIG_XILINX_GPIO 46 # define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR 47 #endif 48 49 /* interrupt controller */ 50 #ifdef XILINX_INTC_BASEADDR 51 # define CONFIG_SYS_INTC_0_ADDR XILINX_INTC_BASEADDR 52 # define CONFIG_SYS_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS 53 #endif 54 55 /* timer */ 56 #if defined(XILINX_TIMER_BASEADDR) && defined(XILINX_TIMER_IRQ) 57 # define CONFIG_SYS_TIMER_0_ADDR XILINX_TIMER_BASEADDR 58 # define CONFIG_SYS_TIMER_0_IRQ XILINX_TIMER_IRQ 59 #endif 60 61 /* watchdog */ 62 #if defined(XILINX_WATCHDOG_BASEADDR) && defined(XILINX_WATCHDOG_IRQ) 63 # define CONFIG_WATCHDOG_BASEADDR XILINX_WATCHDOG_BASEADDR 64 # define CONFIG_WATCHDOG_IRQ XILINX_WATCHDOG_IRQ 65 # ifndef CONFIG_SPL_BUILD 66 # define CONFIG_HW_WATCHDOG 67 # define CONFIG_XILINX_TB_WATCHDOG 68 # endif 69 #endif 70 71 #if !defined(CONFIG_OF_CONTROL) || \ 72 (defined(CONFIG_SPL_BUILD) && !defined(CONFIG_SPL_OF_CONTROL)) 73 /* ddr sdram - main memory */ 74 # define CONFIG_SYS_SDRAM_BASE XILINX_RAM_START 75 # define CONFIG_SYS_SDRAM_SIZE XILINX_RAM_SIZE 76 #endif 77 78 #define CONFIG_SYS_MALLOC_LEN 0xC0000 79 80 /* Stack location before relocation */ 81 #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_TEXT_BASE - \ 82 CONFIG_SYS_MALLOC_F_LEN) 83 84 /* 85 * CFI flash memory layout - Example 86 * CONFIG_SYS_FLASH_BASE = 0x2200_0000; 87 * CONFIG_SYS_FLASH_SIZE = 0x0080_0000; 8MB 88 * 89 * SECT_SIZE = 0x20000; 128kB is one sector 90 * CONFIG_ENV_SIZE = SECT_SIZE; 128kB environment store 91 * 92 * 0x2200_0000 CONFIG_SYS_FLASH_BASE 93 * FREE 256kB 94 * 0x2204_0000 CONFIG_ENV_ADDR 95 * ENV_AREA 128kB 96 * 0x2206_0000 97 * FREE 98 * 0x2280_0000 CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE 99 * 100 */ 101 102 #ifdef FLASH 103 # define CONFIG_SYS_FLASH_BASE XILINX_FLASH_START 104 # define CONFIG_SYS_FLASH_SIZE XILINX_FLASH_SIZE 105 # define CONFIG_SYS_FLASH_CFI 1 106 # define CONFIG_FLASH_CFI_DRIVER 1 107 /* ?empty sector */ 108 # define CONFIG_SYS_FLASH_EMPTY_INFO 1 109 /* max number of memory banks */ 110 # define CONFIG_SYS_MAX_FLASH_BANKS 1 111 /* max number of sectors on one chip */ 112 # define CONFIG_SYS_MAX_FLASH_SECT 512 113 /* hardware flash protection */ 114 # define CONFIG_SYS_FLASH_PROTECTION 115 /* use buffered writes (20x faster) */ 116 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 117 # ifdef RAMENV 118 # define CONFIG_ENV_IS_NOWHERE 1 119 # define CONFIG_ENV_SIZE 0x1000 120 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 121 122 # else /* FLASH && !RAMENV */ 123 # define CONFIG_ENV_IS_IN_FLASH 1 124 /* 128K(one sector) for env */ 125 # define CONFIG_ENV_SECT_SIZE 0x20000 126 # define CONFIG_ENV_ADDR \ 127 (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) 128 # define CONFIG_ENV_SIZE 0x20000 129 # endif /* FLASH && !RAMBOOT */ 130 #else /* !FLASH */ 131 132 #ifdef SPIFLASH 133 # define CONFIG_SYS_NO_FLASH 1 134 # define CONFIG_SYS_SPI_BASE XILINX_SPI_FLASH_BASEADDR 135 # define CONFIG_SPI 1 136 # define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 137 # define CONFIG_SF_DEFAULT_SPEED XILINX_SPI_FLASH_MAX_FREQ 138 # define CONFIG_SF_DEFAULT_CS XILINX_SPI_FLASH_CS 139 140 # ifdef RAMENV 141 # define CONFIG_ENV_IS_NOWHERE 1 142 # define CONFIG_ENV_SIZE 0x1000 143 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 144 145 # else /* SPIFLASH && !RAMENV */ 146 # define CONFIG_ENV_IS_IN_SPI_FLASH 1 147 # define CONFIG_ENV_SPI_MODE SPI_MODE_3 148 # define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED 149 # define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS 150 /* 128K(two sectors) for env */ 151 # define CONFIG_ENV_SECT_SIZE 0x10000 152 # define CONFIG_ENV_SIZE (2 * CONFIG_ENV_SECT_SIZE) 153 /* Warning: adjust the offset in respect of other flash content and size */ 154 # define CONFIG_ENV_OFFSET (128 * CONFIG_ENV_SECT_SIZE) /* at 8MB */ 155 # endif /* SPIFLASH && !RAMBOOT */ 156 #else /* !SPIFLASH */ 157 158 /* ENV in RAM */ 159 # define CONFIG_SYS_NO_FLASH 1 160 # define CONFIG_ENV_IS_NOWHERE 1 161 # define CONFIG_ENV_SIZE 0x1000 162 # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) 163 #endif /* !SPIFLASH */ 164 #endif /* !FLASH */ 165 166 /* system ace */ 167 #ifdef XILINX_SYSACE_BASEADDR 168 # define CONFIG_SYSTEMACE 169 /* #define DEBUG_SYSTEMACE */ 170 # define SYSTEMACE_CONFIG_FPGA 171 # define CONFIG_SYS_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR 172 # define CONFIG_SYS_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH 173 # define CONFIG_DOS_PARTITION 174 #endif 175 176 #if defined(XILINX_USE_ICACHE) 177 # define CONFIG_ICACHE 178 #else 179 # undef CONFIG_ICACHE 180 #endif 181 182 #if defined(XILINX_USE_DCACHE) 183 # define CONFIG_DCACHE 184 #else 185 # undef CONFIG_DCACHE 186 #endif 187 188 #ifndef XILINX_DCACHE_BYTE_SIZE 189 #define XILINX_DCACHE_BYTE_SIZE 32768 190 #endif 191 192 /* 193 * BOOTP options 194 */ 195 #define CONFIG_BOOTP_BOOTFILESIZE 196 #define CONFIG_BOOTP_BOOTPATH 197 #define CONFIG_BOOTP_GATEWAY 198 #define CONFIG_BOOTP_HOSTNAME 199 200 /* 201 * Command line configuration. 202 */ 203 #define CONFIG_CMD_ASKENV 204 #define CONFIG_CMD_IRQ 205 #define CONFIG_CMD_MFSL 206 207 #if defined(CONFIG_DCACHE) || defined(CONFIG_ICACHE) 208 # define CONFIG_CMD_CACHE 209 #else 210 # undef CONFIG_CMD_CACHE 211 #endif 212 213 #if defined(CONFIG_SYSTEMACE) 214 # define CONFIG_CMD_EXT2 215 # define CONFIG_CMD_FAT 216 #endif 217 218 #if defined(FLASH) 219 # define CONFIG_CMD_JFFS2 220 # define CONFIG_CMD_UBI 221 # undef CONFIG_CMD_UBIFS 222 223 # if !defined(RAMENV) 224 # define CONFIG_CMD_SAVES 225 # endif 226 227 #else 228 #if defined(SPIFLASH) 229 # define CONFIG_CMD_SF 230 231 # if !defined(RAMENV) 232 # define CONFIG_CMD_SAVES 233 # endif 234 #else 235 # undef CONFIG_CMD_JFFS2 236 # undef CONFIG_CMD_UBI 237 # undef CONFIG_CMD_UBIFS 238 #endif 239 #endif 240 241 #if defined(CONFIG_CMD_JFFS2) 242 # define CONFIG_MTD_PARTITIONS 243 #endif 244 245 #if defined(CONFIG_CMD_UBIFS) 246 # define CONFIG_CMD_UBI 247 # define CONFIG_LZO 248 #endif 249 250 #if defined(CONFIG_CMD_UBI) 251 # define CONFIG_MTD_PARTITIONS 252 # define CONFIG_RBTREE 253 #endif 254 255 #if defined(CONFIG_MTD_PARTITIONS) 256 /* MTD partitions */ 257 #define CONFIG_CMD_MTDPARTS /* mtdparts command line support */ 258 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ 259 #define CONFIG_FLASH_CFI_MTD 260 #define MTDIDS_DEFAULT "nor0=flash-0" 261 262 /* default mtd partition table */ 263 #define MTDPARTS_DEFAULT "mtdparts=flash-0:256k(u-boot),"\ 264 "256k(env),3m(kernel),1m(romfs),"\ 265 "1m(cramfs),-(jffs2)" 266 #endif 267 268 /* size of console buffer */ 269 #define CONFIG_SYS_CBSIZE 512 270 /* print buffer size */ 271 #define CONFIG_SYS_PBSIZE \ 272 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 273 /* max number of command args */ 274 #define CONFIG_SYS_MAXARGS 15 275 #define CONFIG_SYS_LONGHELP 276 /* default load address */ 277 #define CONFIG_SYS_LOAD_ADDR XILINX_RAM_START 278 279 #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ 280 #define CONFIG_BOOTARGS "root=romfs" 281 #define CONFIG_HOSTNAME XILINX_BOARD_NAME 282 #define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm" 283 #define CONFIG_IPADDR 192.168.0.3 284 #define CONFIG_SERVERIP 192.168.0.5 285 #define CONFIG_GATEWAYIP 192.168.0.1 286 287 /* architecture dependent code */ 288 #define CONFIG_SYS_USR_EXCEP /* user exception */ 289 290 #define CONFIG_PREBOOT "echo U-BOOT for ${hostname};setenv preboot;echo" 291 292 #define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" \ 293 "nor0=flash-0\0"\ 294 "mtdparts=mtdparts=flash-0:"\ 295 "256k(u-boot),256k(env),3m(kernel),"\ 296 "1m(romfs),1m(cramfs),-(jffs2)\0"\ 297 "nc=setenv stdout nc;"\ 298 "setenv stdin nc\0" \ 299 "serial=setenv stdout serial;"\ 300 "setenv stdin serial\0" 301 302 #define CONFIG_CMDLINE_EDITING 303 304 #define CONFIG_NETCONSOLE 305 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 306 307 /* Use the HUSH parser */ 308 #define CONFIG_SYS_HUSH_PARSER 309 310 /* Enable flat device tree support */ 311 #define CONFIG_LMB 1 312 #define CONFIG_FIT 1 313 #define CONFIG_OF_LIBFDT 1 314 315 #if defined(CONFIG_XILINX_AXIEMAC) 316 # define CONFIG_MII 1 317 # define CONFIG_CMD_MII 1 318 # define CONFIG_PHY_GIGE 1 319 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1 320 # define CONFIG_PHY_ATHEROS 1 321 # define CONFIG_PHY_BROADCOM 1 322 # define CONFIG_PHY_DAVICOM 1 323 # define CONFIG_PHY_LXT 1 324 # define CONFIG_PHY_MARVELL 1 325 # define CONFIG_PHY_MICREL 1 326 # define CONFIG_PHY_MICREL_KSZ9021 327 # define CONFIG_PHY_NATSEMI 1 328 # define CONFIG_PHY_REALTEK 1 329 # define CONFIG_PHY_VITESSE 1 330 #else 331 # undef CONFIG_MII 332 # undef CONFIG_CMD_MII 333 #endif 334 335 /* SPL part */ 336 #define CONFIG_CMD_SPL 337 #define CONFIG_SPL_FRAMEWORK 338 #define CONFIG_SPL_LIBCOMMON_SUPPORT 339 #define CONFIG_SPL_LIBGENERIC_SUPPORT 340 #define CONFIG_SPL_SERIAL_SUPPORT 341 #define CONFIG_SPL_BOARD_INIT 342 343 #define CONFIG_SPL_LDSCRIPT "arch/microblaze/cpu/u-boot-spl.lds" 344 345 #define CONFIG_SPL_RAM_DEVICE 346 #ifdef CONFIG_SYS_FLASH_BASE 347 # define CONFIG_SPL_NOR_SUPPORT 348 # define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_FLASH_BASE 349 #endif 350 351 /* for booting directly linux */ 352 #define CONFIG_SPL_OS_BOOT 353 354 #define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + \ 355 0x60000) 356 #define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \ 357 0x40000) 358 #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_TEXT_BASE + \ 359 0x1000000) 360 361 /* SP location before relocation, must use scratch RAM */ 362 /* BRAM start */ 363 #define CONFIG_SYS_INIT_RAM_ADDR 0x0 364 /* BRAM size - will be generated */ 365 #define CONFIG_SYS_INIT_RAM_SIZE 0x100000 366 367 # define CONFIG_SPL_STACK_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 368 CONFIG_SYS_INIT_RAM_SIZE - \ 369 CONFIG_SYS_MALLOC_F_LEN) 370 371 /* Just for sure that there is a space for stack */ 372 #define CONFIG_SPL_STACK_SIZE 0x100 373 374 #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE 375 376 #define CONFIG_SPL_MAX_FOOTPRINT (CONFIG_SYS_INIT_RAM_SIZE - \ 377 CONFIG_SYS_INIT_RAM_ADDR - \ 378 CONFIG_SYS_MALLOC_F_LEN - \ 379 CONFIG_SPL_STACK_SIZE) 380 381 #endif /* __CONFIG_H */ 382