1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2018 NXP 4 */ 5 6 #ifndef __LX2_RDB_H 7 #define __LX2_RDB_H 8 9 #include "lx2160a_common.h" 10 11 /* Qixis */ 12 #define QIXIS_XMAP_MASK 0x07 13 #define QIXIS_XMAP_SHIFT 5 14 #define QIXIS_RST_CTL_RESET_EN 0x30 15 #define QIXIS_LBMAP_DFLTBANK 0x00 16 #define QIXIS_LBMAP_ALTBANK 0x20 17 #define QIXIS_LBMAP_QSPI 0x00 18 #define QIXIS_RCW_SRC_QSPI 0xff 19 #define QIXIS_RST_CTL_RESET 0x31 20 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 21 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 22 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 23 #define QIXIS_LBMAP_MASK 0x0f 24 #define QIXIS_LBMAP_SD 25 #define QIXIS_RCW_SRC_SD 0x08 26 #define NON_EXTENDED_DUTCFG 27 28 /* VID */ 29 30 #define I2C_MUX_CH_VOL_MONITOR 0xA 31 /* Voltage monitor on channel 2*/ 32 #define I2C_VOL_MONITOR_ADDR 0x63 33 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 34 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 35 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 36 #define CONFIG_VID_FLS_ENV "lx2160ardb_vdd_mv" 37 #define CONFIG_VID 38 39 /* The lowest and highest voltage allowed*/ 40 #define VDD_MV_MIN 775 41 #define VDD_MV_MAX 855 42 43 /* PM Bus commands code for LTC3882*/ 44 #define PMBUS_CMD_PAGE 0x0 45 #define PMBUS_CMD_READ_VOUT 0x8B 46 #define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 47 #define PMBUS_CMD_VOUT_COMMAND 0x21 48 #define PWM_CHANNEL0 0x0 49 50 #define CONFIG_VOL_MONITOR_LTC3882_SET 51 #define CONFIG_VOL_MONITOR_LTC3882_READ 52 53 /* RTC */ 54 #define CONFIG_SYS_RTC_BUS_NUM 4 55 56 /* MAC/PHY configuration */ 57 #if defined(CONFIG_FSL_MC_ENET) 58 #define CONFIG_MII 59 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 60 61 #define AQR107_PHY_ADDR1 0x04 62 #define AQR107_PHY_ADDR2 0x05 63 64 #define CORTINA_NO_FW_UPLOAD 65 #define CORTINA_PHY_ADDR1 0x0 66 #define INPHI_PHY_ADDR1 0x0 67 68 #define RGMII_PHY_ADDR1 0x01 69 #define RGMII_PHY_ADDR2 0x02 70 71 #endif 72 73 /* EMC2305 */ 74 #define I2C_MUX_CH_EMC2305 0x09 75 #define I2C_EMC2305_ADDR 0x4D 76 #define I2C_EMC2305_CMD 0x40 77 #define I2C_EMC2305_PWM 0x80 78 79 /* EEPROM */ 80 #define CONFIG_ID_EEPROM 81 #define CONFIG_SYS_I2C_EEPROM_NXID 82 #define CONFIG_SYS_EEPROM_BUS_NUM 0 83 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 84 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 85 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 86 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 87 88 /* Initial environment variables */ 89 #define CONFIG_EXTRA_ENV_SETTINGS \ 90 EXTRA_ENV_SETTINGS \ 91 "lx2160ardb_vdd_mv=800\0" \ 92 "BOARD=lx2160ardb\0" \ 93 "xspi_bootcmd=echo Trying load from flexspi..;" \ 94 "sf probe 0:0 && sf read $load_addr " \ 95 "$kernel_start $kernel_size ; env exists secureboot &&" \ 96 "sf read $kernelheader_addr_r $kernelheader_start " \ 97 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ 98 " bootm $load_addr#$BOARD\0" \ 99 "sd_bootcmd=echo Trying load from sd card..;" \ 100 "mmcinfo; mmc read $load_addr " \ 101 "$kernel_addr_sd $kernel_size_sd ;" \ 102 "env exists secureboot && mmc read $kernelheader_addr_r "\ 103 "$kernelhdr_addr_sd $kernelhdr_size_sd " \ 104 " && esbc_validate ${kernelheader_addr_r};" \ 105 "bootm $load_addr#$BOARD\0" 106 107 #include <asm/fsl_secure_boot.h> 108 109 #endif /* __LX2_RDB_H */ 110