1 /* 2 * Copyright 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS2_RDB_H 8 #define __LS2_RDB_H 9 10 #include "ls2080a_common.h" 11 12 #undef CONFIG_CONS_INDEX 13 #define CONFIG_CONS_INDEX 2 14 15 #define I2C_MUX_CH_VOL_MONITOR 0xa 16 #define I2C_VOL_MONITOR_ADDR 0x38 17 #define CONFIG_VOL_MONITOR_IR36021_READ 18 #define CONFIG_VOL_MONITOR_IR36021_SET 19 20 #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" 21 #ifndef CONFIG_SPL_BUILD 22 #define CONFIG_VID 23 #endif 24 /* step the IR regulator in 5mV increments */ 25 #define IR_VDD_STEP_DOWN 5 26 #define IR_VDD_STEP_UP 5 27 /* The lowest and highest voltage allowed for LS2080ARDB */ 28 #define VDD_MV_MIN 819 29 #define VDD_MV_MAX 1212 30 31 #ifndef __ASSEMBLY__ 32 unsigned long get_board_sys_clk(void); 33 #endif 34 35 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 36 #define CONFIG_DDR_CLK_FREQ 133333333 37 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) 38 39 #define CONFIG_DDR_SPD 40 #define CONFIG_DDR_ECC 41 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 42 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 43 #define SPD_EEPROM_ADDRESS1 0x51 44 #define SPD_EEPROM_ADDRESS2 0x52 45 #define SPD_EEPROM_ADDRESS3 0x53 46 #define SPD_EEPROM_ADDRESS4 0x54 47 #define SPD_EEPROM_ADDRESS5 0x55 48 #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ 49 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 50 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 51 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 52 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 53 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 54 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 55 #endif 56 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 57 58 /* SATA */ 59 #define CONFIG_LIBATA 60 #define CONFIG_SCSI_AHCI 61 #define CONFIG_SCSI_AHCI_PLAT 62 #define CONFIG_SCSI 63 64 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 65 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 66 67 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 68 #define CONFIG_SYS_SCSI_MAX_LUN 1 69 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 70 CONFIG_SYS_SCSI_MAX_LUN) 71 72 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ 73 74 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 75 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 76 #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) 77 78 #define CONFIG_SYS_NOR0_CSPR \ 79 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 80 CSPR_PORT_SIZE_16 | \ 81 CSPR_MSEL_NOR | \ 82 CSPR_V) 83 #define CONFIG_SYS_NOR0_CSPR_EARLY \ 84 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ 85 CSPR_PORT_SIZE_16 | \ 86 CSPR_MSEL_NOR | \ 87 CSPR_V) 88 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) 89 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 90 FTIM0_NOR_TEADC(0x5) | \ 91 FTIM0_NOR_TEAHC(0x5)) 92 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 93 FTIM1_NOR_TRAD_NOR(0x1a) |\ 94 FTIM1_NOR_TSEQRAD_NOR(0x13)) 95 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 96 FTIM2_NOR_TCH(0x4) | \ 97 FTIM2_NOR_TWPH(0x0E) | \ 98 FTIM2_NOR_TWP(0x1c)) 99 #define CONFIG_SYS_NOR_FTIM3 0x04000000 100 #define CONFIG_SYS_IFC_CCR 0x01000000 101 102 #ifdef CONFIG_MTD_NOR_FLASH 103 #define CONFIG_FLASH_CFI_DRIVER 104 #define CONFIG_SYS_FLASH_CFI 105 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 106 #define CONFIG_SYS_FLASH_QUIET_TEST 107 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 108 109 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 110 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 111 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 112 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 113 114 #define CONFIG_SYS_FLASH_EMPTY_INFO 115 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ 116 CONFIG_SYS_FLASH_BASE + 0x40000000} 117 #endif 118 119 #define CONFIG_NAND_FSL_IFC 120 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 121 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 122 123 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) 124 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 125 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 126 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 127 | CSPR_V) 128 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 129 130 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 131 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 132 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 133 | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ 134 | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ 135 | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ 136 | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ 137 138 #define CONFIG_SYS_NAND_ONFI_DETECTION 139 140 /* ONFI NAND Flash mode0 Timing Params */ 141 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ 142 FTIM0_NAND_TWP(0x30) | \ 143 FTIM0_NAND_TWCHT(0x0e) | \ 144 FTIM0_NAND_TWH(0x14)) 145 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ 146 FTIM1_NAND_TWBE(0xab) | \ 147 FTIM1_NAND_TRR(0x1c) | \ 148 FTIM1_NAND_TRP(0x30)) 149 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ 150 FTIM2_NAND_TREH(0x14) | \ 151 FTIM2_NAND_TWHRE(0x3c)) 152 #define CONFIG_SYS_NAND_FTIM3 0x0 153 154 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 155 #define CONFIG_SYS_MAX_NAND_DEVICE 1 156 #define CONFIG_MTD_NAND_VERIFY_WRITE 157 #define CONFIG_CMD_NAND 158 159 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 160 161 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 162 #define QIXIS_LBMAP_SWITCH 0x06 163 #define QIXIS_LBMAP_MASK 0x0f 164 #define QIXIS_LBMAP_SHIFT 0 165 #define QIXIS_LBMAP_DFLTBANK 0x00 166 #define QIXIS_LBMAP_ALTBANK 0x04 167 #define QIXIS_LBMAP_NAND 0x09 168 #define QIXIS_RST_CTL_RESET 0x31 169 #define QIXIS_RST_CTL_RESET_EN 0x30 170 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 171 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 172 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 173 #define QIXIS_RCW_SRC_NAND 0x119 174 #define QIXIS_RST_FORCE_MEM 0x01 175 176 #define CONFIG_SYS_CSPR3_EXT (0x0) 177 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ 178 | CSPR_PORT_SIZE_8 \ 179 | CSPR_MSEL_GPCM \ 180 | CSPR_V) 181 #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 182 | CSPR_PORT_SIZE_8 \ 183 | CSPR_MSEL_GPCM \ 184 | CSPR_V) 185 186 #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) 187 #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) 188 /* QIXIS Timing parameters for IFC CS3 */ 189 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 190 FTIM0_GPCM_TEADC(0x0e) | \ 191 FTIM0_GPCM_TEAHC(0x0e)) 192 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 193 FTIM1_GPCM_TRAD(0x3f)) 194 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 195 FTIM2_GPCM_TCH(0xf) | \ 196 FTIM2_GPCM_TWP(0x3E)) 197 #define CONFIG_SYS_CS3_FTIM3 0x0 198 199 #if defined(CONFIG_SPL) && defined(CONFIG_NAND) 200 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 201 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY 202 #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR 203 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 204 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 205 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 206 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 207 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 208 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 209 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 210 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 211 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 212 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 213 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 214 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 215 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 216 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 217 218 #define CONFIG_ENV_IS_IN_NAND 219 #define CONFIG_ENV_OFFSET (2048 * 1024) 220 #define CONFIG_ENV_SECT_SIZE 0x20000 221 #define CONFIG_ENV_SIZE 0x2000 222 #define CONFIG_SPL_PAD_TO 0x80000 223 #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) 224 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) 225 #else 226 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 227 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY 228 #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR 229 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 230 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 231 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 232 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 233 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 234 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 235 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 236 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 237 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 238 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 239 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 240 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 241 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 242 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 243 244 #define CONFIG_ENV_IS_IN_FLASH 245 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000) 246 #define CONFIG_ENV_SECT_SIZE 0x20000 247 #define CONFIG_ENV_SIZE 0x2000 248 #endif 249 250 /* Debug Server firmware */ 251 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR 252 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL 253 254 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 255 256 /* 257 * I2C 258 */ 259 #define I2C_MUX_PCA_ADDR 0x75 260 #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ 261 262 /* I2C bus multiplexer */ 263 #define I2C_MUX_CH_DEFAULT 0x8 264 265 /* SPI */ 266 #ifdef CONFIG_FSL_DSPI 267 #define CONFIG_SPI_FLASH 268 #define CONFIG_SPI_FLASH_BAR 269 #define CONFIG_SPI_FLASH_STMICRO 270 #endif 271 272 /* 273 * RTC configuration 274 */ 275 #define RTC 276 #define CONFIG_RTC_DS3231 1 277 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 278 #define CONFIG_CMD_DATE 279 280 /* EEPROM */ 281 #define CONFIG_ID_EEPROM 282 #define CONFIG_CMD_EEPROM 283 #define CONFIG_SYS_I2C_EEPROM_NXID 284 #define CONFIG_SYS_EEPROM_BUS_NUM 0 285 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 286 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 287 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 288 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 289 290 #define CONFIG_FSL_MEMAC 291 292 #ifdef CONFIG_PCI 293 #define CONFIG_PCI_SCAN_SHOW 294 #define CONFIG_CMD_PCI 295 #endif 296 297 /* MMC */ 298 #ifdef CONFIG_MMC 299 #define CONFIG_FSL_ESDHC 300 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 301 #endif 302 303 #define CONFIG_MISC_INIT_R 304 305 /* 306 * USB 307 */ 308 #define CONFIG_HAS_FSL_XHCI_USB 309 #define CONFIG_USB_XHCI_FSL 310 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 311 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 312 313 #undef CONFIG_CMDLINE_EDITING 314 #include <config_distro_defaults.h> 315 316 #define BOOT_TARGET_DEVICES(func) \ 317 func(USB, usb, 0) \ 318 func(MMC, mmc, 0) \ 319 func(SCSI, scsi, 0) \ 320 func(DHCP, dhcp, na) 321 #include <config_distro_bootcmd.h> 322 323 /* Initial environment variables */ 324 #undef CONFIG_EXTRA_ENV_SETTINGS 325 #ifdef CONFIG_SECURE_BOOT 326 #define CONFIG_EXTRA_ENV_SETTINGS \ 327 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 328 "scriptaddr=0x80800000\0" \ 329 "kernel_addr_r=0x81000000\0" \ 330 "pxefile_addr_r=0x81000000\0" \ 331 "fdt_addr_r=0x88000000\0" \ 332 "ramdisk_addr_r=0x89000000\0" \ 333 "loadaddr=0x80100000\0" \ 334 "kernel_addr=0x100000\0" \ 335 "ramdisk_addr=0x800000\0" \ 336 "ramdisk_size=0x2000000\0" \ 337 "fdt_high=0xa0000000\0" \ 338 "initrd_high=0xffffffffffffffff\0" \ 339 "kernel_start=0x581100000\0" \ 340 "kernel_load=0xa0000000\0" \ 341 "kernel_size=0x2800000\0" \ 342 "fdtfile=fsl-ls2080a-rdb.dtb\0" \ 343 "mcinitcmd=esbc_validate 0x580c80000;" \ 344 "esbc_validate 0x580cc0000;" \ 345 "fsl_mc start mc 0x580300000" \ 346 " 0x580800000 \0" \ 347 BOOTENV 348 #else 349 #define CONFIG_EXTRA_ENV_SETTINGS \ 350 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 351 "scriptaddr=0x80800000\0" \ 352 "kernel_addr_r=0x81000000\0" \ 353 "pxefile_addr_r=0x81000000\0" \ 354 "fdt_addr_r=0x88000000\0" \ 355 "ramdisk_addr_r=0x89000000\0" \ 356 "loadaddr=0x80100000\0" \ 357 "kernel_addr=0x100000\0" \ 358 "ramdisk_addr=0x800000\0" \ 359 "ramdisk_size=0x2000000\0" \ 360 "fdt_high=0xa0000000\0" \ 361 "initrd_high=0xffffffffffffffff\0" \ 362 "kernel_start=0x581100000\0" \ 363 "kernel_load=0xa0000000\0" \ 364 "kernel_size=0x2800000\0" \ 365 "fdtfile=fsl-ls2080a-rdb.dtb\0" \ 366 "mcinitcmd=fsl_mc start mc 0x580300000" \ 367 " 0x580800000 \0" \ 368 BOOTENV 369 #endif 370 371 372 #undef CONFIG_BOOTARGS 373 #define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \ 374 "earlycon=uart8250,mmio,0x21c0600 " \ 375 "ramdisk_size=0x2000000 default_hugepagesz=2m" \ 376 " hugepagesz=2m hugepages=256" 377 378 #undef CONFIG_BOOTCOMMAND 379 /* Try to boot an on-NOR kernel first, then do normal distro boot */ 380 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \ 381 " && cp.b $kernel_start $kernel_load $kernel_size" \ 382 " && bootm $kernel_load" \ 383 " || run distro_bootcmd" 384 385 /* MAC/PHY configuration */ 386 #ifdef CONFIG_FSL_MC_ENET 387 #define CONFIG_PHYLIB_10G 388 #define CONFIG_PHY_AQUANTIA 389 #define CONFIG_PHY_CORTINA 390 #define CONFIG_PHYLIB 391 #define CONFIG_SYS_CORTINA_FW_IN_NOR 392 #define CONFIG_CORTINA_FW_ADDR 0x581000000 393 #define CONFIG_CORTINA_FW_LENGTH 0x40000 394 395 #define CORTINA_PHY_ADDR1 0x10 396 #define CORTINA_PHY_ADDR2 0x11 397 #define CORTINA_PHY_ADDR3 0x12 398 #define CORTINA_PHY_ADDR4 0x13 399 #define AQ_PHY_ADDR1 0x00 400 #define AQ_PHY_ADDR2 0x01 401 #define AQ_PHY_ADDR3 0x02 402 #define AQ_PHY_ADDR4 0x03 403 #define AQR405_IRQ_MASK 0x36 404 405 #define CONFIG_MII 406 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 407 #define CONFIG_PHY_GIGE 408 #define CONFIG_PHY_AQUANTIA 409 #endif 410 411 #include <asm/fsl_secure_boot.h> 412 413 #endif /* __LS2_RDB_H */ 414