xref: /openbmc/u-boot/include/configs/ls2080ardb.h (revision ced0d849)
1 /*
2  * Copyright 2015 Freescale Semiconductor
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS2_RDB_H
8 #define __LS2_RDB_H
9 
10 #include "ls2080a_common.h"
11 
12 #undef CONFIG_CONS_INDEX
13 #define CONFIG_CONS_INDEX       2
14 
15 #define CONFIG_DISPLAY_BOARDINFO
16 
17 #define I2C_MUX_CH_VOL_MONITOR		0xa
18 #define I2C_VOL_MONITOR_ADDR		0x38
19 #define CONFIG_VOL_MONITOR_IR36021_READ
20 #define CONFIG_VOL_MONITOR_IR36021_SET
21 
22 #define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
23 #ifndef CONFIG_SPL_BUILD
24 #define CONFIG_VID
25 #endif
26 /* step the IR regulator in 5mV increments */
27 #define IR_VDD_STEP_DOWN		5
28 #define IR_VDD_STEP_UP			5
29 /* The lowest and highest voltage allowed for LS2080ARDB */
30 #define VDD_MV_MIN			819
31 #define VDD_MV_MAX			1212
32 
33 #ifndef __ASSEMBLY__
34 unsigned long get_board_sys_clk(void);
35 #endif
36 
37 #define CONFIG_SYS_FSL_CLK
38 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
39 #define CONFIG_DDR_CLK_FREQ		133333333
40 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
41 
42 #define CONFIG_DDR_SPD
43 #define CONFIG_DDR_ECC
44 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
45 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
46 #define SPD_EEPROM_ADDRESS1	0x51
47 #define SPD_EEPROM_ADDRESS2	0x52
48 #define SPD_EEPROM_ADDRESS3	0x53
49 #define SPD_EEPROM_ADDRESS4	0x54
50 #define SPD_EEPROM_ADDRESS5	0x55
51 #define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
52 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
53 #define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
54 #define CONFIG_DIMM_SLOTS_PER_CTLR		2
55 #define CONFIG_CHIP_SELECTS_PER_CTRL		4
56 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
57 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
58 #endif
59 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
60 
61 /* SATA */
62 #define CONFIG_LIBATA
63 #define CONFIG_SCSI_AHCI
64 #define CONFIG_SCSI_AHCI_PLAT
65 #define CONFIG_CMD_SCSI
66 #define CONFIG_CMD_FAT
67 #define CONFIG_CMD_EXT2
68 #define CONFIG_DOS_PARTITION
69 #define CONFIG_BOARD_LATE_INIT
70 
71 #define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
72 #define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2
73 
74 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
75 #define CONFIG_SYS_SCSI_MAX_LUN			1
76 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
77 						CONFIG_SYS_SCSI_MAX_LUN)
78 
79 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
80 
81 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
82 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
83 #define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)
84 
85 #define CONFIG_SYS_NOR0_CSPR					\
86 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
87 	CSPR_PORT_SIZE_16					| \
88 	CSPR_MSEL_NOR						| \
89 	CSPR_V)
90 #define CONFIG_SYS_NOR0_CSPR_EARLY				\
91 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
92 	CSPR_PORT_SIZE_16					| \
93 	CSPR_MSEL_NOR						| \
94 	CSPR_V)
95 #define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
96 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
97 				FTIM0_NOR_TEADC(0x5) | \
98 				FTIM0_NOR_TEAHC(0x5))
99 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
100 				FTIM1_NOR_TRAD_NOR(0x1a) |\
101 				FTIM1_NOR_TSEQRAD_NOR(0x13))
102 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
103 				FTIM2_NOR_TCH(0x4) | \
104 				FTIM2_NOR_TWPH(0x0E) | \
105 				FTIM2_NOR_TWP(0x1c))
106 #define CONFIG_SYS_NOR_FTIM3	0x04000000
107 #define CONFIG_SYS_IFC_CCR	0x01000000
108 
109 #ifndef CONFIG_SYS_NO_FLASH
110 #define CONFIG_FLASH_CFI_DRIVER
111 #define CONFIG_SYS_FLASH_CFI
112 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
113 #define CONFIG_SYS_FLASH_QUIET_TEST
114 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
115 
116 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
117 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
118 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
119 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
120 
121 #define CONFIG_SYS_FLASH_EMPTY_INFO
122 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
123 					 CONFIG_SYS_FLASH_BASE + 0x40000000}
124 #endif
125 
126 #define CONFIG_NAND_FSL_IFC
127 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
128 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
129 
130 
131 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
132 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
133 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
134 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
135 				| CSPR_V)
136 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
137 
138 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
139 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
140 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
141 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
142 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
143 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
144 				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/
145 
146 #define CONFIG_SYS_NAND_ONFI_DETECTION
147 
148 /* ONFI NAND Flash mode0 Timing Params */
149 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
150 					FTIM0_NAND_TWP(0x30)   | \
151 					FTIM0_NAND_TWCHT(0x0e) | \
152 					FTIM0_NAND_TWH(0x14))
153 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
154 					FTIM1_NAND_TWBE(0xab)  | \
155 					FTIM1_NAND_TRR(0x1c)   | \
156 					FTIM1_NAND_TRP(0x30))
157 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
158 					FTIM2_NAND_TREH(0x14) | \
159 					FTIM2_NAND_TWHRE(0x3c))
160 #define CONFIG_SYS_NAND_FTIM3		0x0
161 
162 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
163 #define CONFIG_SYS_MAX_NAND_DEVICE	1
164 #define CONFIG_MTD_NAND_VERIFY_WRITE
165 #define CONFIG_CMD_NAND
166 
167 #define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
168 
169 #define CONFIG_FSL_QIXIS	/* use common QIXIS code */
170 #define QIXIS_LBMAP_SWITCH		0x06
171 #define QIXIS_LBMAP_MASK		0x0f
172 #define QIXIS_LBMAP_SHIFT		0
173 #define QIXIS_LBMAP_DFLTBANK		0x00
174 #define QIXIS_LBMAP_ALTBANK		0x04
175 #define QIXIS_LBMAP_NAND		0x09
176 #define QIXIS_RST_CTL_RESET		0x31
177 #define QIXIS_RST_CTL_RESET_EN		0x30
178 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
179 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
180 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
181 #define QIXIS_RCW_SRC_NAND		0x119
182 #define	QIXIS_RST_FORCE_MEM		0x01
183 
184 #define CONFIG_SYS_CSPR3_EXT	(0x0)
185 #define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
186 				| CSPR_PORT_SIZE_8 \
187 				| CSPR_MSEL_GPCM \
188 				| CSPR_V)
189 #define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
190 				| CSPR_PORT_SIZE_8 \
191 				| CSPR_MSEL_GPCM \
192 				| CSPR_V)
193 
194 #define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
195 #define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
196 /* QIXIS Timing parameters for IFC CS3 */
197 #define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
198 					FTIM0_GPCM_TEADC(0x0e) | \
199 					FTIM0_GPCM_TEAHC(0x0e))
200 #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
201 					FTIM1_GPCM_TRAD(0x3f))
202 #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
203 					FTIM2_GPCM_TCH(0xf) | \
204 					FTIM2_GPCM_TWP(0x3E))
205 #define CONFIG_SYS_CS3_FTIM3		0x0
206 
207 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
208 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
209 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
210 #define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
211 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
212 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
213 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
214 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
215 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
216 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
217 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
218 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
219 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
220 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
221 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
222 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
223 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
224 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
225 
226 #define CONFIG_ENV_IS_IN_NAND
227 #define CONFIG_ENV_OFFSET		(2048 * 1024)
228 #define CONFIG_ENV_SECT_SIZE		0x20000
229 #define CONFIG_ENV_SIZE			0x2000
230 #define CONFIG_SPL_PAD_TO		0x80000
231 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(1024 * 1024)
232 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
233 #else
234 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
235 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
236 #define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
237 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
238 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
239 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
240 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
241 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
242 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
243 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
244 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
245 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
246 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
247 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
248 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
249 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
250 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
251 
252 #define CONFIG_ENV_IS_IN_FLASH
253 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
254 #define CONFIG_ENV_SECT_SIZE		0x20000
255 #define CONFIG_ENV_SIZE			0x2000
256 #endif
257 
258 /* Debug Server firmware */
259 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
260 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR	0x580D00000ULL
261 
262 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
263 
264 /*
265  * I2C
266  */
267 #define I2C_MUX_PCA_ADDR		0x75
268 #define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/
269 
270 /* I2C bus multiplexer */
271 #define I2C_MUX_CH_DEFAULT      0x8
272 
273 /* SPI */
274 #ifdef CONFIG_FSL_DSPI
275 #define CONFIG_CMD_SF
276 #define CONFIG_SPI_FLASH
277 #define CONFIG_SPI_FLASH_BAR
278 #endif
279 
280 /*
281  * RTC configuration
282  */
283 #define RTC
284 #define CONFIG_RTC_DS3231               1
285 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
286 #define CONFIG_CMD_DATE
287 
288 /* EEPROM */
289 #define CONFIG_ID_EEPROM
290 #define CONFIG_CMD_EEPROM
291 #define CONFIG_SYS_I2C_EEPROM_NXID
292 #define CONFIG_SYS_EEPROM_BUS_NUM	0
293 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
294 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
295 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
296 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
297 
298 #define CONFIG_FSL_MEMAC
299 #define CONFIG_PCI		/* Enable PCIE */
300 #define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
301 
302 #ifdef CONFIG_PCI
303 #define CONFIG_PCI_PNP
304 #define CONFIG_PCI_SCAN_SHOW
305 #define CONFIG_CMD_PCI
306 #endif
307 
308 /*  MMC  */
309 #define CONFIG_MMC
310 #ifdef CONFIG_MMC
311 #define CONFIG_CMD_MMC
312 #define CONFIG_FSL_ESDHC
313 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
314 #define CONFIG_GENERIC_MMC
315 #define CONFIG_CMD_FAT
316 #define CONFIG_DOS_PARTITION
317 #endif
318 
319 #define CONFIG_MISC_INIT_R
320 
321 /*
322  * USB
323  */
324 #define CONFIG_HAS_FSL_XHCI_USB
325 #define CONFIG_USB_XHCI
326 #define CONFIG_USB_XHCI_FSL
327 #define CONFIG_USB_XHCI_DWC3
328 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
329 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
330 #define CONFIG_CMD_USB
331 #define CONFIG_USB_STORAGE
332 #define CONFIG_CMD_EXT2
333 
334 /* Initial environment variables */
335 #undef CONFIG_EXTRA_ENV_SETTINGS
336 #define CONFIG_EXTRA_ENV_SETTINGS		\
337 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
338 	"loadaddr=0x80100000\0"			\
339 	"kernel_addr=0x100000\0"		\
340 	"ramdisk_addr=0x800000\0"		\
341 	"ramdisk_size=0x2000000\0"		\
342 	"fdt_high=0xa0000000\0"			\
343 	"initrd_high=0xffffffffffffffff\0"	\
344 	"kernel_start=0x581100000\0"		\
345 	"kernel_load=0xa0000000\0"		\
346 	"kernel_size=0x2800000\0"		\
347 	"mcinitcmd=fsl_mc start mc 0x580300000"	\
348 	" 0x580800000 \0"
349 
350 #undef CONFIG_BOOTARGS
351 #define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
352 				"earlycon=uart8250,mmio,0x21c0600 " \
353 				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
354 				" hugepagesz=2m hugepages=256"
355 
356 /* MAC/PHY configuration */
357 #ifdef CONFIG_FSL_MC_ENET
358 #define CONFIG_PHYLIB_10G
359 #define CONFIG_PHY_AQUANTIA
360 #define CONFIG_PHY_CORTINA
361 #define CONFIG_PHYLIB
362 #define	CONFIG_SYS_CORTINA_FW_IN_NOR
363 #define CONFIG_CORTINA_FW_ADDR		0x581000000
364 #define CONFIG_CORTINA_FW_LENGTH	0x40000
365 
366 #define CORTINA_PHY_ADDR1	0x10
367 #define CORTINA_PHY_ADDR2	0x11
368 #define CORTINA_PHY_ADDR3	0x12
369 #define CORTINA_PHY_ADDR4	0x13
370 #define AQ_PHY_ADDR1		0x00
371 #define AQ_PHY_ADDR2		0x01
372 #define AQ_PHY_ADDR3		0x02
373 #define AQ_PHY_ADDR4		0x03
374 #define AQR405_IRQ_MASK		0x36
375 
376 #define CONFIG_MII
377 #define CONFIG_ETHPRIME		"DPNI1"
378 #define CONFIG_PHY_GIGE
379 #define CONFIG_PHY_AQUANTIA
380 #endif
381 
382 #include <asm/fsl_secure_boot.h>
383 
384 #endif /* __LS2_RDB_H */
385