1 /* 2 * Copyright 2017 NXP 3 * Copyright 2015 Freescale Semiconductor 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __LS2_RDB_H 9 #define __LS2_RDB_H 10 11 #include "ls2080a_common.h" 12 13 #undef CONFIG_CONS_INDEX 14 #define CONFIG_CONS_INDEX 2 15 16 #ifdef CONFIG_FSL_QSPI 17 #ifdef CONFIG_TARGET_LS2081ARDB 18 #define CONFIG_QIXIS_I2C_ACCESS 19 #endif 20 #define CONFIG_SYS_I2C_EARLY_INIT 21 #endif 22 23 #define I2C_MUX_CH_VOL_MONITOR 0xa 24 #define I2C_VOL_MONITOR_ADDR 0x38 25 #define CONFIG_VOL_MONITOR_IR36021_READ 26 #define CONFIG_VOL_MONITOR_IR36021_SET 27 28 #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" 29 #ifndef CONFIG_SPL_BUILD 30 #define CONFIG_VID 31 #endif 32 /* step the IR regulator in 5mV increments */ 33 #define IR_VDD_STEP_DOWN 5 34 #define IR_VDD_STEP_UP 5 35 /* The lowest and highest voltage allowed for LS2080ARDB */ 36 #define VDD_MV_MIN 819 37 #define VDD_MV_MAX 1212 38 39 #ifndef __ASSEMBLY__ 40 unsigned long get_board_sys_clk(void); 41 #endif 42 43 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 44 #define CONFIG_DDR_CLK_FREQ 133333333 45 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) 46 47 #define CONFIG_DDR_SPD 48 #define CONFIG_DDR_ECC 49 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 50 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 51 #define SPD_EEPROM_ADDRESS1 0x51 52 #define SPD_EEPROM_ADDRESS2 0x52 53 #define SPD_EEPROM_ADDRESS3 0x53 54 #define SPD_EEPROM_ADDRESS4 0x54 55 #define SPD_EEPROM_ADDRESS5 0x55 56 #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ 57 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 58 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 59 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 60 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 61 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 62 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 63 #endif 64 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 65 66 /* SATA */ 67 #define CONFIG_SCSI_AHCI_PLAT 68 69 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 70 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 71 72 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 73 #define CONFIG_SYS_SCSI_MAX_LUN 1 74 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 75 CONFIG_SYS_SCSI_MAX_LUN) 76 77 #ifndef CONFIG_FSL_QSPI 78 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ 79 80 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 81 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 82 #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) 83 84 #define CONFIG_SYS_NOR0_CSPR \ 85 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 86 CSPR_PORT_SIZE_16 | \ 87 CSPR_MSEL_NOR | \ 88 CSPR_V) 89 #define CONFIG_SYS_NOR0_CSPR_EARLY \ 90 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ 91 CSPR_PORT_SIZE_16 | \ 92 CSPR_MSEL_NOR | \ 93 CSPR_V) 94 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) 95 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 96 FTIM0_NOR_TEADC(0x5) | \ 97 FTIM0_NOR_TEAHC(0x5)) 98 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 99 FTIM1_NOR_TRAD_NOR(0x1a) |\ 100 FTIM1_NOR_TSEQRAD_NOR(0x13)) 101 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 102 FTIM2_NOR_TCH(0x4) | \ 103 FTIM2_NOR_TWPH(0x0E) | \ 104 FTIM2_NOR_TWP(0x1c)) 105 #define CONFIG_SYS_NOR_FTIM3 0x04000000 106 #define CONFIG_SYS_IFC_CCR 0x01000000 107 108 #ifdef CONFIG_MTD_NOR_FLASH 109 #define CONFIG_FLASH_CFI_DRIVER 110 #define CONFIG_SYS_FLASH_CFI 111 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 112 #define CONFIG_SYS_FLASH_QUIET_TEST 113 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 114 115 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 116 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 117 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 118 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 119 120 #define CONFIG_SYS_FLASH_EMPTY_INFO 121 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ 122 CONFIG_SYS_FLASH_BASE + 0x40000000} 123 #endif 124 125 #define CONFIG_NAND_FSL_IFC 126 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 127 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 128 129 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) 130 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 131 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 132 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 133 | CSPR_V) 134 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 135 136 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 137 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 138 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 139 | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ 140 | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ 141 | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ 142 | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ 143 144 #define CONFIG_SYS_NAND_ONFI_DETECTION 145 146 /* ONFI NAND Flash mode0 Timing Params */ 147 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ 148 FTIM0_NAND_TWP(0x30) | \ 149 FTIM0_NAND_TWCHT(0x0e) | \ 150 FTIM0_NAND_TWH(0x14)) 151 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ 152 FTIM1_NAND_TWBE(0xab) | \ 153 FTIM1_NAND_TRR(0x1c) | \ 154 FTIM1_NAND_TRP(0x30)) 155 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ 156 FTIM2_NAND_TREH(0x14) | \ 157 FTIM2_NAND_TWHRE(0x3c)) 158 #define CONFIG_SYS_NAND_FTIM3 0x0 159 160 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 161 #define CONFIG_SYS_MAX_NAND_DEVICE 1 162 #define CONFIG_MTD_NAND_VERIFY_WRITE 163 164 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 165 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 166 #define QIXIS_LBMAP_SWITCH 0x06 167 #define QIXIS_LBMAP_MASK 0x0f 168 #define QIXIS_LBMAP_SHIFT 0 169 #define QIXIS_LBMAP_DFLTBANK 0x00 170 #define QIXIS_LBMAP_ALTBANK 0x04 171 #define QIXIS_LBMAP_NAND 0x09 172 #define QIXIS_RST_CTL_RESET 0x31 173 #define QIXIS_RST_CTL_RESET_EN 0x30 174 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 175 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 176 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 177 #define QIXIS_RCW_SRC_NAND 0x119 178 #define QIXIS_RST_FORCE_MEM 0x01 179 180 #define CONFIG_SYS_CSPR3_EXT (0x0) 181 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ 182 | CSPR_PORT_SIZE_8 \ 183 | CSPR_MSEL_GPCM \ 184 | CSPR_V) 185 #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 186 | CSPR_PORT_SIZE_8 \ 187 | CSPR_MSEL_GPCM \ 188 | CSPR_V) 189 190 #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) 191 #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) 192 /* QIXIS Timing parameters for IFC CS3 */ 193 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 194 FTIM0_GPCM_TEADC(0x0e) | \ 195 FTIM0_GPCM_TEAHC(0x0e)) 196 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 197 FTIM1_GPCM_TRAD(0x3f)) 198 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 199 FTIM2_GPCM_TCH(0xf) | \ 200 FTIM2_GPCM_TWP(0x3E)) 201 #define CONFIG_SYS_CS3_FTIM3 0x0 202 203 #if defined(CONFIG_SPL) && defined(CONFIG_NAND) 204 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 205 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY 206 #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR 207 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 208 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 209 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 210 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 211 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 212 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 213 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 214 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 215 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 216 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 217 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 218 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 219 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 220 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 221 222 #define CONFIG_ENV_OFFSET (2048 * 1024) 223 #define CONFIG_ENV_SECT_SIZE 0x20000 224 #define CONFIG_ENV_SIZE 0x2000 225 #define CONFIG_SPL_PAD_TO 0x80000 226 #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) 227 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) 228 #else 229 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 230 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY 231 #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR 232 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 233 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 234 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 235 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 236 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 237 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 238 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 239 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 240 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 241 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 242 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 243 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 244 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 245 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 246 247 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) 248 #define CONFIG_ENV_SECT_SIZE 0x20000 249 #define CONFIG_ENV_SIZE 0x2000 250 #endif 251 252 /* Debug Server firmware */ 253 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR 254 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL 255 #endif 256 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 257 258 #ifdef CONFIG_TARGET_LS2081ARDB 259 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 260 #define QIXIS_QMAP_MASK 0x07 261 #define QIXIS_QMAP_SHIFT 5 262 #define QIXIS_LBMAP_DFLTBANK 0x00 263 #define QIXIS_LBMAP_QSPI 0x00 264 #define QIXIS_RCW_SRC_QSPI 0x62 265 #define QIXIS_LBMAP_ALTBANK 0x20 266 #define QIXIS_RST_CTL_RESET 0x31 267 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 268 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 269 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 270 #define QIXIS_LBMAP_MASK 0x0f 271 #define QIXIS_RST_CTL_RESET_EN 0x30 272 #endif 273 274 /* 275 * I2C 276 */ 277 #ifdef CONFIG_TARGET_LS2081ARDB 278 #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 279 #endif 280 #define I2C_MUX_PCA_ADDR 0x75 281 #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ 282 283 /* I2C bus multiplexer */ 284 #define I2C_MUX_CH_DEFAULT 0x8 285 286 /* SPI */ 287 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI) 288 #define CONFIG_SPI_FLASH 289 #ifdef CONFIG_FSL_DSPI 290 #define CONFIG_SPI_FLASH_STMICRO 291 #endif 292 #ifdef CONFIG_FSL_QSPI 293 #define CONFIG_SPI_FLASH_SPANSION 294 #endif 295 #define FSL_QSPI_FLASH_SIZE SZ_64M /* 64MB */ 296 #define FSL_QSPI_FLASH_NUM 2 297 #endif 298 299 /* 300 * RTC configuration 301 */ 302 #define RTC 303 #ifdef CONFIG_TARGET_LS2081ARDB 304 #define CONFIG_RTC_PCF8563 1 305 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 306 #else 307 #define CONFIG_RTC_DS3231 1 308 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 309 #endif 310 311 /* EEPROM */ 312 #define CONFIG_ID_EEPROM 313 #define CONFIG_SYS_I2C_EEPROM_NXID 314 #define CONFIG_SYS_EEPROM_BUS_NUM 0 315 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 316 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 317 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 318 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 319 320 #define CONFIG_FSL_MEMAC 321 322 #ifdef CONFIG_PCI 323 #define CONFIG_PCI_SCAN_SHOW 324 #endif 325 326 /* MMC */ 327 #ifdef CONFIG_MMC 328 #define CONFIG_FSL_ESDHC 329 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 330 #endif 331 332 #define CONFIG_MISC_INIT_R 333 334 #define BOOT_TARGET_DEVICES(func) \ 335 func(USB, usb, 0) \ 336 func(MMC, mmc, 0) \ 337 func(SCSI, scsi, 0) \ 338 func(DHCP, dhcp, na) 339 #include <config_distro_bootcmd.h> 340 341 #ifdef CONFIG_QSPI_BOOT 342 #define MC_INIT_CMD \ 343 "mcinitcmd=env exists secureboot && " \ 344 "esbc_validate 0x20700000 && " \ 345 "esbc_validate 0x20740000;" \ 346 "fsl_mc start mc 0x20a00000 0x20e00000 \0" 347 #elif defined(CONFIG_SD_BOOT) 348 #define MC_INIT_CMD \ 349 "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \ 350 "mmc read 0x80100000 0x7000 0x800;" \ 351 "env exists secureboot && " \ 352 "mmc read 0x80700000 0x3800 0x10 && " \ 353 "mmc read 0x80740000 0x3A00 0x10 && " \ 354 "esbc_validate 0x80700000 && " \ 355 "esbc_validate 0x80740000 ;" \ 356 "fsl_mc start mc 0x80000000 0x80100000\0" \ 357 "mcmemsize=0x70000000\0" 358 #else 359 #define MC_INIT_CMD \ 360 "mcinitcmd=env exists secureboot && " \ 361 "esbc_validate 0x580700000 && " \ 362 "esbc_validate 0x580740000; " \ 363 "fsl_mc start mc 0x580a00000 0x580e00000 \0" 364 #endif 365 366 /* Initial environment variables */ 367 #undef CONFIG_EXTRA_ENV_SETTINGS 368 #define CONFIG_EXTRA_ENV_SETTINGS \ 369 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 370 "ramdisk_addr=0x800000\0" \ 371 "ramdisk_size=0x2000000\0" \ 372 "fdt_high=0xa0000000\0" \ 373 "initrd_high=0xffffffffffffffff\0" \ 374 "fdt_addr=0x64f00000\0" \ 375 "kernel_addr=0x65000000\0" \ 376 "kernel_start=0x1000000\0" \ 377 "kernelheader_start=0x800000\0" \ 378 "scriptaddr=0x80000000\0" \ 379 "scripthdraddr=0x80080000\0" \ 380 "fdtheader_addr_r=0x80100000\0" \ 381 "kernelheader_addr_r=0x80200000\0" \ 382 "kernelheader_addr=0x580800000\0" \ 383 "kernel_addr_r=0x81000000\0" \ 384 "kernelheader_size=0x40000\0" \ 385 "fdt_addr_r=0x90000000\0" \ 386 "load_addr=0xa0000000\0" \ 387 "kernel_size=0x2800000\0" \ 388 "kernel_addr_sd=0x8000\0" \ 389 "kernel_size_sd=0x14000\0" \ 390 "console=ttyAMA0,38400n8\0" \ 391 "mcmemsize=0x70000000\0" \ 392 "sd_bootcmd=echo Trying load from SD ..;" \ 393 "mmcinfo; mmc read $load_addr " \ 394 "$kernel_addr_sd $kernel_size_sd && " \ 395 "bootm $load_addr#$board\0" \ 396 MC_INIT_CMD \ 397 BOOTENV \ 398 "boot_scripts=ls2088ardb_boot.scr\0" \ 399 "boot_script_hdr=hdr_ls2088ardb_bs.out\0" \ 400 "scan_dev_for_boot_part=" \ 401 "part list ${devtype} ${devnum} devplist; " \ 402 "env exists devplist || setenv devplist 1; " \ 403 "for distro_bootpart in ${devplist}; do " \ 404 "if fstype ${devtype} " \ 405 "${devnum}:${distro_bootpart} " \ 406 "bootfstype; then " \ 407 "run scan_dev_for_boot; " \ 408 "fi; " \ 409 "done\0" \ 410 "scan_dev_for_boot=" \ 411 "echo Scanning ${devtype} " \ 412 "${devnum}:${distro_bootpart}...; " \ 413 "for prefix in ${boot_prefixes}; do " \ 414 "run scan_dev_for_scripts; " \ 415 "done;\0" \ 416 "boot_a_script=" \ 417 "load ${devtype} ${devnum}:${distro_bootpart} " \ 418 "${scriptaddr} ${prefix}${script}; " \ 419 "env exists secureboot && load ${devtype} " \ 420 "${devnum}:${distro_bootpart} " \ 421 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 422 "&& esbc_validate ${scripthdraddr};" \ 423 "source ${scriptaddr}\0" \ 424 "qspi_bootcmd=echo Trying load from qspi..;" \ 425 "sf probe && sf read $load_addr " \ 426 "$kernel_start $kernel_size ; env exists secureboot &&" \ 427 "sf read $kernelheader_addr_r $kernelheader_start " \ 428 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ 429 " bootm $load_addr#$board\0" \ 430 "nor_bootcmd=echo Trying load from nor..;" \ 431 "cp.b $kernel_addr $load_addr " \ 432 "$kernel_size ; env exists secureboot && " \ 433 "cp.b $kernelheader_addr $kernelheader_addr_r " \ 434 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ 435 "bootm $load_addr#$board\0" 436 437 #undef CONFIG_BOOTCOMMAND 438 #ifdef CONFIG_QSPI_BOOT 439 /* Try to boot an on-QSPI kernel first, then do normal distro boot */ 440 #define CONFIG_BOOTCOMMAND \ 441 "env exists mcinitcmd && env exists secureboot "\ 442 "&& esbc_validate 0x20780000; " \ 443 "env exists mcinitcmd && " \ 444 "fsl_mc lazyapply dpl 0x20d00000; " \ 445 "run distro_bootcmd;env exists secureboot " \ 446 " && esbc_halt;run qspi_bootcmd; " 447 #elif defined(CONFIG_SD_BOOT) 448 /* Try to boot an on-SD kernel first, then do normal distro boot */ 449 #define CONFIG_BOOTCOMMAND \ 450 "env exists mcinitcmd && env exists secureboot "\ 451 "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \ 452 "&& esbc_validate $load_addr; " \ 453 "env exists mcinitcmd && run mcinitcmd " \ 454 "&& mmc read 0x88000000 0x6800 0x800 " \ 455 "&& fsl_mc lazyapply dpl 0x88000000; " \ 456 "run distro_bootcmd;env exists secureboot " \ 457 "&& esbc_halt;run sd_bootcmd;" 458 #else 459 /* Try to boot an on-NOR kernel first, then do normal distro boot */ 460 #define CONFIG_BOOTCOMMAND \ 461 "env exists mcinitcmd && env exists secureboot "\ 462 "&& esbc_validate 0x580780000; env exists mcinitcmd "\ 463 "&& fsl_mc lazyapply dpl 0x580d00000;" \ 464 "run distro_bootcmd; env exists secureboot " \ 465 "&& esbc_halt; run nor_bootcmd;" 466 #endif 467 468 /* MAC/PHY configuration */ 469 #ifdef CONFIG_FSL_MC_ENET 470 #define CONFIG_PHYLIB_10G 471 #define CONFIG_PHY_AQUANTIA 472 #define CONFIG_PHY_CORTINA 473 #define CONFIG_SYS_CORTINA_FW_IN_NOR 474 #ifdef CONFIG_QSPI_BOOT 475 #define CONFIG_CORTINA_FW_ADDR 0x20980000 476 #else 477 #define CONFIG_CORTINA_FW_ADDR 0x580980000 478 #endif 479 #define CONFIG_CORTINA_FW_LENGTH 0x40000 480 481 #define CORTINA_PHY_ADDR1 0x10 482 #define CORTINA_PHY_ADDR2 0x11 483 #define CORTINA_PHY_ADDR3 0x12 484 #define CORTINA_PHY_ADDR4 0x13 485 #define AQ_PHY_ADDR1 0x00 486 #define AQ_PHY_ADDR2 0x01 487 #define AQ_PHY_ADDR3 0x02 488 #define AQ_PHY_ADDR4 0x03 489 #define AQR405_IRQ_MASK 0x36 490 491 #define CONFIG_MII 492 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 493 #define CONFIG_PHY_AQUANTIA 494 #endif 495 496 #include <asm/fsl_secure_boot.h> 497 498 #endif /* __LS2_RDB_H */ 499