xref: /openbmc/u-boot/include/configs/ls2080ardb.h (revision 4349b55b)
1 /*
2  * Copyright 2015 Freescale Semiconductor
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS2_RDB_H
8 #define __LS2_RDB_H
9 
10 #include "ls2080a_common.h"
11 
12 #undef CONFIG_CONS_INDEX
13 #define CONFIG_CONS_INDEX       2
14 
15 #define CONFIG_DISPLAY_BOARDINFO
16 
17 #define I2C_MUX_CH_VOL_MONITOR		0xa
18 #define I2C_VOL_MONITOR_ADDR		0x38
19 #define CONFIG_VOL_MONITOR_IR36021_READ
20 #define CONFIG_VOL_MONITOR_IR36021_SET
21 
22 #define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
23 #ifndef CONFIG_SPL_BUILD
24 #define CONFIG_VID
25 #endif
26 /* step the IR regulator in 5mV increments */
27 #define IR_VDD_STEP_DOWN		5
28 #define IR_VDD_STEP_UP			5
29 /* The lowest and highest voltage allowed for LS2080ARDB */
30 #define VDD_MV_MIN			819
31 #define VDD_MV_MAX			1212
32 
33 #ifndef __ASSEMBLY__
34 unsigned long get_board_sys_clk(void);
35 #endif
36 
37 #define CONFIG_SYS_FSL_CLK
38 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
39 #define CONFIG_DDR_CLK_FREQ		133333333
40 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
41 
42 #define CONFIG_DDR_SPD
43 #define CONFIG_DDR_ECC
44 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
45 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
46 #define SPD_EEPROM_ADDRESS1	0x51
47 #define SPD_EEPROM_ADDRESS2	0x52
48 #define SPD_EEPROM_ADDRESS3	0x53
49 #define SPD_EEPROM_ADDRESS4	0x54
50 #define SPD_EEPROM_ADDRESS5	0x55
51 #define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
52 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
53 #define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
54 #define CONFIG_DIMM_SLOTS_PER_CTLR		2
55 #define CONFIG_CHIP_SELECTS_PER_CTRL		4
56 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
57 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
58 #endif
59 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
60 
61 /* SATA */
62 #define CONFIG_LIBATA
63 #define CONFIG_SCSI_AHCI
64 #define CONFIG_SCSI_AHCI_PLAT
65 #define CONFIG_SCSI
66 #define CONFIG_DOS_PARTITION
67 #define CONFIG_BOARD_LATE_INIT
68 
69 #define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
70 #define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2
71 
72 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
73 #define CONFIG_SYS_SCSI_MAX_LUN			1
74 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
75 						CONFIG_SYS_SCSI_MAX_LUN)
76 
77 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
78 
79 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
80 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
81 #define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)
82 
83 #define CONFIG_SYS_NOR0_CSPR					\
84 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
85 	CSPR_PORT_SIZE_16					| \
86 	CSPR_MSEL_NOR						| \
87 	CSPR_V)
88 #define CONFIG_SYS_NOR0_CSPR_EARLY				\
89 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
90 	CSPR_PORT_SIZE_16					| \
91 	CSPR_MSEL_NOR						| \
92 	CSPR_V)
93 #define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
94 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
95 				FTIM0_NOR_TEADC(0x5) | \
96 				FTIM0_NOR_TEAHC(0x5))
97 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
98 				FTIM1_NOR_TRAD_NOR(0x1a) |\
99 				FTIM1_NOR_TSEQRAD_NOR(0x13))
100 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
101 				FTIM2_NOR_TCH(0x4) | \
102 				FTIM2_NOR_TWPH(0x0E) | \
103 				FTIM2_NOR_TWP(0x1c))
104 #define CONFIG_SYS_NOR_FTIM3	0x04000000
105 #define CONFIG_SYS_IFC_CCR	0x01000000
106 
107 #ifndef CONFIG_SYS_NO_FLASH
108 #define CONFIG_FLASH_CFI_DRIVER
109 #define CONFIG_SYS_FLASH_CFI
110 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
111 #define CONFIG_SYS_FLASH_QUIET_TEST
112 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
113 
114 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
115 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
116 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
117 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
118 
119 #define CONFIG_SYS_FLASH_EMPTY_INFO
120 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
121 					 CONFIG_SYS_FLASH_BASE + 0x40000000}
122 #endif
123 
124 #define CONFIG_NAND_FSL_IFC
125 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
126 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
127 
128 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
129 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
130 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
131 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
132 				| CSPR_V)
133 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
134 
135 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
136 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
137 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
138 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
139 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
140 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
141 				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/
142 
143 #define CONFIG_SYS_NAND_ONFI_DETECTION
144 
145 /* ONFI NAND Flash mode0 Timing Params */
146 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
147 					FTIM0_NAND_TWP(0x30)   | \
148 					FTIM0_NAND_TWCHT(0x0e) | \
149 					FTIM0_NAND_TWH(0x14))
150 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
151 					FTIM1_NAND_TWBE(0xab)  | \
152 					FTIM1_NAND_TRR(0x1c)   | \
153 					FTIM1_NAND_TRP(0x30))
154 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
155 					FTIM2_NAND_TREH(0x14) | \
156 					FTIM2_NAND_TWHRE(0x3c))
157 #define CONFIG_SYS_NAND_FTIM3		0x0
158 
159 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
160 #define CONFIG_SYS_MAX_NAND_DEVICE	1
161 #define CONFIG_MTD_NAND_VERIFY_WRITE
162 #define CONFIG_CMD_NAND
163 
164 #define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
165 
166 #define CONFIG_FSL_QIXIS	/* use common QIXIS code */
167 #define QIXIS_LBMAP_SWITCH		0x06
168 #define QIXIS_LBMAP_MASK		0x0f
169 #define QIXIS_LBMAP_SHIFT		0
170 #define QIXIS_LBMAP_DFLTBANK		0x00
171 #define QIXIS_LBMAP_ALTBANK		0x04
172 #define QIXIS_LBMAP_NAND		0x09
173 #define QIXIS_RST_CTL_RESET		0x31
174 #define QIXIS_RST_CTL_RESET_EN		0x30
175 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
176 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
177 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
178 #define QIXIS_RCW_SRC_NAND		0x119
179 #define	QIXIS_RST_FORCE_MEM		0x01
180 
181 #define CONFIG_SYS_CSPR3_EXT	(0x0)
182 #define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
183 				| CSPR_PORT_SIZE_8 \
184 				| CSPR_MSEL_GPCM \
185 				| CSPR_V)
186 #define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
187 				| CSPR_PORT_SIZE_8 \
188 				| CSPR_MSEL_GPCM \
189 				| CSPR_V)
190 
191 #define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
192 #define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
193 /* QIXIS Timing parameters for IFC CS3 */
194 #define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
195 					FTIM0_GPCM_TEADC(0x0e) | \
196 					FTIM0_GPCM_TEAHC(0x0e))
197 #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
198 					FTIM1_GPCM_TRAD(0x3f))
199 #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
200 					FTIM2_GPCM_TCH(0xf) | \
201 					FTIM2_GPCM_TWP(0x3E))
202 #define CONFIG_SYS_CS3_FTIM3		0x0
203 
204 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
205 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
206 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
207 #define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
208 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
209 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
210 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
211 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
212 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
213 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
214 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
215 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
216 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
217 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
218 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
219 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
220 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
221 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
222 
223 #define CONFIG_ENV_IS_IN_NAND
224 #define CONFIG_ENV_OFFSET		(2048 * 1024)
225 #define CONFIG_ENV_SECT_SIZE		0x20000
226 #define CONFIG_ENV_SIZE			0x2000
227 #define CONFIG_SPL_PAD_TO		0x80000
228 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(1024 * 1024)
229 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
230 #else
231 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
232 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
233 #define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
234 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
235 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
236 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
237 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
238 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
239 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
240 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
241 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
242 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
243 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
244 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
245 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
246 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
247 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
248 
249 #define CONFIG_ENV_IS_IN_FLASH
250 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
251 #define CONFIG_ENV_SECT_SIZE		0x20000
252 #define CONFIG_ENV_SIZE			0x2000
253 #endif
254 
255 /* Debug Server firmware */
256 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
257 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR	0x580D00000ULL
258 
259 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
260 
261 /*
262  * I2C
263  */
264 #define I2C_MUX_PCA_ADDR		0x75
265 #define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/
266 
267 /* I2C bus multiplexer */
268 #define I2C_MUX_CH_DEFAULT      0x8
269 
270 /* SPI */
271 #ifdef CONFIG_FSL_DSPI
272 #define CONFIG_SPI_FLASH
273 #define CONFIG_SPI_FLASH_BAR
274 #endif
275 
276 /*
277  * RTC configuration
278  */
279 #define RTC
280 #define CONFIG_RTC_DS3231               1
281 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
282 #define CONFIG_CMD_DATE
283 
284 /* EEPROM */
285 #define CONFIG_ID_EEPROM
286 #define CONFIG_CMD_EEPROM
287 #define CONFIG_SYS_I2C_EEPROM_NXID
288 #define CONFIG_SYS_EEPROM_BUS_NUM	0
289 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
290 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
291 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
292 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
293 
294 #define CONFIG_FSL_MEMAC
295 #define CONFIG_PCI		/* Enable PCIE */
296 #define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
297 
298 #ifdef CONFIG_PCI
299 #define CONFIG_PCI_PNP
300 #define CONFIG_PCI_SCAN_SHOW
301 #define CONFIG_CMD_PCI
302 #endif
303 
304 /*  MMC  */
305 #define CONFIG_MMC
306 #ifdef CONFIG_MMC
307 #define CONFIG_FSL_ESDHC
308 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
309 #define CONFIG_GENERIC_MMC
310 #define CONFIG_DOS_PARTITION
311 #endif
312 
313 #define CONFIG_MISC_INIT_R
314 
315 /*
316  * USB
317  */
318 #define CONFIG_HAS_FSL_XHCI_USB
319 #define CONFIG_USB_XHCI
320 #define CONFIG_USB_XHCI_FSL
321 #define CONFIG_USB_XHCI_DWC3
322 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
323 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
324 #define CONFIG_USB_STORAGE
325 
326 /* Initial environment variables */
327 #undef CONFIG_EXTRA_ENV_SETTINGS
328 #define CONFIG_EXTRA_ENV_SETTINGS		\
329 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
330 	"loadaddr=0x80100000\0"			\
331 	"kernel_addr=0x100000\0"		\
332 	"ramdisk_addr=0x800000\0"		\
333 	"ramdisk_size=0x2000000\0"		\
334 	"fdt_high=0xa0000000\0"			\
335 	"initrd_high=0xffffffffffffffff\0"	\
336 	"kernel_start=0x581100000\0"		\
337 	"kernel_load=0xa0000000\0"		\
338 	"kernel_size=0x2800000\0"		\
339 	"mcinitcmd=fsl_mc start mc 0x580300000"	\
340 	" 0x580800000 \0"
341 
342 #undef CONFIG_BOOTARGS
343 #define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
344 				"earlycon=uart8250,mmio,0x21c0600 " \
345 				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
346 				" hugepagesz=2m hugepages=256"
347 
348 /* MAC/PHY configuration */
349 #ifdef CONFIG_FSL_MC_ENET
350 #define CONFIG_PHYLIB_10G
351 #define CONFIG_PHY_AQUANTIA
352 #define CONFIG_PHY_CORTINA
353 #define CONFIG_PHYLIB
354 #define	CONFIG_SYS_CORTINA_FW_IN_NOR
355 #define CONFIG_CORTINA_FW_ADDR		0x581000000
356 #define CONFIG_CORTINA_FW_LENGTH	0x40000
357 
358 #define CORTINA_PHY_ADDR1	0x10
359 #define CORTINA_PHY_ADDR2	0x11
360 #define CORTINA_PHY_ADDR3	0x12
361 #define CORTINA_PHY_ADDR4	0x13
362 #define AQ_PHY_ADDR1		0x00
363 #define AQ_PHY_ADDR2		0x01
364 #define AQ_PHY_ADDR3		0x02
365 #define AQ_PHY_ADDR4		0x03
366 #define AQR405_IRQ_MASK		0x36
367 
368 #define CONFIG_MII
369 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
370 #define CONFIG_PHY_GIGE
371 #define CONFIG_PHY_AQUANTIA
372 #endif
373 
374 #include <asm/fsl_secure_boot.h>
375 
376 #endif /* __LS2_RDB_H */
377