1 /* 2 * Copyright 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS2_RDB_H 8 #define __LS2_RDB_H 9 10 #include "ls2080a_common.h" 11 12 #undef CONFIG_CONS_INDEX 13 #define CONFIG_CONS_INDEX 2 14 15 #define I2C_MUX_CH_VOL_MONITOR 0xa 16 #define I2C_VOL_MONITOR_ADDR 0x38 17 #define CONFIG_VOL_MONITOR_IR36021_READ 18 #define CONFIG_VOL_MONITOR_IR36021_SET 19 20 #define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" 21 #ifndef CONFIG_SPL_BUILD 22 #define CONFIG_VID 23 #endif 24 /* step the IR regulator in 5mV increments */ 25 #define IR_VDD_STEP_DOWN 5 26 #define IR_VDD_STEP_UP 5 27 /* The lowest and highest voltage allowed for LS2080ARDB */ 28 #define VDD_MV_MIN 819 29 #define VDD_MV_MAX 1212 30 31 #ifndef __ASSEMBLY__ 32 unsigned long get_board_sys_clk(void); 33 #endif 34 35 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 36 #define CONFIG_DDR_CLK_FREQ 133333333 37 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) 38 39 #define CONFIG_DDR_SPD 40 #define CONFIG_DDR_ECC 41 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 42 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 43 #define SPD_EEPROM_ADDRESS1 0x51 44 #define SPD_EEPROM_ADDRESS2 0x52 45 #define SPD_EEPROM_ADDRESS3 0x53 46 #define SPD_EEPROM_ADDRESS4 0x54 47 #define SPD_EEPROM_ADDRESS5 0x55 48 #define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ 49 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 50 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 51 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 52 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 53 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 54 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 55 #endif 56 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 57 58 /* SATA */ 59 #define CONFIG_LIBATA 60 #define CONFIG_SCSI_AHCI 61 #define CONFIG_SCSI_AHCI_PLAT 62 #define CONFIG_SCSI 63 #define CONFIG_DOS_PARTITION 64 #define CONFIG_BOARD_LATE_INIT 65 66 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 67 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 68 69 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 70 #define CONFIG_SYS_SCSI_MAX_LUN 1 71 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 72 CONFIG_SYS_SCSI_MAX_LUN) 73 #define CONFIG_PARTITION_UUIDS 74 #define CONFIG_EFI_PARTITION 75 #define CONFIG_CMD_GPT 76 77 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */ 78 79 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 80 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) 81 #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) 82 83 #define CONFIG_SYS_NOR0_CSPR \ 84 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 85 CSPR_PORT_SIZE_16 | \ 86 CSPR_MSEL_NOR | \ 87 CSPR_V) 88 #define CONFIG_SYS_NOR0_CSPR_EARLY \ 89 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ 90 CSPR_PORT_SIZE_16 | \ 91 CSPR_MSEL_NOR | \ 92 CSPR_V) 93 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) 94 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 95 FTIM0_NOR_TEADC(0x5) | \ 96 FTIM0_NOR_TEAHC(0x5)) 97 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 98 FTIM1_NOR_TRAD_NOR(0x1a) |\ 99 FTIM1_NOR_TSEQRAD_NOR(0x13)) 100 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 101 FTIM2_NOR_TCH(0x4) | \ 102 FTIM2_NOR_TWPH(0x0E) | \ 103 FTIM2_NOR_TWP(0x1c)) 104 #define CONFIG_SYS_NOR_FTIM3 0x04000000 105 #define CONFIG_SYS_IFC_CCR 0x01000000 106 107 #ifndef CONFIG_SYS_NO_FLASH 108 #define CONFIG_FLASH_CFI_DRIVER 109 #define CONFIG_SYS_FLASH_CFI 110 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 111 #define CONFIG_SYS_FLASH_QUIET_TEST 112 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 113 114 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 115 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 116 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 117 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 118 119 #define CONFIG_SYS_FLASH_EMPTY_INFO 120 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ 121 CONFIG_SYS_FLASH_BASE + 0x40000000} 122 #endif 123 124 #define CONFIG_NAND_FSL_IFC 125 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 126 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 127 128 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) 129 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 130 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 131 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 132 | CSPR_V) 133 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 134 135 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 136 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 137 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 138 | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ 139 | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ 140 | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ 141 | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ 142 143 #define CONFIG_SYS_NAND_ONFI_DETECTION 144 145 /* ONFI NAND Flash mode0 Timing Params */ 146 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ 147 FTIM0_NAND_TWP(0x30) | \ 148 FTIM0_NAND_TWCHT(0x0e) | \ 149 FTIM0_NAND_TWH(0x14)) 150 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ 151 FTIM1_NAND_TWBE(0xab) | \ 152 FTIM1_NAND_TRR(0x1c) | \ 153 FTIM1_NAND_TRP(0x30)) 154 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ 155 FTIM2_NAND_TREH(0x14) | \ 156 FTIM2_NAND_TWHRE(0x3c)) 157 #define CONFIG_SYS_NAND_FTIM3 0x0 158 159 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 160 #define CONFIG_SYS_MAX_NAND_DEVICE 1 161 #define CONFIG_MTD_NAND_VERIFY_WRITE 162 #define CONFIG_CMD_NAND 163 164 #define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) 165 166 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 167 #define QIXIS_LBMAP_SWITCH 0x06 168 #define QIXIS_LBMAP_MASK 0x0f 169 #define QIXIS_LBMAP_SHIFT 0 170 #define QIXIS_LBMAP_DFLTBANK 0x00 171 #define QIXIS_LBMAP_ALTBANK 0x04 172 #define QIXIS_LBMAP_NAND 0x09 173 #define QIXIS_RST_CTL_RESET 0x31 174 #define QIXIS_RST_CTL_RESET_EN 0x30 175 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 176 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 177 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 178 #define QIXIS_RCW_SRC_NAND 0x119 179 #define QIXIS_RST_FORCE_MEM 0x01 180 181 #define CONFIG_SYS_CSPR3_EXT (0x0) 182 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ 183 | CSPR_PORT_SIZE_8 \ 184 | CSPR_MSEL_GPCM \ 185 | CSPR_V) 186 #define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 187 | CSPR_PORT_SIZE_8 \ 188 | CSPR_MSEL_GPCM \ 189 | CSPR_V) 190 191 #define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) 192 #define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) 193 /* QIXIS Timing parameters for IFC CS3 */ 194 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 195 FTIM0_GPCM_TEADC(0x0e) | \ 196 FTIM0_GPCM_TEAHC(0x0e)) 197 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 198 FTIM1_GPCM_TRAD(0x3f)) 199 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 200 FTIM2_GPCM_TCH(0xf) | \ 201 FTIM2_GPCM_TWP(0x3E)) 202 #define CONFIG_SYS_CS3_FTIM3 0x0 203 204 #if defined(CONFIG_SPL) && defined(CONFIG_NAND) 205 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 206 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY 207 #define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR 208 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 209 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 210 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 211 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 212 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 213 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 214 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 215 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 216 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 217 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 218 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 219 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 220 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 221 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 222 223 #define CONFIG_ENV_IS_IN_NAND 224 #define CONFIG_ENV_OFFSET (2048 * 1024) 225 #define CONFIG_ENV_SECT_SIZE 0x20000 226 #define CONFIG_ENV_SIZE 0x2000 227 #define CONFIG_SPL_PAD_TO 0x80000 228 #define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) 229 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) 230 #else 231 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 232 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY 233 #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR 234 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 235 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 236 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 237 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 238 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 239 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 240 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 241 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 242 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 243 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 244 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 245 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 246 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 247 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 248 249 #define CONFIG_ENV_IS_IN_FLASH 250 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000) 251 #define CONFIG_ENV_SECT_SIZE 0x20000 252 #define CONFIG_ENV_SIZE 0x2000 253 #endif 254 255 /* Debug Server firmware */ 256 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR 257 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL 258 259 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 260 261 /* 262 * I2C 263 */ 264 #define I2C_MUX_PCA_ADDR 0x75 265 #define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ 266 267 /* I2C bus multiplexer */ 268 #define I2C_MUX_CH_DEFAULT 0x8 269 270 /* SPI */ 271 #ifdef CONFIG_FSL_DSPI 272 #define CONFIG_SPI_FLASH 273 #define CONFIG_SPI_FLASH_BAR 274 #define CONFIG_SPI_FLASH_STMICRO 275 #endif 276 277 /* 278 * RTC configuration 279 */ 280 #define RTC 281 #define CONFIG_RTC_DS3231 1 282 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 283 #define CONFIG_CMD_DATE 284 285 /* EEPROM */ 286 #define CONFIG_ID_EEPROM 287 #define CONFIG_CMD_EEPROM 288 #define CONFIG_SYS_I2C_EEPROM_NXID 289 #define CONFIG_SYS_EEPROM_BUS_NUM 0 290 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 291 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 292 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 293 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 294 295 #define CONFIG_FSL_MEMAC 296 297 #ifdef CONFIG_PCI 298 #define CONFIG_PCI_SCAN_SHOW 299 #define CONFIG_CMD_PCI 300 #endif 301 302 /* MMC */ 303 #ifdef CONFIG_MMC 304 #define CONFIG_FSL_ESDHC 305 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 306 #define CONFIG_GENERIC_MMC 307 #define CONFIG_DOS_PARTITION 308 #endif 309 310 #define CONFIG_MISC_INIT_R 311 312 /* 313 * USB 314 */ 315 #define CONFIG_HAS_FSL_XHCI_USB 316 #define CONFIG_USB_XHCI_FSL 317 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 318 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 319 320 #undef CONFIG_CMDLINE_EDITING 321 #include <config_distro_defaults.h> 322 323 #define BOOT_TARGET_DEVICES(func) \ 324 func(USB, usb, 0) \ 325 func(MMC, mmc, 0) \ 326 func(SCSI, scsi, 0) \ 327 func(DHCP, dhcp, na) 328 #include <config_distro_bootcmd.h> 329 330 /* Initial environment variables */ 331 #undef CONFIG_EXTRA_ENV_SETTINGS 332 #ifdef CONFIG_SECURE_BOOT 333 #define CONFIG_EXTRA_ENV_SETTINGS \ 334 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 335 "scriptaddr=0x80800000\0" \ 336 "kernel_addr_r=0x81000000\0" \ 337 "pxefile_addr_r=0x81000000\0" \ 338 "fdt_addr_r=0x88000000\0" \ 339 "ramdisk_addr_r=0x89000000\0" \ 340 "loadaddr=0x80100000\0" \ 341 "kernel_addr=0x100000\0" \ 342 "ramdisk_addr=0x800000\0" \ 343 "ramdisk_size=0x2000000\0" \ 344 "fdt_high=0xa0000000\0" \ 345 "initrd_high=0xffffffffffffffff\0" \ 346 "kernel_start=0x581100000\0" \ 347 "kernel_load=0xa0000000\0" \ 348 "kernel_size=0x2800000\0" \ 349 "fdtfile=fsl-ls2080a-rdb.dtb\0" \ 350 "mcinitcmd=esbc_validate 0x580c80000;" \ 351 "esbc_validate 0x580cc0000;" \ 352 "fsl_mc start mc 0x580300000" \ 353 " 0x580800000 \0" \ 354 BOOTENV 355 #else 356 #define CONFIG_EXTRA_ENV_SETTINGS \ 357 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 358 "scriptaddr=0x80800000\0" \ 359 "kernel_addr_r=0x81000000\0" \ 360 "pxefile_addr_r=0x81000000\0" \ 361 "fdt_addr_r=0x88000000\0" \ 362 "ramdisk_addr_r=0x89000000\0" \ 363 "loadaddr=0x80100000\0" \ 364 "kernel_addr=0x100000\0" \ 365 "ramdisk_addr=0x800000\0" \ 366 "ramdisk_size=0x2000000\0" \ 367 "fdt_high=0xa0000000\0" \ 368 "initrd_high=0xffffffffffffffff\0" \ 369 "kernel_start=0x581100000\0" \ 370 "kernel_load=0xa0000000\0" \ 371 "kernel_size=0x2800000\0" \ 372 "fdtfile=fsl-ls2080a-rdb.dtb\0" \ 373 "mcinitcmd=fsl_mc start mc 0x580300000" \ 374 " 0x580800000 \0" \ 375 BOOTENV 376 #endif 377 378 379 #undef CONFIG_BOOTARGS 380 #define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \ 381 "earlycon=uart8250,mmio,0x21c0600 " \ 382 "ramdisk_size=0x2000000 default_hugepagesz=2m" \ 383 " hugepagesz=2m hugepages=256" 384 385 #undef CONFIG_BOOTCOMMAND 386 /* Try to boot an on-NOR kernel first, then do normal distro boot */ 387 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \ 388 " && cp.b $kernel_start $kernel_load $kernel_size" \ 389 " && bootm $kernel_load" \ 390 " || run distro_bootcmd" 391 392 /* MAC/PHY configuration */ 393 #ifdef CONFIG_FSL_MC_ENET 394 #define CONFIG_PHYLIB_10G 395 #define CONFIG_PHY_AQUANTIA 396 #define CONFIG_PHY_CORTINA 397 #define CONFIG_PHYLIB 398 #define CONFIG_SYS_CORTINA_FW_IN_NOR 399 #define CONFIG_CORTINA_FW_ADDR 0x581000000 400 #define CONFIG_CORTINA_FW_LENGTH 0x40000 401 402 #define CORTINA_PHY_ADDR1 0x10 403 #define CORTINA_PHY_ADDR2 0x11 404 #define CORTINA_PHY_ADDR3 0x12 405 #define CORTINA_PHY_ADDR4 0x13 406 #define AQ_PHY_ADDR1 0x00 407 #define AQ_PHY_ADDR2 0x01 408 #define AQ_PHY_ADDR3 0x02 409 #define AQ_PHY_ADDR4 0x03 410 #define AQR405_IRQ_MASK 0x36 411 412 #define CONFIG_MII 413 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 414 #define CONFIG_PHY_GIGE 415 #define CONFIG_PHY_AQUANTIA 416 #endif 417 418 #include <asm/fsl_secure_boot.h> 419 420 #endif /* __LS2_RDB_H */ 421