xref: /openbmc/u-boot/include/configs/ls2080ardb.h (revision 03bf9d58)
1 /*
2  * Copyright 2015 Freescale Semiconductor
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS2_RDB_H
8 #define __LS2_RDB_H
9 
10 #include "ls2080a_common.h"
11 
12 #undef CONFIG_CONS_INDEX
13 #define CONFIG_CONS_INDEX       2
14 
15 #define I2C_MUX_CH_VOL_MONITOR		0xa
16 #define I2C_VOL_MONITOR_ADDR		0x38
17 #define CONFIG_VOL_MONITOR_IR36021_READ
18 #define CONFIG_VOL_MONITOR_IR36021_SET
19 
20 #define CONFIG_VID_FLS_ENV		"ls2080ardb_vdd_mv"
21 #ifndef CONFIG_SPL_BUILD
22 #define CONFIG_VID
23 #endif
24 /* step the IR regulator in 5mV increments */
25 #define IR_VDD_STEP_DOWN		5
26 #define IR_VDD_STEP_UP			5
27 /* The lowest and highest voltage allowed for LS2080ARDB */
28 #define VDD_MV_MIN			819
29 #define VDD_MV_MAX			1212
30 
31 #ifndef __ASSEMBLY__
32 unsigned long get_board_sys_clk(void);
33 #endif
34 
35 #define CONFIG_SYS_FSL_CLK
36 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
37 #define CONFIG_DDR_CLK_FREQ		133333333
38 #define COUNTER_FREQUENCY_REAL		(CONFIG_SYS_CLK_FREQ/4)
39 
40 #define CONFIG_DDR_SPD
41 #define CONFIG_DDR_ECC
42 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
43 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
44 #define SPD_EEPROM_ADDRESS1	0x51
45 #define SPD_EEPROM_ADDRESS2	0x52
46 #define SPD_EEPROM_ADDRESS3	0x53
47 #define SPD_EEPROM_ADDRESS4	0x54
48 #define SPD_EEPROM_ADDRESS5	0x55
49 #define SPD_EEPROM_ADDRESS6	0x56	/* dummy address */
50 #define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
51 #define CONFIG_SYS_SPD_BUS_NUM	0	/* SPD on I2C bus 0 */
52 #define CONFIG_DIMM_SLOTS_PER_CTLR		2
53 #define CONFIG_CHIP_SELECTS_PER_CTRL		4
54 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
55 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR	1
56 #endif
57 #define CONFIG_FSL_DDR_BIST	/* enable built-in memory test */
58 
59 /* SATA */
60 #define CONFIG_LIBATA
61 #define CONFIG_SCSI_AHCI
62 #define CONFIG_SCSI_AHCI_PLAT
63 #define CONFIG_SCSI
64 #define CONFIG_DOS_PARTITION
65 #define CONFIG_BOARD_LATE_INIT
66 
67 #define CONFIG_SYS_SATA1			AHCI_BASE_ADDR1
68 #define CONFIG_SYS_SATA2			AHCI_BASE_ADDR2
69 
70 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
71 #define CONFIG_SYS_SCSI_MAX_LUN			1
72 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
73 						CONFIG_SYS_SCSI_MAX_LUN)
74 
75 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
76 
77 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
78 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128*1024*1024)
79 #define CONFIG_SYS_NOR_AMASK_EARLY	IFC_AMASK(64*1024*1024)
80 
81 #define CONFIG_SYS_NOR0_CSPR					\
82 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)		| \
83 	CSPR_PORT_SIZE_16					| \
84 	CSPR_MSEL_NOR						| \
85 	CSPR_V)
86 #define CONFIG_SYS_NOR0_CSPR_EARLY				\
87 	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)	| \
88 	CSPR_PORT_SIZE_16					| \
89 	CSPR_MSEL_NOR						| \
90 	CSPR_V)
91 #define CONFIG_SYS_NOR_CSOR	CSOR_NOR_ADM_SHIFT(12)
92 #define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
93 				FTIM0_NOR_TEADC(0x5) | \
94 				FTIM0_NOR_TEAHC(0x5))
95 #define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
96 				FTIM1_NOR_TRAD_NOR(0x1a) |\
97 				FTIM1_NOR_TSEQRAD_NOR(0x13))
98 #define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
99 				FTIM2_NOR_TCH(0x4) | \
100 				FTIM2_NOR_TWPH(0x0E) | \
101 				FTIM2_NOR_TWP(0x1c))
102 #define CONFIG_SYS_NOR_FTIM3	0x04000000
103 #define CONFIG_SYS_IFC_CCR	0x01000000
104 
105 #ifndef CONFIG_SYS_NO_FLASH
106 #define CONFIG_FLASH_CFI_DRIVER
107 #define CONFIG_SYS_FLASH_CFI
108 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
109 #define CONFIG_SYS_FLASH_QUIET_TEST
110 #define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
111 
112 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
113 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
114 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
115 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
116 
117 #define CONFIG_SYS_FLASH_EMPTY_INFO
118 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE,\
119 					 CONFIG_SYS_FLASH_BASE + 0x40000000}
120 #endif
121 
122 #define CONFIG_NAND_FSL_IFC
123 #define CONFIG_SYS_NAND_MAX_ECCPOS	256
124 #define CONFIG_SYS_NAND_MAX_OOBFREE	2
125 
126 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
127 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
128 				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
129 				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
130 				| CSPR_V)
131 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64 * 1024)
132 
133 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
134 				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
135 				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
136 				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
137 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
138 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
139 				| CSOR_NAND_PB(128))	/* Pages Per Block 128*/
140 
141 #define CONFIG_SYS_NAND_ONFI_DETECTION
142 
143 /* ONFI NAND Flash mode0 Timing Params */
144 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x0e) | \
145 					FTIM0_NAND_TWP(0x30)   | \
146 					FTIM0_NAND_TWCHT(0x0e) | \
147 					FTIM0_NAND_TWH(0x14))
148 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x64) | \
149 					FTIM1_NAND_TWBE(0xab)  | \
150 					FTIM1_NAND_TRR(0x1c)   | \
151 					FTIM1_NAND_TRP(0x30))
152 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x1e) | \
153 					FTIM2_NAND_TREH(0x14) | \
154 					FTIM2_NAND_TWHRE(0x3c))
155 #define CONFIG_SYS_NAND_FTIM3		0x0
156 
157 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
158 #define CONFIG_SYS_MAX_NAND_DEVICE	1
159 #define CONFIG_MTD_NAND_VERIFY_WRITE
160 #define CONFIG_CMD_NAND
161 
162 #define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
163 
164 #define CONFIG_FSL_QIXIS	/* use common QIXIS code */
165 #define QIXIS_LBMAP_SWITCH		0x06
166 #define QIXIS_LBMAP_MASK		0x0f
167 #define QIXIS_LBMAP_SHIFT		0
168 #define QIXIS_LBMAP_DFLTBANK		0x00
169 #define QIXIS_LBMAP_ALTBANK		0x04
170 #define QIXIS_LBMAP_NAND		0x09
171 #define QIXIS_RST_CTL_RESET		0x31
172 #define QIXIS_RST_CTL_RESET_EN		0x30
173 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
174 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
175 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
176 #define QIXIS_RCW_SRC_NAND		0x119
177 #define	QIXIS_RST_FORCE_MEM		0x01
178 
179 #define CONFIG_SYS_CSPR3_EXT	(0x0)
180 #define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
181 				| CSPR_PORT_SIZE_8 \
182 				| CSPR_MSEL_GPCM \
183 				| CSPR_V)
184 #define CONFIG_SYS_CSPR3_FINAL	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
185 				| CSPR_PORT_SIZE_8 \
186 				| CSPR_MSEL_GPCM \
187 				| CSPR_V)
188 
189 #define CONFIG_SYS_AMASK3	IFC_AMASK(64*1024)
190 #define CONFIG_SYS_CSOR3	CSOR_GPCM_ADM_SHIFT(12)
191 /* QIXIS Timing parameters for IFC CS3 */
192 #define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
193 					FTIM0_GPCM_TEADC(0x0e) | \
194 					FTIM0_GPCM_TEAHC(0x0e))
195 #define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
196 					FTIM1_GPCM_TRAD(0x3f))
197 #define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0xf) | \
198 					FTIM2_GPCM_TCH(0xf) | \
199 					FTIM2_GPCM_TWP(0x3E))
200 #define CONFIG_SYS_CS3_FTIM3		0x0
201 
202 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
203 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
204 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR_EARLY
205 #define CONFIG_SYS_CSPR2_FINAL		CONFIG_SYS_NOR0_CSPR
206 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
207 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
208 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
209 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
210 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
211 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
212 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
213 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
214 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
215 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
216 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
217 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
218 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
219 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
220 
221 #define CONFIG_ENV_IS_IN_NAND
222 #define CONFIG_ENV_OFFSET		(2048 * 1024)
223 #define CONFIG_ENV_SECT_SIZE		0x20000
224 #define CONFIG_ENV_SIZE			0x2000
225 #define CONFIG_SPL_PAD_TO		0x80000
226 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(1024 * 1024)
227 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 * 1024)
228 #else
229 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
230 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR_EARLY
231 #define CONFIG_SYS_CSPR0_FINAL		CONFIG_SYS_NOR0_CSPR
232 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
233 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
234 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
235 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
236 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
237 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
238 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
239 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
240 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
241 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
242 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
243 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
244 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
245 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
246 
247 #define CONFIG_ENV_IS_IN_FLASH
248 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
249 #define CONFIG_ENV_SECT_SIZE		0x20000
250 #define CONFIG_ENV_SIZE			0x2000
251 #endif
252 
253 /* Debug Server firmware */
254 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
255 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR	0x580D00000ULL
256 
257 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
258 
259 /*
260  * I2C
261  */
262 #define I2C_MUX_PCA_ADDR		0x75
263 #define I2C_MUX_PCA_ADDR_PRI		0x75 /* Primary Mux*/
264 
265 /* I2C bus multiplexer */
266 #define I2C_MUX_CH_DEFAULT      0x8
267 
268 /* SPI */
269 #ifdef CONFIG_FSL_DSPI
270 #define CONFIG_SPI_FLASH
271 #define CONFIG_SPI_FLASH_BAR
272 #endif
273 
274 /*
275  * RTC configuration
276  */
277 #define RTC
278 #define CONFIG_RTC_DS3231               1
279 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
280 #define CONFIG_CMD_DATE
281 
282 /* EEPROM */
283 #define CONFIG_ID_EEPROM
284 #define CONFIG_CMD_EEPROM
285 #define CONFIG_SYS_I2C_EEPROM_NXID
286 #define CONFIG_SYS_EEPROM_BUS_NUM	0
287 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
288 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
289 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
290 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
291 
292 #define CONFIG_FSL_MEMAC
293 #define CONFIG_PCI		/* Enable PCIE */
294 #define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
295 
296 #ifdef CONFIG_PCI
297 #define CONFIG_PCI_PNP
298 #define CONFIG_PCI_SCAN_SHOW
299 #define CONFIG_CMD_PCI
300 #endif
301 
302 /*  MMC  */
303 #define CONFIG_MMC
304 #ifdef CONFIG_MMC
305 #define CONFIG_FSL_ESDHC
306 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
307 #define CONFIG_GENERIC_MMC
308 #define CONFIG_DOS_PARTITION
309 #endif
310 
311 #define CONFIG_MISC_INIT_R
312 
313 /*
314  * USB
315  */
316 #define CONFIG_HAS_FSL_XHCI_USB
317 #define CONFIG_USB_XHCI_FSL
318 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
319 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
320 
321 /* Initial environment variables */
322 #undef CONFIG_EXTRA_ENV_SETTINGS
323 #define CONFIG_EXTRA_ENV_SETTINGS		\
324 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
325 	"loadaddr=0x80100000\0"			\
326 	"kernel_addr=0x100000\0"		\
327 	"ramdisk_addr=0x800000\0"		\
328 	"ramdisk_size=0x2000000\0"		\
329 	"fdt_high=0xa0000000\0"			\
330 	"initrd_high=0xffffffffffffffff\0"	\
331 	"kernel_start=0x581100000\0"		\
332 	"kernel_load=0xa0000000\0"		\
333 	"kernel_size=0x2800000\0"		\
334 	"mcinitcmd=fsl_mc start mc 0x580300000"	\
335 	" 0x580800000 \0"
336 
337 #undef CONFIG_BOOTARGS
338 #define CONFIG_BOOTARGS		"console=ttyS1,115200 root=/dev/ram0 " \
339 				"earlycon=uart8250,mmio,0x21c0600 " \
340 				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
341 				" hugepagesz=2m hugepages=256"
342 
343 /* MAC/PHY configuration */
344 #ifdef CONFIG_FSL_MC_ENET
345 #define CONFIG_PHYLIB_10G
346 #define CONFIG_PHY_AQUANTIA
347 #define CONFIG_PHY_CORTINA
348 #define CONFIG_PHYLIB
349 #define	CONFIG_SYS_CORTINA_FW_IN_NOR
350 #define CONFIG_CORTINA_FW_ADDR		0x581000000
351 #define CONFIG_CORTINA_FW_LENGTH	0x40000
352 
353 #define CORTINA_PHY_ADDR1	0x10
354 #define CORTINA_PHY_ADDR2	0x11
355 #define CORTINA_PHY_ADDR3	0x12
356 #define CORTINA_PHY_ADDR4	0x13
357 #define AQ_PHY_ADDR1		0x00
358 #define AQ_PHY_ADDR2		0x01
359 #define AQ_PHY_ADDR3		0x02
360 #define AQ_PHY_ADDR4		0x03
361 #define AQR405_IRQ_MASK		0x36
362 
363 #define CONFIG_MII
364 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
365 #define CONFIG_PHY_GIGE
366 #define CONFIG_PHY_AQUANTIA
367 #endif
368 
369 #include <asm/fsl_secure_boot.h>
370 
371 #endif /* __LS2_RDB_H */
372