1 /* 2 * Copyright 2017 NXP 3 * Copyright (C) 2014 Freescale Semiconductor 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __LS2_COMMON_H 9 #define __LS2_COMMON_H 10 11 #define CONFIG_REMAKE_ELF 12 #define CONFIG_FSL_LAYERSCAPE 13 #define CONFIG_MP 14 #define CONFIG_GICV3 15 #define CONFIG_FSL_TZPC_BP147 16 17 #include <asm/arch/stream_id_lsch3.h> 18 #include <asm/arch/config.h> 19 20 /* Link Definitions */ 21 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 22 23 /* We need architecture specific misc initializations */ 24 25 /* Link Definitions */ 26 #ifndef CONFIG_QSPI_BOOT 27 #ifdef CONFIG_SPL 28 #define CONFIG_SYS_TEXT_BASE 0x80400000 29 #else 30 #define CONFIG_SYS_TEXT_BASE 0x30100000 31 #endif 32 #else 33 #define CONFIG_SYS_TEXT_BASE 0x20100000 34 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 35 #define CONFIG_ENV_OFFSET 0x300000 /* 3MB */ 36 #define CONFIG_ENV_SECT_SIZE 0x40000 37 #endif 38 39 #define CONFIG_SUPPORT_RAW_INITRD 40 41 #define CONFIG_SKIP_LOWLEVEL_INIT 42 43 #ifndef CONFIG_SPL 44 #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ 45 #endif 46 #ifndef CONFIG_SYS_FSL_DDR4 47 #define CONFIG_SYS_DDR_RAW_TIMING 48 #endif 49 50 #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ 51 52 #define CONFIG_VERY_BIG_RAM 53 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 54 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 55 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 56 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL 57 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 58 59 /* 60 * SMP Definitinos 61 */ 62 #define CPU_RELEASE_ADDR secondary_boot_func 63 64 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS 65 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 66 #define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL 67 /* 68 * DDR controller use 0 as the base address for binding. 69 * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access. 70 */ 71 #define CONFIG_SYS_DP_DDR_BASE_PHY 0 72 #define CONFIG_DP_DDR_CTRL 2 73 #define CONFIG_DP_DDR_NUM_CTRLS 1 74 #endif 75 76 /* Generic Timer Definitions */ 77 /* 78 * This is not an accurate number. It is used in start.S. The frequency 79 * will be udpated later when get_bus_freq(0) is available. 80 */ 81 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 82 83 /* Size of malloc() pool */ 84 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) 85 86 /* I2C */ 87 #define CONFIG_SYS_I2C 88 #define CONFIG_SYS_I2C_MXC 89 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 90 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 91 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 92 #define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */ 93 94 /* Serial Port */ 95 #define CONFIG_CONS_INDEX 1 96 #define CONFIG_SYS_NS16550_SERIAL 97 #define CONFIG_SYS_NS16550_REG_SIZE 1 98 #define CONFIG_SYS_NS16550_CLK (get_serial_clock()) 99 100 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 101 102 /* IFC */ 103 #define CONFIG_FSL_IFC 104 105 /* 106 * During booting, IFC is mapped at the region of 0x30000000. 107 * But this region is limited to 256MB. To accommodate NOR, promjet 108 * and FPGA. This region is divided as below: 109 * 0x30000000 - 0x37ffffff : 128MB : NOR flash 110 * 0x38000000 - 0x3BFFFFFF : 64MB : Promjet 111 * 0x3C000000 - 0x40000000 : 64MB : FPGA etc 112 * 113 * To accommodate bigger NOR flash and other devices, we will map IFC 114 * chip selects to as below: 115 * 0x5_1000_0000..0x5_1fff_ffff Memory Hole 116 * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB) 117 * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB 118 * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet) 119 * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet) 120 * 121 * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation. 122 * CONFIG_SYS_FLASH_BASE has the final address (core view) 123 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) 124 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address 125 * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting 126 */ 127 128 #define CONFIG_SYS_FLASH_BASE 0x580000000ULL 129 #define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000 130 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 131 132 #define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000 133 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000 134 135 #ifndef __ASSEMBLY__ 136 unsigned long long get_qixis_addr(void); 137 #endif 138 #define QIXIS_BASE get_qixis_addr() 139 #define QIXIS_BASE_PHYS 0x20000000 140 #define QIXIS_BASE_PHYS_EARLY 0xC000000 141 #define QIXIS_STAT_PRES1 0xb 142 #define QIXIS_SDID_MASK 0x07 143 #define QIXIS_ESDHC_NO_ADAPTER 0x7 144 145 #define CONFIG_SYS_NAND_BASE 0x530000000ULL 146 #define CONFIG_SYS_NAND_BASE_PHYS 0x30000000 147 148 /* MC firmware */ 149 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */ 150 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 151 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 152 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 153 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 154 /* For LS2085A */ 155 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000 156 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000 157 158 /* Define phy_reset function to boot the MC based on mcinitcmd. 159 * This happens late enough to properly fixup u-boot env MAC addresses. 160 */ 161 #define CONFIG_RESET_PHY_R 162 163 /* 164 * Carve out a DDR region which will not be used by u-boot/Linux 165 * 166 * It will be used by MC and Debug Server. The MC region must be 167 * 512MB aligned, so the min size to hide is 512MB. 168 */ 169 #ifdef CONFIG_FSL_MC_ENET 170 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024) 171 #endif 172 173 /* Command line configuration */ 174 175 /* Miscellaneous configurable options */ 176 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 177 178 /* Physical Memory Map */ 179 /* fixme: these need to be checked against the board */ 180 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 181 182 #define CONFIG_NR_DRAM_BANKS 3 183 184 #define CONFIG_HWCONFIG 185 #define HWCONFIG_BUFFER_SIZE 128 186 187 /* Allow to overwrite serial and ethaddr */ 188 #define CONFIG_ENV_OVERWRITE 189 190 /* Initial environment variables */ 191 #define CONFIG_EXTRA_ENV_SETTINGS \ 192 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 193 "loadaddr=0x80100000\0" \ 194 "kernel_addr=0x100000\0" \ 195 "ramdisk_addr=0x800000\0" \ 196 "ramdisk_size=0x2000000\0" \ 197 "fdt_high=0xa0000000\0" \ 198 "initrd_high=0xffffffffffffffff\0" \ 199 "kernel_start=0x581000000\0" \ 200 "kernel_load=0xa0000000\0" \ 201 "kernel_size=0x2800000\0" \ 202 "console=ttyAMA0,38400n8\0" \ 203 "mcinitcmd=fsl_mc start mc 0x580a00000" \ 204 " 0x580e00000 \0" 205 206 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ 207 "earlycon=uart8250,mmio,0x21c0500 " \ 208 "ramdisk_size=0x2000000 default_hugepagesz=2m" \ 209 " hugepagesz=2m hugepages=256" 210 #ifdef CONFIG_SD_BOOT 211 #define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\ 212 " fsl_mc apply dpl 0x80200000 &&" \ 213 " mmc read $kernel_load $kernel_start" \ 214 " $kernel_size && bootm $kernel_load" 215 #else 216 #define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \ 217 " cp.b $kernel_start $kernel_load" \ 218 " $kernel_size && bootm $kernel_load" 219 #endif 220 221 /* Monitor Command Prompt */ 222 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 223 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 224 sizeof(CONFIG_SYS_PROMPT) + 16) 225 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 226 #define CONFIG_SYS_LONGHELP 227 #define CONFIG_CMDLINE_EDITING 1 228 #define CONFIG_AUTO_COMPLETE 229 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 230 231 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 232 233 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 234 #define CONFIG_SPL_BSS_MAX_SIZE 0x00100000 235 #define CONFIG_SPL_FRAMEWORK 236 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" 237 #define CONFIG_SPL_MAX_SIZE 0x16000 238 #define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0) 239 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 240 #define CONFIG_SPL_TEXT_BASE 0x1800a000 241 242 #ifdef CONFIG_NAND_BOOT 243 #define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000 244 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST 245 #endif 246 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000 247 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 248 #define CONFIG_SYS_MONITOR_LEN (640 * 1024) 249 250 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 251 252 #include <asm/arch/soc.h> 253 254 #endif /* __LS2_COMMON_H */ 255