1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2017 NXP
4  * Copyright (C) 2014 Freescale Semiconductor
5  */
6 
7 #ifndef __LS2_COMMON_H
8 #define __LS2_COMMON_H
9 
10 #define CONFIG_REMAKE_ELF
11 #define CONFIG_FSL_LAYERSCAPE
12 #define CONFIG_GICV3
13 #define CONFIG_FSL_TZPC_BP147
14 
15 #include <asm/arch/stream_id_lsch3.h>
16 #include <asm/arch/config.h>
17 
18 /* Link Definitions */
19 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
20 
21 /* We need architecture specific misc initializations */
22 
23 /* Link Definitions */
24 #ifndef CONFIG_QSPI_BOOT
25 #else
26 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
27 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
28 #define CONFIG_ENV_SECT_SIZE		0x40000
29 #endif
30 
31 #define CONFIG_SKIP_LOWLEVEL_INIT
32 
33 #ifndef CONFIG_SPL
34 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
35 #endif
36 #ifndef CONFIG_SYS_FSL_DDR4
37 #define CONFIG_SYS_DDR_RAW_TIMING
38 #endif
39 
40 #define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */
41 
42 #define CONFIG_VERY_BIG_RAM
43 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
44 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
45 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
46 #define CONFIG_SYS_DDR_BLOCK2_BASE	0x8080000000ULL
47 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	2
48 
49 /*
50  * SMP Definitinos
51  */
52 #define CPU_RELEASE_ADDR		secondary_boot_func
53 
54 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
55 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
56 #define CONFIG_SYS_DP_DDR_BASE		0x6000000000ULL
57 /*
58  * DDR controller use 0 as the base address for binding.
59  * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
60  */
61 #define CONFIG_SYS_DP_DDR_BASE_PHY	0
62 #define CONFIG_DP_DDR_CTRL		2
63 #define CONFIG_DP_DDR_NUM_CTRLS		1
64 #endif
65 
66 /* Generic Timer Definitions */
67 /*
68  * This is not an accurate number. It is used in start.S. The frequency
69  * will be udpated later when get_bus_freq(0) is available.
70  */
71 #define COUNTER_FREQUENCY		25000000	/* 25MHz */
72 
73 /* Size of malloc() pool */
74 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)
75 
76 /* I2C */
77 #define CONFIG_SYS_I2C
78 
79 /* Serial Port */
80 #define CONFIG_SYS_NS16550_SERIAL
81 #define CONFIG_SYS_NS16550_REG_SIZE     1
82 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
83 
84 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
85 
86 /* IFC */
87 #define CONFIG_FSL_IFC
88 
89 /*
90  * During booting, IFC is mapped at the region of 0x30000000.
91  * But this region is limited to 256MB. To accommodate NOR, promjet
92  * and FPGA. This region is divided as below:
93  * 0x30000000 - 0x37ffffff : 128MB : NOR flash
94  * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
95  * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
96  *
97  * To accommodate bigger NOR flash and other devices, we will map IFC
98  * chip selects to as below:
99  * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
100  * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
101  * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
102  * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
103  * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
104  *
105  * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
106  * CONFIG_SYS_FLASH_BASE has the final address (core view)
107  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
108  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
109  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
110  */
111 
112 #define CONFIG_SYS_FLASH_BASE			0x580000000ULL
113 #define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
114 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
115 
116 #define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
117 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000
118 
119 #ifndef __ASSEMBLY__
120 unsigned long long get_qixis_addr(void);
121 #endif
122 #define QIXIS_BASE				get_qixis_addr()
123 #define QIXIS_BASE_PHYS				0x20000000
124 #define QIXIS_BASE_PHYS_EARLY			0xC000000
125 #define QIXIS_STAT_PRES1			0xb
126 #define QIXIS_SDID_MASK				0x07
127 #define QIXIS_ESDHC_NO_ADAPTER			0x7
128 
129 #define CONFIG_SYS_NAND_BASE			0x530000000ULL
130 #define CONFIG_SYS_NAND_BASE_PHYS		0x30000000
131 
132 /* MC firmware */
133 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
134 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
135 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
136 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
137 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
138 /* For LS2085A */
139 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
140 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000
141 
142 /* Define phy_reset function to boot the MC based on mcinitcmd.
143  * This happens late enough to properly fixup u-boot env MAC addresses.
144  */
145 #define CONFIG_RESET_PHY_R
146 
147 /*
148  * Carve out a DDR region which will not be used by u-boot/Linux
149  *
150  * It will be used by MC and Debug Server. The MC region must be
151  * 512MB aligned, so the min size to hide is 512MB.
152  */
153 #ifdef CONFIG_FSL_MC_ENET
154 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(512UL * 1024 * 1024)
155 #endif
156 
157 /* Command line configuration */
158 
159 /* Miscellaneous configurable options */
160 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
161 
162 /* Physical Memory Map */
163 /* fixme: these need to be checked against the board */
164 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
165 
166 #define CONFIG_NR_DRAM_BANKS		3
167 
168 #define CONFIG_HWCONFIG
169 #define HWCONFIG_BUFFER_SIZE		128
170 
171 /* Allow to overwrite serial and ethaddr */
172 #define CONFIG_ENV_OVERWRITE
173 
174 /* Initial environment variables */
175 #define CONFIG_EXTRA_ENV_SETTINGS		\
176 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
177 	"loadaddr=0x80100000\0"			\
178 	"kernel_addr=0x100000\0"		\
179 	"ramdisk_addr=0x800000\0"		\
180 	"ramdisk_size=0x2000000\0"		\
181 	"fdt_high=0xa0000000\0"			\
182 	"initrd_high=0xffffffffffffffff\0"	\
183 	"kernel_start=0x581000000\0"		\
184 	"kernel_load=0xa0000000\0"		\
185 	"kernel_size=0x2800000\0"		\
186 	"console=ttyAMA0,38400n8\0"		\
187 	"mcinitcmd=fsl_mc start mc 0x580a00000"	\
188 	" 0x580e00000 \0"
189 
190 #ifdef CONFIG_SD_BOOT
191 #define CONFIG_BOOTCOMMAND	"mmc read 0x80200000 0x6800 0x800;"\
192 				" fsl_mc apply dpl 0x80200000 &&" \
193 				" mmc read $kernel_load $kernel_start" \
194 				" $kernel_size && bootm $kernel_load"
195 #else
196 #define CONFIG_BOOTCOMMAND	"fsl_mc apply dpl 0x580d00000 &&" \
197 				" cp.b $kernel_start $kernel_load" \
198 				" $kernel_size && bootm $kernel_load"
199 #endif
200 
201 /* Monitor Command Prompt */
202 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
203 #define CONFIG_SYS_MAXARGS		64	/* max command args */
204 
205 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
206 #define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
207 #define CONFIG_SPL_MAX_SIZE		0x16000
208 #define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
209 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
210 #define CONFIG_SPL_TEXT_BASE		0x1800a000
211 
212 #ifdef CONFIG_NAND_BOOT
213 #define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
214 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
215 #endif
216 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
217 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
218 #define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)
219 
220 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
221 
222 #include <asm/arch/soc.h>
223 
224 #endif /* __LS2_COMMON_H */
225