1 /* 2 * Copyright 2017 NXP 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS1088A_RDB_H 8 #define __LS1088A_RDB_H 9 10 #include "ls1088a_common.h" 11 12 #ifndef SPL_NO_BOARDINFO 13 #define CONFIG_DISPLAY_BOARDINFO_LATE 14 #endif 15 16 #define CONFIG_MISC_INIT_R 17 18 #if defined(CONFIG_QSPI_BOOT) 19 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 20 #define CONFIG_ENV_SECT_SIZE 0x40000 21 #elif defined(CONFIG_SD_BOOT) 22 #define CONFIG_ENV_OFFSET (3 * 1024 * 1024) 23 #define CONFIG_SYS_MMC_ENV_DEV 0 24 #define CONFIG_ENV_SIZE 0x2000 25 #else 26 #define CONFIG_ENV_IS_IN_FLASH 27 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) 28 #define CONFIG_ENV_SECT_SIZE 0x20000 29 #define CONFIG_ENV_SIZE 0x20000 30 #endif 31 32 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 33 #ifndef CONFIG_SPL_BUILD 34 #define CONFIG_QIXIS_I2C_ACCESS 35 #endif 36 #define SYS_NO_FLASH 37 #undef CONFIG_CMD_IMLS 38 #endif 39 40 #define CONFIG_SYS_CLK_FREQ 100000000 41 #define CONFIG_DDR_CLK_FREQ 100000000 42 #define COUNTER_FREQUENCY_REAL 25000000 /* 25MHz */ 43 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 44 45 #define CONFIG_DDR_SPD 46 #ifdef CONFIG_EMU 47 #define CONFIG_SYS_FSL_DDR_EMU 48 #define CONFIG_SYS_MXC_I2C1_SPEED 40000000 49 #define CONFIG_SYS_MXC_I2C2_SPEED 40000000 50 #else 51 #define CONFIG_DDR_ECC 52 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 53 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 54 #endif 55 #define SPD_EEPROM_ADDRESS 0x51 56 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 57 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 58 59 60 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 61 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 62 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 63 #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64 * 1024 * 1024) 64 65 #define CONFIG_SYS_NOR0_CSPR \ 66 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 67 CSPR_PORT_SIZE_16 | \ 68 CSPR_MSEL_NOR | \ 69 CSPR_V) 70 #define CONFIG_SYS_NOR0_CSPR_EARLY \ 71 (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ 72 CSPR_PORT_SIZE_16 | \ 73 CSPR_MSEL_NOR | \ 74 CSPR_V) 75 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(6) 76 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \ 77 FTIM0_NOR_TEADC(0x1) | \ 78 FTIM0_NOR_TEAHC(0x1)) 79 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \ 80 FTIM1_NOR_TRAD_NOR(0x1)) 81 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) | \ 82 FTIM2_NOR_TCH(0x0) | \ 83 FTIM2_NOR_TWP(0x1)) 84 #define CONFIG_SYS_NOR_FTIM3 0x04000000 85 #define CONFIG_SYS_IFC_CCR 0x01000000 86 87 #ifndef SYS_NO_FLASH 88 #define CONFIG_FLASH_CFI_DRIVER 89 #define CONFIG_SYS_FLASH_CFI 90 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 91 #define CONFIG_SYS_FLASH_QUIET_TEST 92 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 93 94 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 95 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 96 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 97 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 98 99 #define CONFIG_SYS_FLASH_EMPTY_INFO 100 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 101 #endif 102 #endif 103 104 #ifndef SPL_NO_IFC 105 #define CONFIG_NAND_FSL_IFC 106 #endif 107 108 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 109 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 110 111 #define CONFIG_SYS_NAND_CSPR_EXT (0x0) 112 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 113 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 114 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 115 | CSPR_V) 116 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 117 118 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 119 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 120 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 121 | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ 122 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 123 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ 124 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 125 126 #define CONFIG_SYS_NAND_ONFI_DETECTION 127 128 /* ONFI NAND Flash mode0 Timing Params */ 129 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 130 FTIM0_NAND_TWP(0x18) | \ 131 FTIM0_NAND_TWCHT(0x07) | \ 132 FTIM0_NAND_TWH(0x0a)) 133 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 134 FTIM1_NAND_TWBE(0x39) | \ 135 FTIM1_NAND_TRR(0x0e) | \ 136 FTIM1_NAND_TRP(0x18)) 137 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 138 FTIM2_NAND_TREH(0x0a) | \ 139 FTIM2_NAND_TWHRE(0x1e)) 140 #define CONFIG_SYS_NAND_FTIM3 0x0 141 142 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 143 #define CONFIG_SYS_MAX_NAND_DEVICE 1 144 #define CONFIG_MTD_NAND_VERIFY_WRITE 145 #define CONFIG_CMD_NAND 146 147 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 148 149 #ifndef SPL_NO_QIXIS 150 #define CONFIG_FSL_QIXIS 151 #endif 152 153 #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 154 #define QIXIS_BRDCFG4_OFFSET 0x54 155 #define QIXIS_LBMAP_SWITCH 2 156 #define QIXIS_QMAP_MASK 0xe0 157 #define QIXIS_QMAP_SHIFT 5 158 #define QIXIS_LBMAP_MASK 0x1f 159 #define QIXIS_LBMAP_SHIFT 5 160 #define QIXIS_LBMAP_DFLTBANK 0x00 161 #define QIXIS_LBMAP_ALTBANK 0x20 162 #define QIXIS_LBMAP_SD 0x00 163 #define QIXIS_LBMAP_EMMC 0x00 164 #define QIXIS_LBMAP_SD_QSPI 0x00 165 #define QIXIS_LBMAP_QSPI 0x00 166 #define QIXIS_RCW_SRC_SD 0x40 167 #define QIXIS_RCW_SRC_EMMC 0x41 168 #define QIXIS_RCW_SRC_QSPI 0x62 169 #define QIXIS_RST_CTL_RESET 0x31 170 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 171 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 172 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 173 #define QIXIS_RST_FORCE_MEM 0x01 174 175 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 176 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ 177 | CSPR_PORT_SIZE_8 \ 178 | CSPR_MSEL_GPCM \ 179 | CSPR_V) 180 #define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 181 | CSPR_PORT_SIZE_8 \ 182 | CSPR_MSEL_GPCM \ 183 | CSPR_V) 184 185 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64*1024) 186 #define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0) 187 /* QIXIS Timing parameters*/ 188 #define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 189 FTIM0_GPCM_TEADC(0x0e) | \ 190 FTIM0_GPCM_TEAHC(0x0e)) 191 #define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 192 FTIM1_GPCM_TRAD(0x3f)) 193 #define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 194 FTIM2_GPCM_TCH(0xf) | \ 195 FTIM2_GPCM_TWP(0x3E)) 196 #define SYS_FPGA_CS_FTIM3 0x0 197 198 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 199 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 200 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 201 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 202 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 203 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 204 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 205 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 206 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 207 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT 208 #define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR 209 #define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL 210 #define CONFIG_SYS_AMASK2 CONFIG_SYS_FPGA_AMASK 211 #define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR 212 #define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0 213 #define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1 214 #define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2 215 #define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3 216 #else 217 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 218 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY 219 #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR 220 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 221 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 222 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 223 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 224 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 225 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 226 #endif 227 228 229 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 230 231 #define I2C_MUX_CH_VOL_MONITOR 0xA 232 /* Voltage monitor on channel 2*/ 233 #define I2C_VOL_MONITOR_ADDR 0x63 234 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 235 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 236 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 237 #define I2C_SVDD_MONITOR_ADDR 0x4F 238 239 #define CONFIG_VID_FLS_ENV "ls1088ardb_vdd_mv" 240 #define CONFIG_VID 241 242 /* The lowest and highest voltage allowed for LS1088ARDB */ 243 #define VDD_MV_MIN 819 244 #define VDD_MV_MAX 1212 245 246 #define CONFIG_VOL_MONITOR_LTC3882_SET 247 #define CONFIG_VOL_MONITOR_LTC3882_READ 248 249 /* PM Bus commands code for LTC3882*/ 250 #define PMBUS_CMD_PAGE 0x0 251 #define PMBUS_CMD_READ_VOUT 0x8B 252 #define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 253 #define PMBUS_CMD_VOUT_COMMAND 0x21 254 255 #define PWM_CHANNEL0 0x0 256 257 /* 258 * I2C bus multiplexer 259 */ 260 #define I2C_MUX_PCA_ADDR_PRI 0x77 261 #define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ 262 #define I2C_RETIMER_ADDR 0x18 263 #define I2C_MUX_CH_DEFAULT 0x8 264 #define I2C_MUX_CH5 0xD 265 266 #ifndef SPL_NO_RTC 267 /* 268 * RTC configuration 269 */ 270 #define RTC 271 #define CONFIG_RTC_PCF8563 1 272 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ 273 #define CONFIG_CMD_DATE 274 #endif 275 276 /* EEPROM */ 277 #define CONFIG_ID_EEPROM 278 #define CONFIG_SYS_I2C_EEPROM_NXID 279 #define CONFIG_SYS_EEPROM_BUS_NUM 0 280 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 281 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 282 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 283 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 284 285 #ifndef SPL_NO_QSPI 286 /* QSPI device */ 287 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 288 #define CONFIG_FSL_QSPI 289 #define FSL_QSPI_FLASH_SIZE (1 << 26) 290 #define FSL_QSPI_FLASH_NUM 2 291 #endif 292 #endif 293 294 #define CONFIG_CMD_MEMINFO 295 #define CONFIG_CMD_MEMTEST 296 #define CONFIG_SYS_MEMTEST_START 0x80000000 297 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 298 299 #ifdef CONFIG_SPL_BUILD 300 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 301 #else 302 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 303 #endif 304 305 #define CONFIG_FSL_MEMAC 306 307 #ifndef SPL_NO_ENV 308 /* Initial environment variables */ 309 #if defined(CONFIG_QSPI_BOOT) 310 #define MC_INIT_CMD \ 311 "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \ 312 "sf read 0x80100000 0xE00000 0x100000;" \ 313 "env exists secureboot && " \ 314 "sf read 0x80700000 0x700000 0x40000 && " \ 315 "sf read 0x80740000 0x740000 0x40000 && " \ 316 "esbc_validate 0x80700000 && " \ 317 "esbc_validate 0x80740000 ;" \ 318 "fsl_mc start mc 0x80000000 0x80100000\0" \ 319 "mcmemsize=0x70000000\0" 320 #elif defined(CONFIG_SD_BOOT) 321 #define MC_INIT_CMD \ 322 "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \ 323 "mmc read 0x80100000 0x7000 0x800;" \ 324 "env exists secureboot && " \ 325 "mmc read 0x80700000 0x3800 0x10 && " \ 326 "mmc read 0x80740000 0x3A00 0x10 && " \ 327 "esbc_validate 0x80700000 && " \ 328 "esbc_validate 0x80740000 ;" \ 329 "fsl_mc start mc 0x80000000 0x80100000\0" \ 330 "mcmemsize=0x70000000\0" 331 #endif 332 333 #undef CONFIG_EXTRA_ENV_SETTINGS 334 #define CONFIG_EXTRA_ENV_SETTINGS \ 335 "BOARD=ls1088ardb\0" \ 336 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 337 "ramdisk_addr=0x800000\0" \ 338 "ramdisk_size=0x2000000\0" \ 339 "fdt_high=0xa0000000\0" \ 340 "initrd_high=0xffffffffffffffff\0" \ 341 "fdt_addr=0x64f00000\0" \ 342 "kernel_addr=0x1000000\0" \ 343 "kernel_addr_sd=0x8000\0" \ 344 "kernelhdr_addr_sd=0x4000\0" \ 345 "kernel_start=0x580100000\0" \ 346 "kernelheader_start=0x580800000\0" \ 347 "scriptaddr=0x80000000\0" \ 348 "scripthdraddr=0x80080000\0" \ 349 "fdtheader_addr_r=0x80100000\0" \ 350 "kernelheader_addr=0x800000\0" \ 351 "kernelheader_addr_r=0x80200000\0" \ 352 "kernel_addr_r=0x81000000\0" \ 353 "kernelheader_size=0x40000\0" \ 354 "fdt_addr_r=0x90000000\0" \ 355 "load_addr=0xa0000000\0" \ 356 "kernel_size=0x2800000\0" \ 357 "kernel_size_sd=0x14000\0" \ 358 "kernelhdr_size_sd=0x10\0" \ 359 MC_INIT_CMD \ 360 BOOTENV \ 361 "boot_scripts=ls1088ardb_boot.scr\0" \ 362 "boot_script_hdr=hdr_ls1088ardb_bs.out\0" \ 363 "scan_dev_for_boot_part=" \ 364 "part list ${devtype} ${devnum} devplist; " \ 365 "env exists devplist || setenv devplist 1; " \ 366 "for distro_bootpart in ${devplist}; do " \ 367 "if fstype ${devtype} " \ 368 "${devnum}:${distro_bootpart} " \ 369 "bootfstype; then " \ 370 "run scan_dev_for_boot; " \ 371 "fi; " \ 372 "done\0" \ 373 "scan_dev_for_boot=" \ 374 "echo Scanning ${devtype} " \ 375 "${devnum}:${distro_bootpart}...; " \ 376 "for prefix in ${boot_prefixes}; do " \ 377 "run scan_dev_for_scripts; " \ 378 "done;\0" \ 379 "boot_a_script=" \ 380 "load ${devtype} ${devnum}:${distro_bootpart} " \ 381 "${scriptaddr} ${prefix}${script}; " \ 382 "env exists secureboot && load ${devtype} " \ 383 "${devnum}:${distro_bootpart} " \ 384 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 385 "&& esbc_validate ${scripthdraddr};" \ 386 "source ${scriptaddr}\0" \ 387 "installer=load mmc 0:2 $load_addr " \ 388 "/flex_installer_arm64.itb; " \ 389 "env exists mcinitcmd && run mcinitcmd && " \ 390 "mmc read 0x80200000 0x6800 0x800;" \ 391 "fsl_mc apply dpl 0x80200000;" \ 392 "bootm $load_addr#ls1088ardb\0" \ 393 "qspi_bootcmd=echo Trying load from qspi..;" \ 394 "sf probe && sf read $load_addr " \ 395 "$kernel_addr $kernel_size ; env exists secureboot " \ 396 "&& sf read $kernelheader_addr_r $kernelheader_addr " \ 397 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ 398 "bootm $load_addr#$BOARD\0" \ 399 "sd_bootcmd=echo Trying load from sd card..;" \ 400 "mmcinfo; mmc read $load_addr " \ 401 "$kernel_addr_sd $kernel_size_sd ;" \ 402 "env exists secureboot && mmc read $kernelheader_addr_r "\ 403 "$kernelhdr_addr_sd $kernelhdr_size_sd " \ 404 " && esbc_validate ${kernelheader_addr_r};" \ 405 "bootm $load_addr#$BOARD\0" 406 407 #undef CONFIG_BOOTCOMMAND 408 #if defined(CONFIG_QSPI_BOOT) 409 /* Try to boot an on-QSPI kernel first, then do normal distro boot */ 410 #define CONFIG_BOOTCOMMAND \ 411 "sf read 0x80200000 0xd00000 0x100000;" \ 412 "env exists mcinitcmd && env exists secureboot " \ 413 " && sf read 0x80780000 0x780000 0x100000 " \ 414 "&& esbc_validate 0x80780000;env exists mcinitcmd " \ 415 "&& fsl_mc apply dpl 0x80200000;" \ 416 "run distro_bootcmd;run qspi_bootcmd;" \ 417 "env exists secureboot && esbc_halt;" 418 419 /* Try to boot an on-SD kernel first, then do normal distro boot */ 420 #elif defined(CONFIG_SD_BOOT) 421 #define CONFIG_BOOTCOMMAND \ 422 "env exists mcinitcmd && mmcinfo; " \ 423 "mmc read 0x80200000 0x6800 0x800; " \ 424 "env exists mcinitcmd && env exists secureboot " \ 425 " && mmc read 0x80780000 0x3800 0x10 " \ 426 "&& esbc_validate 0x80780000;env exists mcinitcmd " \ 427 "&& fsl_mc apply dpl 0x80200000;" \ 428 "run distro_bootcmd;run sd_bootcmd;" \ 429 "env exists secureboot && esbc_halt;" 430 #endif 431 432 /* MAC/PHY configuration */ 433 #ifdef CONFIG_FSL_MC_ENET 434 #define CONFIG_PHYLIB_10G 435 #define CONFIG_PHY_GIGE 436 #define CONFIG_PHYLIB 437 438 #define CONFIG_PHY_VITESSE 439 #define CONFIG_PHY_AQUANTIA 440 #define AQ_PHY_ADDR1 0x00 441 #define AQR105_IRQ_MASK 0x00000004 442 443 #define QSGMII1_PORT1_PHY_ADDR 0x0c 444 #define QSGMII1_PORT2_PHY_ADDR 0x0d 445 #define QSGMII1_PORT3_PHY_ADDR 0x0e 446 #define QSGMII1_PORT4_PHY_ADDR 0x0f 447 #define QSGMII2_PORT1_PHY_ADDR 0x1c 448 #define QSGMII2_PORT2_PHY_ADDR 0x1d 449 #define QSGMII2_PORT3_PHY_ADDR 0x1e 450 #define QSGMII2_PORT4_PHY_ADDR 0x1f 451 452 #define CONFIG_MII 453 #define CONFIG_ETHPRIME "DPMAC1@xgmii" 454 #define CONFIG_PHY_GIGE 455 #endif 456 #endif 457 458 /* MMC */ 459 #ifdef CONFIG_MMC 460 #define CONFIG_FSL_ESDHC 461 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 462 #endif 463 464 #ifndef SPL_NO_ENV 465 #undef CONFIG_CMDLINE_EDITING 466 #include <config_distro_defaults.h> 467 468 #define BOOT_TARGET_DEVICES(func) \ 469 func(MMC, mmc, 0) \ 470 func(SCSI, scsi, 0) \ 471 func(DHCP, dhcp, na) 472 #include <config_distro_bootcmd.h> 473 #endif 474 475 #include <asm/fsl_secure_boot.h> 476 477 #endif /* __LS1088A_RDB_H */ 478