xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 8ee59472)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2016 Freescale Semiconductor, Inc.
4  */
5 
6 #ifndef __LS1046AQDS_H__
7 #define __LS1046AQDS_H__
8 
9 #include "ls1046a_common.h"
10 
11 #ifndef __ASSEMBLY__
12 unsigned long get_board_sys_clk(void);
13 unsigned long get_board_ddr_clk(void);
14 #endif
15 
16 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
17 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
18 
19 #define CONFIG_SKIP_LOWLEVEL_INIT
20 
21 #define CONFIG_LAYERSCAPE_NS_ACCESS
22 
23 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
24 /* Physical Memory Map */
25 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
26 #define CONFIG_NR_DRAM_BANKS		2
27 
28 #define CONFIG_DDR_SPD
29 #define SPD_EEPROM_ADDRESS		0x51
30 #define CONFIG_SYS_SPD_BUS_NUM		0
31 
32 #ifndef CONFIG_SPL
33 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
34 #endif
35 
36 #define CONFIG_DDR_ECC
37 #ifdef CONFIG_DDR_ECC
38 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
39 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
40 #endif
41 
42 /* DSPI */
43 #ifdef CONFIG_FSL_DSPI
44 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
45 #define CONFIG_SPI_FLASH_SST		/* cs1 */
46 #define CONFIG_SPI_FLASH_EON		/* cs2 */
47 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
48 #define CONFIG_SF_DEFAULT_BUS		1
49 #define CONFIG_SF_DEFAULT_CS		0
50 #endif
51 #endif
52 
53 /* QSPI */
54 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
55 #ifdef CONFIG_FSL_QSPI
56 #define CONFIG_SPI_FLASH_SPANSION
57 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
58 #define FSL_QSPI_FLASH_NUM		2
59 #endif
60 #endif
61 
62 #ifdef CONFIG_SYS_DPAA_FMAN
63 #define CONFIG_FMAN_ENET
64 #define CONFIG_PHY_VITESSE
65 #define CONFIG_PHY_REALTEK
66 #define CONFIG_PHYLIB_10G
67 #define RGMII_PHY1_ADDR		0x1
68 #define RGMII_PHY2_ADDR		0x2
69 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
70 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
71 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
72 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
73 /* PHY address on QSGMII riser card on slot 2 */
74 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
75 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
76 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
77 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
78 #endif
79 
80 #ifdef CONFIG_RAMBOOT_PBL
81 #define CONFIG_SYS_FSL_PBL_PBI \
82 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
83 #endif
84 
85 #ifdef CONFIG_NAND_BOOT
86 #define CONFIG_SYS_FSL_PBL_RCW \
87 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
88 #endif
89 
90 #ifdef CONFIG_SD_BOOT
91 #ifdef CONFIG_SD_BOOT_QSPI
92 #define CONFIG_SYS_FSL_PBL_RCW \
93 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
94 #else
95 #define CONFIG_SYS_FSL_PBL_RCW \
96 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
97 #endif
98 #endif
99 
100 /* IFC */
101 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
102 #define	CONFIG_FSL_IFC
103 /*
104  * CONFIG_SYS_FLASH_BASE has the final address (core view)
105  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
106  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
107  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
108  */
109 #define CONFIG_SYS_FLASH_BASE			0x60000000
110 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
111 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
112 
113 #ifdef CONFIG_MTD_NOR_FLASH
114 #define CONFIG_FLASH_CFI_DRIVER
115 #define CONFIG_SYS_FLASH_CFI
116 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
117 #define CONFIG_SYS_FLASH_QUIET_TEST
118 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
119 #endif
120 #endif
121 
122 /* LPUART */
123 #ifdef CONFIG_LPUART
124 #define CONFIG_LPUART_32B_REG
125 #define CFG_UART_MUX_MASK	0x6
126 #define CFG_UART_MUX_SHIFT	1
127 #define CFG_LPUART_EN		0x2
128 #endif
129 
130 /* EEPROM */
131 #define CONFIG_ID_EEPROM
132 #define CONFIG_SYS_I2C_EEPROM_NXID
133 #define CONFIG_SYS_EEPROM_BUS_NUM		0
134 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
135 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
136 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
137 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
138 
139 /*
140  * IFC Definitions
141  */
142 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
143 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
144 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
145 				CSPR_PORT_SIZE_16 | \
146 				CSPR_MSEL_NOR | \
147 				CSPR_V)
148 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
149 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
150 				+ 0x8000000) | \
151 				CSPR_PORT_SIZE_16 | \
152 				CSPR_MSEL_NOR | \
153 				CSPR_V)
154 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
155 
156 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
157 					CSOR_NOR_TRHZ_80)
158 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
159 					FTIM0_NOR_TEADC(0x5) | \
160 					FTIM0_NOR_TAVDS(0x6) | \
161 					FTIM0_NOR_TEAHC(0x5))
162 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
163 					FTIM1_NOR_TRAD_NOR(0x1a) | \
164 					FTIM1_NOR_TSEQRAD_NOR(0x13))
165 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x8) | \
166 					FTIM2_NOR_TCH(0x8) | \
167 					FTIM2_NOR_TWPH(0xe) | \
168 					FTIM2_NOR_TWP(0x1c))
169 #define CONFIG_SYS_NOR_FTIM3		0
170 
171 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
172 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
173 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
174 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
175 
176 #define CONFIG_SYS_FLASH_EMPTY_INFO
177 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
178 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
179 
180 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
181 #define CONFIG_SYS_WRITE_SWAPPED_DATA
182 
183 /*
184  * NAND Flash Definitions
185  */
186 #define CONFIG_NAND_FSL_IFC
187 
188 #define CONFIG_SYS_NAND_BASE		0x7e800000
189 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
190 
191 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
192 
193 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
194 				| CSPR_PORT_SIZE_8	\
195 				| CSPR_MSEL_NAND	\
196 				| CSPR_V)
197 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
198 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
199 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
200 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
201 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
202 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
203 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
204 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
205 
206 #define CONFIG_SYS_NAND_ONFI_DETECTION
207 
208 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
209 					FTIM0_NAND_TWP(0x18)   | \
210 					FTIM0_NAND_TWCHT(0x7) | \
211 					FTIM0_NAND_TWH(0xa))
212 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
213 					FTIM1_NAND_TWBE(0x39)  | \
214 					FTIM1_NAND_TRR(0xe)   | \
215 					FTIM1_NAND_TRP(0x18))
216 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
217 					FTIM2_NAND_TREH(0xa) | \
218 					FTIM2_NAND_TWHRE(0x1e))
219 #define CONFIG_SYS_NAND_FTIM3           0x0
220 
221 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
222 #define CONFIG_SYS_MAX_NAND_DEVICE	1
223 #define CONFIG_MTD_NAND_VERIFY_WRITE
224 
225 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
226 #endif
227 
228 #ifdef CONFIG_NAND_BOOT
229 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
230 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
231 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
232 #endif
233 
234 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
235 #define CONFIG_QIXIS_I2C_ACCESS
236 #define CONFIG_SYS_I2C_EARLY_INIT
237 #endif
238 
239 /*
240  * QIXIS Definitions
241  */
242 #define CONFIG_FSL_QIXIS
243 
244 #ifdef CONFIG_FSL_QIXIS
245 #define QIXIS_BASE			0x7fb00000
246 #define QIXIS_BASE_PHYS			QIXIS_BASE
247 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
248 #define QIXIS_LBMAP_SWITCH		6
249 #define QIXIS_LBMAP_MASK		0x0f
250 #define QIXIS_LBMAP_SHIFT		0
251 #define QIXIS_LBMAP_DFLTBANK		0x00
252 #define QIXIS_LBMAP_ALTBANK		0x04
253 #define QIXIS_LBMAP_NAND		0x09
254 #define QIXIS_LBMAP_SD			0x00
255 #define QIXIS_LBMAP_SD_QSPI		0xff
256 #define QIXIS_LBMAP_QSPI		0xff
257 #define QIXIS_RCW_SRC_NAND		0x110
258 #define QIXIS_RCW_SRC_SD		0x040
259 #define QIXIS_RCW_SRC_QSPI		0x045
260 #define QIXIS_RST_CTL_RESET		0x41
261 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
262 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
263 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
264 
265 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
266 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
267 					CSPR_PORT_SIZE_8 | \
268 					CSPR_MSEL_GPCM | \
269 					CSPR_V)
270 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
271 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
272 					CSOR_NOR_NOR_MODE_AVD_NOR | \
273 					CSOR_NOR_TRHZ_80)
274 
275 /*
276  * QIXIS Timing parameters for IFC GPCM
277  */
278 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
279 					FTIM0_GPCM_TEADC(0x20) | \
280 					FTIM0_GPCM_TEAHC(0x10))
281 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
282 					FTIM1_GPCM_TRAD(0x1f))
283 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
284 					FTIM2_GPCM_TCH(0x8) | \
285 					FTIM2_GPCM_TWP(0xf0))
286 #define CONFIG_SYS_FPGA_FTIM3		0x0
287 #endif
288 
289 #ifdef CONFIG_NAND_BOOT
290 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
291 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
292 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
293 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
294 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
295 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
296 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
297 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
298 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
299 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
300 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
301 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
302 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
303 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
304 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
305 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
306 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
307 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
308 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
309 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
310 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
311 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
312 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
313 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
314 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
315 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
316 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
317 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
318 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
319 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
320 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
321 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
322 #else
323 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
324 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
325 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
326 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
327 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
328 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
329 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
330 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
331 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
332 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
333 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
334 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
335 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
336 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
337 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
338 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
339 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
340 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
341 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
342 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
343 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
344 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
345 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
346 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
347 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
348 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
349 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
350 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
351 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
352 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
353 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
354 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
355 #endif
356 
357 /*
358  * I2C bus multiplexer
359  */
360 #define I2C_MUX_PCA_ADDR_PRI		0x77
361 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
362 #define I2C_RETIMER_ADDR		0x18
363 #define I2C_MUX_CH_DEFAULT		0x8
364 #define I2C_MUX_CH_CH7301		0xC
365 #define I2C_MUX_CH5			0xD
366 #define I2C_MUX_CH6			0xE
367 #define I2C_MUX_CH7			0xF
368 
369 #define I2C_MUX_CH_VOL_MONITOR 0xa
370 
371 /* Voltage monitor on channel 2*/
372 #define I2C_VOL_MONITOR_ADDR           0x40
373 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
374 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
375 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
376 
377 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
378 #ifndef CONFIG_SPL_BUILD
379 #define CONFIG_VID
380 #endif
381 #define CONFIG_VOL_MONITOR_IR36021_SET
382 #define CONFIG_VOL_MONITOR_INA220
383 /* The lowest and highest voltage allowed for LS1046AQDS */
384 #define VDD_MV_MIN			819
385 #define VDD_MV_MAX			1212
386 
387 /*
388  * Miscellaneous configurable options
389  */
390 #define CONFIG_MISC_INIT_R
391 
392 #define CONFIG_SYS_MEMTEST_START	0x80000000
393 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
394 
395 #define CONFIG_SYS_HZ			1000
396 
397 #define CONFIG_SYS_INIT_SP_OFFSET \
398 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
399 
400 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
401 
402 /*
403  * Environment
404  */
405 #define CONFIG_ENV_OVERWRITE
406 
407 #ifdef CONFIG_NAND_BOOT
408 #define CONFIG_ENV_SIZE			0x2000
409 #define CONFIG_ENV_OFFSET		(12 * CONFIG_SYS_NAND_BLOCK_SIZE)
410 #elif defined(CONFIG_SD_BOOT)
411 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
412 #define CONFIG_SYS_MMC_ENV_DEV		0
413 #define CONFIG_ENV_SIZE			0x2000
414 #elif defined(CONFIG_QSPI_BOOT)
415 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
416 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
417 #define CONFIG_ENV_SECT_SIZE		0x10000
418 #else
419 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
420 #define CONFIG_ENV_SECT_SIZE		0x20000
421 #define CONFIG_ENV_SIZE			0x20000
422 #endif
423 
424 #define CONFIG_CMDLINE_TAG
425 
426 #undef CONFIG_BOOTCOMMAND
427 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
428 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
429 					"e0000 f00000 && bootm $kernel_load"
430 #else
431 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
432 					"$kernel_size && bootm $kernel_load"
433 #endif
434 
435 #include <asm/fsl_secure_boot.h>
436 
437 #endif /* __LS1046AQDS_H__ */
438