xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 679590eb)
1 /*
2  * Copyright 2016 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046AQDS_H__
8 #define __LS1046AQDS_H__
9 
10 #include "ls1046a_common.h"
11 
12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
13 #define CONFIG_SYS_TEXT_BASE		0x82000000
14 #elif defined(CONFIG_QSPI_BOOT)
15 #define CONFIG_SYS_TEXT_BASE		0x40100000
16 #else
17 #define CONFIG_SYS_TEXT_BASE		0x60100000
18 #endif
19 
20 #ifndef __ASSEMBLY__
21 unsigned long get_board_sys_clk(void);
22 unsigned long get_board_ddr_clk(void);
23 #endif
24 
25 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
26 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
27 
28 #define CONFIG_SKIP_LOWLEVEL_INIT
29 
30 #define CONFIG_LAYERSCAPE_NS_ACCESS
31 
32 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
33 /* Physical Memory Map */
34 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
35 #define CONFIG_NR_DRAM_BANKS		2
36 
37 #define CONFIG_DDR_SPD
38 #define SPD_EEPROM_ADDRESS		0x51
39 #define CONFIG_SYS_SPD_BUS_NUM		0
40 
41 #ifndef CONFIG_SPL
42 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
43 #endif
44 
45 #define CONFIG_DDR_ECC
46 #ifdef CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
49 #endif
50 
51 /* DSPI */
52 #ifdef CONFIG_FSL_DSPI
53 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
54 #define CONFIG_SPI_FLASH_SST		/* cs1 */
55 #define CONFIG_SPI_FLASH_EON		/* cs2 */
56 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
57 #define CONFIG_SF_DEFAULT_BUS		1
58 #define CONFIG_SF_DEFAULT_CS		0
59 #endif
60 #endif
61 
62 /* QSPI */
63 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
64 #ifdef CONFIG_FSL_QSPI
65 #define CONFIG_SPI_FLASH_SPANSION
66 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
67 #define FSL_QSPI_FLASH_NUM		2
68 #endif
69 #endif
70 
71 #ifdef CONFIG_SYS_DPAA_FMAN
72 #define CONFIG_FMAN_ENET
73 #define CONFIG_PHYLIB
74 #define CONFIG_PHY_VITESSE
75 #define CONFIG_PHY_REALTEK
76 #define CONFIG_PHYLIB_10G
77 #define RGMII_PHY1_ADDR		0x1
78 #define RGMII_PHY2_ADDR		0x2
79 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
80 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
81 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
82 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
83 /* PHY address on QSGMII riser card on slot 2 */
84 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
85 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
86 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
87 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
88 #endif
89 
90 #ifdef CONFIG_RAMBOOT_PBL
91 #define CONFIG_SYS_FSL_PBL_PBI \
92 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
93 #endif
94 
95 #ifdef CONFIG_NAND_BOOT
96 #define CONFIG_SYS_FSL_PBL_RCW \
97 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
98 #endif
99 
100 #ifdef CONFIG_SD_BOOT
101 #ifdef CONFIG_SD_BOOT_QSPI
102 #define CONFIG_SYS_FSL_PBL_RCW \
103 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
104 #else
105 #define CONFIG_SYS_FSL_PBL_RCW \
106 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
107 #endif
108 #endif
109 
110 /* IFC */
111 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
112 #define	CONFIG_FSL_IFC
113 /*
114  * CONFIG_SYS_FLASH_BASE has the final address (core view)
115  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
116  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
117  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
118  */
119 #define CONFIG_SYS_FLASH_BASE			0x60000000
120 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
121 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
122 
123 #ifdef CONFIG_MTD_NOR_FLASH
124 #define CONFIG_FLASH_CFI_DRIVER
125 #define CONFIG_SYS_FLASH_CFI
126 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
127 #define CONFIG_SYS_FLASH_QUIET_TEST
128 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
129 #endif
130 #endif
131 
132 /* LPUART */
133 #ifdef CONFIG_LPUART
134 #define CONFIG_LPUART_32B_REG
135 #define CFG_UART_MUX_MASK	0x6
136 #define CFG_UART_MUX_SHIFT	1
137 #define CFG_LPUART_EN		0x2
138 #endif
139 
140 /* USB */
141 #define CONFIG_HAS_FSL_XHCI_USB
142 #ifdef CONFIG_HAS_FSL_XHCI_USB
143 #define CONFIG_USB_XHCI_HCD
144 #define CONFIG_USB_XHCI_FSL
145 #define CONFIG_USB_XHCI_DWC3
146 #define CONFIG_USB_MAX_CONTROLLER_COUNT         3
147 #define CONFIG_USB_STORAGE
148 #endif
149 
150 /* SATA */
151 #define CONFIG_LIBATA
152 #define CONFIG_SCSI_AHCI
153 #define CONFIG_SCSI_AHCI_PLAT
154 
155 /* EEPROM */
156 #define CONFIG_ID_EEPROM
157 #define CONFIG_SYS_I2C_EEPROM_NXID
158 #define CONFIG_SYS_EEPROM_BUS_NUM		0
159 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
160 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
161 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
162 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
163 
164 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
165 
166 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
167 #define CONFIG_SYS_SCSI_MAX_LUN			1
168 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
169 						CONFIG_SYS_SCSI_MAX_LUN)
170 
171 /*
172  * IFC Definitions
173  */
174 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
175 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
176 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
177 				CSPR_PORT_SIZE_16 | \
178 				CSPR_MSEL_NOR | \
179 				CSPR_V)
180 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
181 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
182 				+ 0x8000000) | \
183 				CSPR_PORT_SIZE_16 | \
184 				CSPR_MSEL_NOR | \
185 				CSPR_V)
186 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
187 
188 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
189 					CSOR_NOR_TRHZ_80)
190 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
191 					FTIM0_NOR_TEADC(0x5) | \
192 					FTIM0_NOR_TEAHC(0x5))
193 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
194 					FTIM1_NOR_TRAD_NOR(0x1a) | \
195 					FTIM1_NOR_TSEQRAD_NOR(0x13))
196 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
197 					FTIM2_NOR_TCH(0x4) | \
198 					FTIM2_NOR_TWPH(0xe) | \
199 					FTIM2_NOR_TWP(0x1c))
200 #define CONFIG_SYS_NOR_FTIM3		0
201 
202 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
203 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
204 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
205 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
206 
207 #define CONFIG_SYS_FLASH_EMPTY_INFO
208 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
209 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
210 
211 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
212 #define CONFIG_SYS_WRITE_SWAPPED_DATA
213 
214 /*
215  * NAND Flash Definitions
216  */
217 #define CONFIG_NAND_FSL_IFC
218 
219 #define CONFIG_SYS_NAND_BASE		0x7e800000
220 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
221 
222 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
223 
224 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
225 				| CSPR_PORT_SIZE_8	\
226 				| CSPR_MSEL_NAND	\
227 				| CSPR_V)
228 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
229 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
230 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
231 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
232 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
233 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
234 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
235 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
236 
237 #define CONFIG_SYS_NAND_ONFI_DETECTION
238 
239 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
240 					FTIM0_NAND_TWP(0x18)   | \
241 					FTIM0_NAND_TWCHT(0x7) | \
242 					FTIM0_NAND_TWH(0xa))
243 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
244 					FTIM1_NAND_TWBE(0x39)  | \
245 					FTIM1_NAND_TRR(0xe)   | \
246 					FTIM1_NAND_TRP(0x18))
247 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
248 					FTIM2_NAND_TREH(0xa) | \
249 					FTIM2_NAND_TWHRE(0x1e))
250 #define CONFIG_SYS_NAND_FTIM3           0x0
251 
252 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
253 #define CONFIG_SYS_MAX_NAND_DEVICE	1
254 #define CONFIG_MTD_NAND_VERIFY_WRITE
255 
256 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
257 #endif
258 
259 #ifdef CONFIG_NAND_BOOT
260 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
261 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
262 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
263 #endif
264 
265 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
266 #define CONFIG_QIXIS_I2C_ACCESS
267 #define CONFIG_SYS_I2C_EARLY_INIT
268 #endif
269 
270 /*
271  * QIXIS Definitions
272  */
273 #define CONFIG_FSL_QIXIS
274 
275 #ifdef CONFIG_FSL_QIXIS
276 #define QIXIS_BASE			0x7fb00000
277 #define QIXIS_BASE_PHYS			QIXIS_BASE
278 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
279 #define QIXIS_LBMAP_SWITCH		6
280 #define QIXIS_LBMAP_MASK		0x0f
281 #define QIXIS_LBMAP_SHIFT		0
282 #define QIXIS_LBMAP_DFLTBANK		0x00
283 #define QIXIS_LBMAP_ALTBANK		0x04
284 #define QIXIS_LBMAP_NAND		0x09
285 #define QIXIS_LBMAP_SD			0x00
286 #define QIXIS_LBMAP_SD_QSPI		0xff
287 #define QIXIS_LBMAP_QSPI		0xff
288 #define QIXIS_RCW_SRC_NAND		0x110
289 #define QIXIS_RCW_SRC_SD		0x040
290 #define QIXIS_RCW_SRC_QSPI		0x045
291 #define QIXIS_RST_CTL_RESET		0x41
292 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
293 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
294 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
295 
296 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
297 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
298 					CSPR_PORT_SIZE_8 | \
299 					CSPR_MSEL_GPCM | \
300 					CSPR_V)
301 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
302 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
303 					CSOR_NOR_NOR_MODE_AVD_NOR | \
304 					CSOR_NOR_TRHZ_80)
305 
306 /*
307  * QIXIS Timing parameters for IFC GPCM
308  */
309 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
310 					FTIM0_GPCM_TEADC(0x20) | \
311 					FTIM0_GPCM_TEAHC(0x10))
312 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
313 					FTIM1_GPCM_TRAD(0x1f))
314 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
315 					FTIM2_GPCM_TCH(0x8) | \
316 					FTIM2_GPCM_TWP(0xf0))
317 #define CONFIG_SYS_FPGA_FTIM3		0x0
318 #endif
319 
320 #ifdef CONFIG_NAND_BOOT
321 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
322 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
323 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
324 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
325 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
326 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
327 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
328 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
329 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
330 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
331 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
332 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
333 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
334 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
335 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
336 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
337 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
338 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
339 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
340 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
341 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
342 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
343 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
344 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
345 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
346 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
347 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
348 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
349 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
350 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
351 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
352 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
353 #else
354 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
355 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
356 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
357 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
358 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
359 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
360 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
361 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
362 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
363 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
364 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
365 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
366 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
367 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
368 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
369 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
370 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
371 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
372 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
373 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
374 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
375 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
376 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
377 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
378 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
379 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
380 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
381 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
382 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
383 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
384 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
385 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
386 #endif
387 
388 /*
389  * I2C bus multiplexer
390  */
391 #define I2C_MUX_PCA_ADDR_PRI		0x77
392 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
393 #define I2C_RETIMER_ADDR		0x18
394 #define I2C_MUX_CH_DEFAULT		0x8
395 #define I2C_MUX_CH_CH7301		0xC
396 #define I2C_MUX_CH5			0xD
397 #define I2C_MUX_CH6			0xE
398 #define I2C_MUX_CH7			0xF
399 
400 #define I2C_MUX_CH_VOL_MONITOR 0xa
401 
402 /* Voltage monitor on channel 2*/
403 #define I2C_VOL_MONITOR_ADDR           0x40
404 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
405 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
406 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
407 
408 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
409 #ifndef CONFIG_SPL_BUILD
410 #define CONFIG_VID
411 #endif
412 #define CONFIG_VOL_MONITOR_IR36021_SET
413 #define CONFIG_VOL_MONITOR_INA220
414 /* The lowest and highest voltage allowed for LS1046AQDS */
415 #define VDD_MV_MIN			819
416 #define VDD_MV_MAX			1212
417 
418 /*
419  * Miscellaneous configurable options
420  */
421 #define CONFIG_MISC_INIT_R
422 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
423 #define CONFIG_AUTO_COMPLETE
424 #define CONFIG_SYS_PBSIZE		\
425 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
426 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
427 
428 #define CONFIG_SYS_MEMTEST_START	0x80000000
429 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
430 
431 #define CONFIG_SYS_HZ			1000
432 
433 #define CONFIG_SYS_INIT_SP_OFFSET \
434 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
435 
436 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
437 
438 /*
439  * Environment
440  */
441 #define CONFIG_ENV_OVERWRITE
442 
443 #ifdef CONFIG_NAND_BOOT
444 #define CONFIG_ENV_SIZE			0x2000
445 #define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
446 #elif defined(CONFIG_SD_BOOT)
447 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
448 #define CONFIG_SYS_MMC_ENV_DEV		0
449 #define CONFIG_ENV_SIZE			0x2000
450 #elif defined(CONFIG_QSPI_BOOT)
451 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
452 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
453 #define CONFIG_ENV_SECT_SIZE		0x10000
454 #else
455 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
456 #define CONFIG_ENV_SECT_SIZE		0x20000
457 #define CONFIG_ENV_SIZE			0x20000
458 #endif
459 
460 #define CONFIG_CMDLINE_TAG
461 
462 #undef CONFIG_BOOTCOMMAND
463 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
464 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
465 					"e0000 f00000 && bootm $kernel_load"
466 #else
467 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
468 					"$kernel_size && bootm $kernel_load"
469 #endif
470 
471 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
472 #define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
473 			"14m(free)"
474 #else
475 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \
476 			"2m@0x100000(nor_bank0_uboot),"\
477 			"40m@0x1100000(nor_bank0_fit)," \
478 			"7m(nor_bank0_user)," \
479 			"2m@0x4100000(nor_bank4_uboot)," \
480 			"40m@0x5100000(nor_bank4_fit),"\
481 			"-(nor_bank4_user);" \
482 			"7e800000.flash:" \
483 			"4m(nand_uboot),36m(nand_kernel)," \
484 			"472m(nand_free);spi0.0:2m(uboot)," \
485 			"14m(free)"
486 #endif
487 
488 #include <asm/fsl_secure_boot.h>
489 
490 #endif /* __LS1046AQDS_H__ */
491