xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 4c0411eb)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2016 Freescale Semiconductor, Inc.
4  */
5 
6 #ifndef __LS1046AQDS_H__
7 #define __LS1046AQDS_H__
8 
9 #include "ls1046a_common.h"
10 
11 #ifndef __ASSEMBLY__
12 unsigned long get_board_sys_clk(void);
13 unsigned long get_board_ddr_clk(void);
14 #endif
15 
16 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
17 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
18 
19 #define CONFIG_SKIP_LOWLEVEL_INIT
20 
21 #define CONFIG_LAYERSCAPE_NS_ACCESS
22 
23 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
24 /* Physical Memory Map */
25 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
26 
27 #define CONFIG_DDR_SPD
28 #define SPD_EEPROM_ADDRESS		0x51
29 #define CONFIG_SYS_SPD_BUS_NUM		0
30 
31 #ifndef CONFIG_SPL
32 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
33 #endif
34 
35 #define CONFIG_DDR_ECC
36 #ifdef CONFIG_DDR_ECC
37 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
38 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
39 #endif
40 
41 /* DSPI */
42 #ifdef CONFIG_FSL_DSPI
43 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
44 #define CONFIG_SPI_FLASH_SST		/* cs1 */
45 #define CONFIG_SPI_FLASH_EON		/* cs2 */
46 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
47 #define CONFIG_SF_DEFAULT_BUS		1
48 #define CONFIG_SF_DEFAULT_CS		0
49 #endif
50 #endif
51 
52 /* QSPI */
53 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
54 #ifdef CONFIG_FSL_QSPI
55 #define CONFIG_SPI_FLASH_SPANSION
56 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
57 #define FSL_QSPI_FLASH_NUM		2
58 #endif
59 #endif
60 
61 #ifdef CONFIG_SYS_DPAA_FMAN
62 #define CONFIG_FMAN_ENET
63 #define CONFIG_PHY_VITESSE
64 #define CONFIG_PHY_REALTEK
65 #define CONFIG_PHYLIB_10G
66 #define RGMII_PHY1_ADDR		0x1
67 #define RGMII_PHY2_ADDR		0x2
68 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
69 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
70 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
71 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
72 /* PHY address on QSGMII riser card on slot 2 */
73 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
74 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
75 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
76 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
77 #endif
78 
79 #ifdef CONFIG_RAMBOOT_PBL
80 #define CONFIG_SYS_FSL_PBL_PBI \
81 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
82 #endif
83 
84 #ifdef CONFIG_NAND_BOOT
85 #define CONFIG_SYS_FSL_PBL_RCW \
86 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
87 #endif
88 
89 #ifdef CONFIG_SD_BOOT
90 #ifdef CONFIG_SD_BOOT_QSPI
91 #define CONFIG_SYS_FSL_PBL_RCW \
92 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
93 #else
94 #define CONFIG_SYS_FSL_PBL_RCW \
95 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
96 #endif
97 #endif
98 
99 /* IFC */
100 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
101 #define	CONFIG_FSL_IFC
102 /*
103  * CONFIG_SYS_FLASH_BASE has the final address (core view)
104  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
105  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
106  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
107  */
108 #define CONFIG_SYS_FLASH_BASE			0x60000000
109 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
110 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
111 
112 #ifdef CONFIG_MTD_NOR_FLASH
113 #define CONFIG_SYS_FLASH_QUIET_TEST
114 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
115 #endif
116 #endif
117 
118 /* LPUART */
119 #ifdef CONFIG_LPUART
120 #define CONFIG_LPUART_32B_REG
121 #define CFG_UART_MUX_MASK	0x6
122 #define CFG_UART_MUX_SHIFT	1
123 #define CFG_LPUART_EN		0x2
124 #endif
125 
126 /* EEPROM */
127 #define CONFIG_ID_EEPROM
128 #define CONFIG_SYS_I2C_EEPROM_NXID
129 #define CONFIG_SYS_EEPROM_BUS_NUM		0
130 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
131 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
132 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
133 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
134 
135 /*
136  * IFC Definitions
137  */
138 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
139 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
140 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
141 				CSPR_PORT_SIZE_16 | \
142 				CSPR_MSEL_NOR | \
143 				CSPR_V)
144 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
145 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
146 				+ 0x8000000) | \
147 				CSPR_PORT_SIZE_16 | \
148 				CSPR_MSEL_NOR | \
149 				CSPR_V)
150 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
151 
152 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
153 					CSOR_NOR_TRHZ_80)
154 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
155 					FTIM0_NOR_TEADC(0x5) | \
156 					FTIM0_NOR_TAVDS(0x6) | \
157 					FTIM0_NOR_TEAHC(0x5))
158 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
159 					FTIM1_NOR_TRAD_NOR(0x1a) | \
160 					FTIM1_NOR_TSEQRAD_NOR(0x13))
161 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x8) | \
162 					FTIM2_NOR_TCH(0x8) | \
163 					FTIM2_NOR_TWPH(0xe) | \
164 					FTIM2_NOR_TWP(0x1c))
165 #define CONFIG_SYS_NOR_FTIM3		0
166 
167 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
168 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
169 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
170 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
171 
172 #define CONFIG_SYS_FLASH_EMPTY_INFO
173 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
174 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
175 
176 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
177 #define CONFIG_SYS_WRITE_SWAPPED_DATA
178 
179 /*
180  * NAND Flash Definitions
181  */
182 #define CONFIG_NAND_FSL_IFC
183 
184 #define CONFIG_SYS_NAND_BASE		0x7e800000
185 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
186 
187 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
188 
189 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
190 				| CSPR_PORT_SIZE_8	\
191 				| CSPR_MSEL_NAND	\
192 				| CSPR_V)
193 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
194 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
195 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
196 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
197 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
198 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
199 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
200 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
201 
202 #define CONFIG_SYS_NAND_ONFI_DETECTION
203 
204 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
205 					FTIM0_NAND_TWP(0x18)   | \
206 					FTIM0_NAND_TWCHT(0x7) | \
207 					FTIM0_NAND_TWH(0xa))
208 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
209 					FTIM1_NAND_TWBE(0x39)  | \
210 					FTIM1_NAND_TRR(0xe)   | \
211 					FTIM1_NAND_TRP(0x18))
212 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
213 					FTIM2_NAND_TREH(0xa) | \
214 					FTIM2_NAND_TWHRE(0x1e))
215 #define CONFIG_SYS_NAND_FTIM3           0x0
216 
217 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
218 #define CONFIG_SYS_MAX_NAND_DEVICE	1
219 #define CONFIG_MTD_NAND_VERIFY_WRITE
220 
221 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
222 #endif
223 
224 #ifdef CONFIG_NAND_BOOT
225 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
226 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
227 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
228 #endif
229 
230 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
231 #define CONFIG_QIXIS_I2C_ACCESS
232 #define CONFIG_SYS_I2C_EARLY_INIT
233 #endif
234 
235 /*
236  * QIXIS Definitions
237  */
238 #define CONFIG_FSL_QIXIS
239 
240 #ifdef CONFIG_FSL_QIXIS
241 #define QIXIS_BASE			0x7fb00000
242 #define QIXIS_BASE_PHYS			QIXIS_BASE
243 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
244 #define QIXIS_LBMAP_SWITCH		6
245 #define QIXIS_LBMAP_MASK		0x0f
246 #define QIXIS_LBMAP_SHIFT		0
247 #define QIXIS_LBMAP_DFLTBANK		0x00
248 #define QIXIS_LBMAP_ALTBANK		0x04
249 #define QIXIS_LBMAP_NAND		0x09
250 #define QIXIS_LBMAP_SD			0x00
251 #define QIXIS_LBMAP_SD_QSPI		0xff
252 #define QIXIS_LBMAP_QSPI		0xff
253 #define QIXIS_RCW_SRC_NAND		0x110
254 #define QIXIS_RCW_SRC_SD		0x040
255 #define QIXIS_RCW_SRC_QSPI		0x045
256 #define QIXIS_RST_CTL_RESET		0x41
257 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
258 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
259 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
260 
261 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
262 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
263 					CSPR_PORT_SIZE_8 | \
264 					CSPR_MSEL_GPCM | \
265 					CSPR_V)
266 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
267 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
268 					CSOR_NOR_NOR_MODE_AVD_NOR | \
269 					CSOR_NOR_TRHZ_80)
270 
271 /*
272  * QIXIS Timing parameters for IFC GPCM
273  */
274 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
275 					FTIM0_GPCM_TEADC(0x20) | \
276 					FTIM0_GPCM_TEAHC(0x10))
277 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
278 					FTIM1_GPCM_TRAD(0x1f))
279 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
280 					FTIM2_GPCM_TCH(0x8) | \
281 					FTIM2_GPCM_TWP(0xf0))
282 #define CONFIG_SYS_FPGA_FTIM3		0x0
283 #endif
284 
285 #ifdef CONFIG_NAND_BOOT
286 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
287 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
288 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
289 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
290 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
291 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
292 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
293 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
294 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
295 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
296 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
297 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
298 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
299 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
300 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
301 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
302 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
303 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
304 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
305 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
306 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
307 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
308 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
309 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
310 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
311 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
312 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
313 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
314 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
315 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
316 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
317 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
318 #else
319 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
320 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
321 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
322 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
323 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
324 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
325 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
326 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
327 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
328 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
329 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
330 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
331 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
332 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
333 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
334 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
335 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
336 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
337 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
338 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
339 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
340 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
341 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
342 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
343 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
344 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
345 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
346 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
347 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
348 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
349 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
350 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
351 #endif
352 
353 /*
354  * I2C bus multiplexer
355  */
356 #define I2C_MUX_PCA_ADDR_PRI		0x77
357 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
358 #define I2C_RETIMER_ADDR		0x18
359 #define I2C_MUX_CH_DEFAULT		0x8
360 #define I2C_MUX_CH_CH7301		0xC
361 #define I2C_MUX_CH5			0xD
362 #define I2C_MUX_CH6			0xE
363 #define I2C_MUX_CH7			0xF
364 
365 #define I2C_MUX_CH_VOL_MONITOR 0xa
366 
367 /* Voltage monitor on channel 2*/
368 #define I2C_VOL_MONITOR_ADDR           0x40
369 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
370 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
371 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
372 
373 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
374 #ifndef CONFIG_SPL_BUILD
375 #define CONFIG_VID
376 #endif
377 #define CONFIG_VOL_MONITOR_IR36021_SET
378 #define CONFIG_VOL_MONITOR_INA220
379 /* The lowest and highest voltage allowed for LS1046AQDS */
380 #define VDD_MV_MIN			819
381 #define VDD_MV_MAX			1212
382 
383 /*
384  * Miscellaneous configurable options
385  */
386 
387 #define CONFIG_SYS_MEMTEST_START	0x80000000
388 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
389 
390 #define CONFIG_SYS_HZ			1000
391 
392 #define CONFIG_SYS_INIT_SP_OFFSET \
393 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
394 
395 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
396 
397 /*
398  * Environment
399  */
400 #define CONFIG_ENV_OVERWRITE
401 
402 #ifdef CONFIG_NAND_BOOT
403 #define CONFIG_ENV_SIZE			0x2000
404 #define CONFIG_ENV_OFFSET		(12 * CONFIG_SYS_NAND_BLOCK_SIZE)
405 #elif defined(CONFIG_SD_BOOT)
406 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
407 #define CONFIG_SYS_MMC_ENV_DEV		0
408 #define CONFIG_ENV_SIZE			0x2000
409 #elif defined(CONFIG_QSPI_BOOT)
410 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
411 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
412 #define CONFIG_ENV_SECT_SIZE		0x10000
413 #else
414 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
415 #define CONFIG_ENV_SECT_SIZE		0x20000
416 #define CONFIG_ENV_SIZE			0x20000
417 #endif
418 
419 #define CONFIG_CMDLINE_TAG
420 
421 #undef CONFIG_BOOTCOMMAND
422 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
423 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
424 					"e0000 f00000 && bootm $kernel_load"
425 #else
426 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
427 					"$kernel_size && bootm $kernel_load"
428 #endif
429 
430 #include <asm/fsl_secure_boot.h>
431 
432 #endif /* __LS1046AQDS_H__ */
433