xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 3788b451)
1 /*
2  * Copyright 2016 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046AQDS_H__
8 #define __LS1046AQDS_H__
9 
10 #include "ls1046a_common.h"
11 
12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
13 #define CONFIG_SYS_TEXT_BASE		0x82000000
14 #elif defined(CONFIG_QSPI_BOOT)
15 #define CONFIG_SYS_TEXT_BASE		0x40010000
16 #else
17 #define CONFIG_SYS_TEXT_BASE		0x60100000
18 #endif
19 
20 #ifndef __ASSEMBLY__
21 unsigned long get_board_sys_clk(void);
22 unsigned long get_board_ddr_clk(void);
23 #endif
24 
25 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
26 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
27 
28 #define CONFIG_SKIP_LOWLEVEL_INIT
29 
30 #define CONFIG_LAYERSCAPE_NS_ACCESS
31 
32 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
33 /* Physical Memory Map */
34 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
35 #define CONFIG_NR_DRAM_BANKS		2
36 
37 #define CONFIG_DDR_SPD
38 #define SPD_EEPROM_ADDRESS		0x51
39 #define CONFIG_SYS_SPD_BUS_NUM		0
40 
41 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
42 
43 #define CONFIG_DDR_ECC
44 #ifdef CONFIG_DDR_ECC
45 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
46 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
47 #endif
48 
49 /* DSPI */
50 #ifdef CONFIG_FSL_DSPI
51 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
52 #define CONFIG_SPI_FLASH_SST		/* cs1 */
53 #define CONFIG_SPI_FLASH_EON		/* cs2 */
54 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
55 #define CONFIG_SF_DEFAULT_BUS		1
56 #define CONFIG_SF_DEFAULT_CS		0
57 #endif
58 #endif
59 
60 /* QSPI */
61 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
62 #ifdef CONFIG_FSL_QSPI
63 #define CONFIG_SPI_FLASH_SPANSION
64 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
65 #define FSL_QSPI_FLASH_NUM		2
66 #endif
67 #endif
68 
69 #ifdef CONFIG_SYS_DPAA_FMAN
70 #define CONFIG_FMAN_ENET
71 #define CONFIG_PHYLIB
72 #define CONFIG_PHY_VITESSE
73 #define CONFIG_PHY_REALTEK
74 #define CONFIG_PHYLIB_10G
75 #define RGMII_PHY1_ADDR		0x1
76 #define RGMII_PHY2_ADDR		0x2
77 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
78 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
79 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
80 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
81 /* PHY address on QSGMII riser card on slot 2 */
82 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
83 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
84 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
85 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
86 #endif
87 
88 #ifdef CONFIG_RAMBOOT_PBL
89 #define CONFIG_SYS_FSL_PBL_PBI \
90 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
91 #endif
92 
93 #ifdef CONFIG_NAND_BOOT
94 #define CONFIG_SYS_FSL_PBL_RCW \
95 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
96 #endif
97 
98 #ifdef CONFIG_SD_BOOT
99 #ifdef CONFIG_SD_BOOT_QSPI
100 #define CONFIG_SYS_FSL_PBL_RCW \
101 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
102 #else
103 #define CONFIG_SYS_FSL_PBL_RCW \
104 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
105 #endif
106 #endif
107 
108 /* IFC */
109 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
110 #define	CONFIG_FSL_IFC
111 /*
112  * CONFIG_SYS_FLASH_BASE has the final address (core view)
113  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
114  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
115  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
116  */
117 #define CONFIG_SYS_FLASH_BASE			0x60000000
118 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
119 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
120 
121 #ifndef CONFIG_SYS_NO_FLASH
122 #define CONFIG_FLASH_CFI_DRIVER
123 #define CONFIG_SYS_FLASH_CFI
124 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
125 #define CONFIG_SYS_FLASH_QUIET_TEST
126 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
127 #endif
128 #endif
129 
130 /* LPUART */
131 #ifdef CONFIG_LPUART
132 #define CONFIG_LPUART_32B_REG
133 #define CFG_UART_MUX_MASK	0x6
134 #define CFG_UART_MUX_SHIFT	1
135 #define CFG_LPUART_EN		0x2
136 #endif
137 
138 /* SATA */
139 #define CONFIG_LIBATA
140 #define CONFIG_SCSI_AHCI
141 #define CONFIG_SCSI_AHCI_PLAT
142 #define CONFIG_SCSI
143 #define CONFIG_DOS_PARTITION
144 
145 #define CONFIG_PARTITION_UUIDS
146 #define CONFIG_EFI_PARTITION
147 #define CONFIG_CMD_GPT
148 
149 /* EEPROM */
150 #define CONFIG_ID_EEPROM
151 #define CONFIG_SYS_I2C_EEPROM_NXID
152 #define CONFIG_SYS_EEPROM_BUS_NUM		0
153 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
154 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
155 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
156 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
157 
158 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
159 
160 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
161 #define CONFIG_SYS_SCSI_MAX_LUN			1
162 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
163 						CONFIG_SYS_SCSI_MAX_LUN)
164 
165 /*
166  * IFC Definitions
167  */
168 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
169 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
170 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
171 				CSPR_PORT_SIZE_16 | \
172 				CSPR_MSEL_NOR | \
173 				CSPR_V)
174 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
175 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
176 				+ 0x8000000) | \
177 				CSPR_PORT_SIZE_16 | \
178 				CSPR_MSEL_NOR | \
179 				CSPR_V)
180 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
181 
182 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
183 					CSOR_NOR_TRHZ_80)
184 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
185 					FTIM0_NOR_TEADC(0x5) | \
186 					FTIM0_NOR_TEAHC(0x5))
187 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
188 					FTIM1_NOR_TRAD_NOR(0x1a) | \
189 					FTIM1_NOR_TSEQRAD_NOR(0x13))
190 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
191 					FTIM2_NOR_TCH(0x4) | \
192 					FTIM2_NOR_TWPH(0xe) | \
193 					FTIM2_NOR_TWP(0x1c))
194 #define CONFIG_SYS_NOR_FTIM3		0
195 
196 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
197 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
198 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
199 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
200 
201 #define CONFIG_SYS_FLASH_EMPTY_INFO
202 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
203 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
204 
205 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
206 #define CONFIG_SYS_WRITE_SWAPPED_DATA
207 
208 /*
209  * NAND Flash Definitions
210  */
211 #define CONFIG_NAND_FSL_IFC
212 
213 #define CONFIG_SYS_NAND_BASE		0x7e800000
214 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
215 
216 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
217 
218 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
219 				| CSPR_PORT_SIZE_8	\
220 				| CSPR_MSEL_NAND	\
221 				| CSPR_V)
222 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
223 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
224 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
225 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
226 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
227 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
228 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
229 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
230 
231 #define CONFIG_SYS_NAND_ONFI_DETECTION
232 
233 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
234 					FTIM0_NAND_TWP(0x18)   | \
235 					FTIM0_NAND_TWCHT(0x7) | \
236 					FTIM0_NAND_TWH(0xa))
237 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
238 					FTIM1_NAND_TWBE(0x39)  | \
239 					FTIM1_NAND_TRR(0xe)   | \
240 					FTIM1_NAND_TRP(0x18))
241 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
242 					FTIM2_NAND_TREH(0xa) | \
243 					FTIM2_NAND_TWHRE(0x1e))
244 #define CONFIG_SYS_NAND_FTIM3           0x0
245 
246 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
247 #define CONFIG_SYS_MAX_NAND_DEVICE	1
248 #define CONFIG_MTD_NAND_VERIFY_WRITE
249 #define CONFIG_CMD_NAND
250 
251 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
252 #endif
253 
254 #ifdef CONFIG_NAND_BOOT
255 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
256 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
257 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
258 #endif
259 
260 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
261 #define CONFIG_QIXIS_I2C_ACCESS
262 #define CONFIG_SYS_I2C_EARLY_INIT
263 #define CONFIG_SYS_NO_FLASH
264 #endif
265 
266 /*
267  * QIXIS Definitions
268  */
269 #define CONFIG_FSL_QIXIS
270 
271 #ifdef CONFIG_FSL_QIXIS
272 #define QIXIS_BASE			0x7fb00000
273 #define QIXIS_BASE_PHYS			QIXIS_BASE
274 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
275 #define QIXIS_LBMAP_SWITCH		6
276 #define QIXIS_LBMAP_MASK		0x0f
277 #define QIXIS_LBMAP_SHIFT		0
278 #define QIXIS_LBMAP_DFLTBANK		0x00
279 #define QIXIS_LBMAP_ALTBANK		0x04
280 #define QIXIS_LBMAP_NAND		0x09
281 #define QIXIS_LBMAP_SD			0x00
282 #define QIXIS_LBMAP_SD_QSPI		0xff
283 #define QIXIS_LBMAP_QSPI		0xff
284 #define QIXIS_RCW_SRC_NAND		0x110
285 #define QIXIS_RCW_SRC_SD		0x040
286 #define QIXIS_RCW_SRC_QSPI		0x045
287 #define QIXIS_RST_CTL_RESET		0x41
288 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
289 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
290 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
291 
292 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
293 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
294 					CSPR_PORT_SIZE_8 | \
295 					CSPR_MSEL_GPCM | \
296 					CSPR_V)
297 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
298 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
299 					CSOR_NOR_NOR_MODE_AVD_NOR | \
300 					CSOR_NOR_TRHZ_80)
301 
302 /*
303  * QIXIS Timing parameters for IFC GPCM
304  */
305 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
306 					FTIM0_GPCM_TEADC(0x20) | \
307 					FTIM0_GPCM_TEAHC(0x10))
308 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
309 					FTIM1_GPCM_TRAD(0x1f))
310 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
311 					FTIM2_GPCM_TCH(0x8) | \
312 					FTIM2_GPCM_TWP(0xf0))
313 #define CONFIG_SYS_FPGA_FTIM3		0x0
314 #endif
315 
316 #ifdef CONFIG_NAND_BOOT
317 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
318 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
319 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
320 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
321 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
322 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
323 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
324 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
325 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
326 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
327 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
328 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
329 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
330 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
331 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
332 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
333 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
334 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
335 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
336 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
337 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
338 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
339 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
340 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
341 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
342 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
343 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
344 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
345 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
346 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
347 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
348 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
349 #else
350 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
351 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
352 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
353 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
354 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
355 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
356 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
357 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
358 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
359 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
360 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
361 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
362 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
363 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
364 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
365 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
366 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
367 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
368 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
369 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
370 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
371 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
372 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
373 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
374 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
375 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
376 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
377 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
378 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
379 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
380 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
381 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
382 #endif
383 
384 /*
385  * I2C bus multiplexer
386  */
387 #define I2C_MUX_PCA_ADDR_PRI		0x77
388 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
389 #define I2C_RETIMER_ADDR		0x18
390 #define I2C_MUX_CH_DEFAULT		0x8
391 #define I2C_MUX_CH_CH7301		0xC
392 #define I2C_MUX_CH5			0xD
393 #define I2C_MUX_CH6			0xE
394 #define I2C_MUX_CH7			0xF
395 
396 #define I2C_MUX_CH_VOL_MONITOR 0xa
397 
398 /* Voltage monitor on channel 2*/
399 #define I2C_VOL_MONITOR_ADDR           0x40
400 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
401 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
402 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
403 
404 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
405 #ifndef CONFIG_SPL_BUILD
406 #define CONFIG_VID
407 #endif
408 #define CONFIG_VOL_MONITOR_IR36021_SET
409 #define CONFIG_VOL_MONITOR_INA220
410 /* The lowest and highest voltage allowed for LS1046AQDS */
411 #define VDD_MV_MIN			819
412 #define VDD_MV_MAX			1212
413 
414 /*
415  * Miscellaneous configurable options
416  */
417 #define CONFIG_MISC_INIT_R
418 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
419 #define CONFIG_AUTO_COMPLETE
420 #define CONFIG_SYS_PBSIZE		\
421 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
422 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
423 
424 #define CONFIG_SYS_MEMTEST_START	0x80000000
425 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
426 
427 #define CONFIG_SYS_HZ			1000
428 
429 /*
430  * Stack sizes
431  * The stack sizes are set up in start.S using the settings below
432  */
433 #define CONFIG_STACKSIZE		(30 * 1024)
434 
435 #define CONFIG_SYS_INIT_SP_OFFSET \
436 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
437 
438 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
439 
440 /*
441  * Environment
442  */
443 #define CONFIG_ENV_OVERWRITE
444 
445 #ifdef CONFIG_NAND_BOOT
446 #define CONFIG_ENV_IS_IN_NAND
447 #define CONFIG_ENV_SIZE			0x2000
448 #define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
449 #elif defined(CONFIG_SD_BOOT)
450 #define CONFIG_ENV_OFFSET		(1024 * 1024)
451 #define CONFIG_ENV_IS_IN_MMC
452 #define CONFIG_SYS_MMC_ENV_DEV		0
453 #define CONFIG_ENV_SIZE			0x2000
454 #elif defined(CONFIG_QSPI_BOOT)
455 #define CONFIG_ENV_IS_IN_SPI_FLASH
456 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
457 #define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
458 #define CONFIG_ENV_SECT_SIZE		0x10000
459 #else
460 #define CONFIG_ENV_IS_IN_FLASH
461 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
462 #define CONFIG_ENV_SECT_SIZE		0x20000
463 #define CONFIG_ENV_SIZE			0x20000
464 #endif
465 
466 #define CONFIG_CMDLINE_TAG
467 
468 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
469 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
470 					"e0000 f00000 && bootm $kernel_load"
471 #else
472 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
473 					"$kernel_size && bootm $kernel_load"
474 #endif
475 
476 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
477 #define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
478 			"14m(free)"
479 #else
480 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \
481 			"1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \
482 			"1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \
483 			"1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \
484 			"1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \
485 			"40m(nor_bank4_fit);7e800000.flash:" \
486 			"4m(nand_uboot),36m(nand_kernel)," \
487 			"472m(nand_free);spi0.0:2m(uboot)," \
488 			"14m(free)"
489 #endif
490 
491 #include <asm/fsl_secure_boot.h>
492 
493 #endif /* __LS1046AQDS_H__ */
494