xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 193f6fb9)
1 /*
2  * Copyright 2016 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046AQDS_H__
8 #define __LS1046AQDS_H__
9 
10 #include "ls1046a_common.h"
11 
12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
13 #define CONFIG_SYS_TEXT_BASE		0x82000000
14 #elif defined(CONFIG_QSPI_BOOT)
15 #define CONFIG_SYS_TEXT_BASE		0x40100000
16 #else
17 #define CONFIG_SYS_TEXT_BASE		0x60100000
18 #endif
19 
20 #ifndef __ASSEMBLY__
21 unsigned long get_board_sys_clk(void);
22 unsigned long get_board_ddr_clk(void);
23 #endif
24 
25 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
26 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
27 
28 #define CONFIG_SKIP_LOWLEVEL_INIT
29 
30 #define CONFIG_LAYERSCAPE_NS_ACCESS
31 
32 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
33 /* Physical Memory Map */
34 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
35 #define CONFIG_NR_DRAM_BANKS		2
36 
37 #define CONFIG_DDR_SPD
38 #define SPD_EEPROM_ADDRESS		0x51
39 #define CONFIG_SYS_SPD_BUS_NUM		0
40 
41 #ifndef CONFIG_SPL
42 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
43 #endif
44 
45 #define CONFIG_DDR_ECC
46 #ifdef CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
49 #endif
50 
51 /* DSPI */
52 #ifdef CONFIG_FSL_DSPI
53 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
54 #define CONFIG_SPI_FLASH_SST		/* cs1 */
55 #define CONFIG_SPI_FLASH_EON		/* cs2 */
56 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
57 #define CONFIG_SF_DEFAULT_BUS		1
58 #define CONFIG_SF_DEFAULT_CS		0
59 #endif
60 #endif
61 
62 /* QSPI */
63 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
64 #ifdef CONFIG_FSL_QSPI
65 #define CONFIG_SPI_FLASH_SPANSION
66 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
67 #define FSL_QSPI_FLASH_NUM		2
68 #endif
69 #endif
70 
71 #ifdef CONFIG_SYS_DPAA_FMAN
72 #define CONFIG_FMAN_ENET
73 #define CONFIG_PHY_VITESSE
74 #define CONFIG_PHY_REALTEK
75 #define CONFIG_PHYLIB_10G
76 #define RGMII_PHY1_ADDR		0x1
77 #define RGMII_PHY2_ADDR		0x2
78 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
79 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
80 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
81 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
82 /* PHY address on QSGMII riser card on slot 2 */
83 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
84 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
85 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
86 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
87 #endif
88 
89 #ifdef CONFIG_RAMBOOT_PBL
90 #define CONFIG_SYS_FSL_PBL_PBI \
91 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
92 #endif
93 
94 #ifdef CONFIG_NAND_BOOT
95 #define CONFIG_SYS_FSL_PBL_RCW \
96 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
97 #endif
98 
99 #ifdef CONFIG_SD_BOOT
100 #ifdef CONFIG_SD_BOOT_QSPI
101 #define CONFIG_SYS_FSL_PBL_RCW \
102 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
103 #else
104 #define CONFIG_SYS_FSL_PBL_RCW \
105 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
106 #endif
107 #endif
108 
109 /* IFC */
110 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
111 #define	CONFIG_FSL_IFC
112 /*
113  * CONFIG_SYS_FLASH_BASE has the final address (core view)
114  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
115  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
116  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
117  */
118 #define CONFIG_SYS_FLASH_BASE			0x60000000
119 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
120 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
121 
122 #ifdef CONFIG_MTD_NOR_FLASH
123 #define CONFIG_FLASH_CFI_DRIVER
124 #define CONFIG_SYS_FLASH_CFI
125 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
126 #define CONFIG_SYS_FLASH_QUIET_TEST
127 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
128 #endif
129 #endif
130 
131 /* LPUART */
132 #ifdef CONFIG_LPUART
133 #define CONFIG_LPUART_32B_REG
134 #define CFG_UART_MUX_MASK	0x6
135 #define CFG_UART_MUX_SHIFT	1
136 #define CFG_LPUART_EN		0x2
137 #endif
138 
139 /* SATA */
140 #define CONFIG_SCSI_AHCI_PLAT
141 
142 /* EEPROM */
143 #define CONFIG_ID_EEPROM
144 #define CONFIG_SYS_I2C_EEPROM_NXID
145 #define CONFIG_SYS_EEPROM_BUS_NUM		0
146 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
147 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
148 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
149 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
150 
151 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
152 
153 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
154 #define CONFIG_SYS_SCSI_MAX_LUN			1
155 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
156 						CONFIG_SYS_SCSI_MAX_LUN)
157 
158 /*
159  * IFC Definitions
160  */
161 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
162 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
163 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
164 				CSPR_PORT_SIZE_16 | \
165 				CSPR_MSEL_NOR | \
166 				CSPR_V)
167 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
168 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
169 				+ 0x8000000) | \
170 				CSPR_PORT_SIZE_16 | \
171 				CSPR_MSEL_NOR | \
172 				CSPR_V)
173 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
174 
175 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
176 					CSOR_NOR_TRHZ_80)
177 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
178 					FTIM0_NOR_TEADC(0x5) | \
179 					FTIM0_NOR_TAVDS(0x6) | \
180 					FTIM0_NOR_TEAHC(0x5))
181 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
182 					FTIM1_NOR_TRAD_NOR(0x1a) | \
183 					FTIM1_NOR_TSEQRAD_NOR(0x13))
184 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x8) | \
185 					FTIM2_NOR_TCH(0x8) | \
186 					FTIM2_NOR_TWPH(0xe) | \
187 					FTIM2_NOR_TWP(0x1c))
188 #define CONFIG_SYS_NOR_FTIM3		0
189 
190 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
191 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
192 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
193 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
194 
195 #define CONFIG_SYS_FLASH_EMPTY_INFO
196 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
197 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
198 
199 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
200 #define CONFIG_SYS_WRITE_SWAPPED_DATA
201 
202 /*
203  * NAND Flash Definitions
204  */
205 #define CONFIG_NAND_FSL_IFC
206 
207 #define CONFIG_SYS_NAND_BASE		0x7e800000
208 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
209 
210 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
211 
212 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
213 				| CSPR_PORT_SIZE_8	\
214 				| CSPR_MSEL_NAND	\
215 				| CSPR_V)
216 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
217 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
218 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
219 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
220 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
221 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
222 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
223 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
224 
225 #define CONFIG_SYS_NAND_ONFI_DETECTION
226 
227 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
228 					FTIM0_NAND_TWP(0x18)   | \
229 					FTIM0_NAND_TWCHT(0x7) | \
230 					FTIM0_NAND_TWH(0xa))
231 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
232 					FTIM1_NAND_TWBE(0x39)  | \
233 					FTIM1_NAND_TRR(0xe)   | \
234 					FTIM1_NAND_TRP(0x18))
235 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
236 					FTIM2_NAND_TREH(0xa) | \
237 					FTIM2_NAND_TWHRE(0x1e))
238 #define CONFIG_SYS_NAND_FTIM3           0x0
239 
240 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
241 #define CONFIG_SYS_MAX_NAND_DEVICE	1
242 #define CONFIG_MTD_NAND_VERIFY_WRITE
243 
244 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
245 #endif
246 
247 #ifdef CONFIG_NAND_BOOT
248 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
249 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
250 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
251 #endif
252 
253 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
254 #define CONFIG_QIXIS_I2C_ACCESS
255 #define CONFIG_SYS_I2C_EARLY_INIT
256 #endif
257 
258 /*
259  * QIXIS Definitions
260  */
261 #define CONFIG_FSL_QIXIS
262 
263 #ifdef CONFIG_FSL_QIXIS
264 #define QIXIS_BASE			0x7fb00000
265 #define QIXIS_BASE_PHYS			QIXIS_BASE
266 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
267 #define QIXIS_LBMAP_SWITCH		6
268 #define QIXIS_LBMAP_MASK		0x0f
269 #define QIXIS_LBMAP_SHIFT		0
270 #define QIXIS_LBMAP_DFLTBANK		0x00
271 #define QIXIS_LBMAP_ALTBANK		0x04
272 #define QIXIS_LBMAP_NAND		0x09
273 #define QIXIS_LBMAP_SD			0x00
274 #define QIXIS_LBMAP_SD_QSPI		0xff
275 #define QIXIS_LBMAP_QSPI		0xff
276 #define QIXIS_RCW_SRC_NAND		0x110
277 #define QIXIS_RCW_SRC_SD		0x040
278 #define QIXIS_RCW_SRC_QSPI		0x045
279 #define QIXIS_RST_CTL_RESET		0x41
280 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
281 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
282 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
283 
284 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
285 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
286 					CSPR_PORT_SIZE_8 | \
287 					CSPR_MSEL_GPCM | \
288 					CSPR_V)
289 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
290 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
291 					CSOR_NOR_NOR_MODE_AVD_NOR | \
292 					CSOR_NOR_TRHZ_80)
293 
294 /*
295  * QIXIS Timing parameters for IFC GPCM
296  */
297 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
298 					FTIM0_GPCM_TEADC(0x20) | \
299 					FTIM0_GPCM_TEAHC(0x10))
300 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
301 					FTIM1_GPCM_TRAD(0x1f))
302 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
303 					FTIM2_GPCM_TCH(0x8) | \
304 					FTIM2_GPCM_TWP(0xf0))
305 #define CONFIG_SYS_FPGA_FTIM3		0x0
306 #endif
307 
308 #ifdef CONFIG_NAND_BOOT
309 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
310 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
311 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
312 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
313 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
314 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
315 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
316 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
317 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
318 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
319 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
320 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
321 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
322 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
323 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
324 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
325 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
326 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
327 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
328 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
329 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
330 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
331 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
332 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
333 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
334 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
335 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
336 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
337 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
338 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
339 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
340 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
341 #else
342 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
343 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
344 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
345 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
346 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
347 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
348 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
349 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
350 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
351 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
352 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
353 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
354 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
355 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
356 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
357 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
358 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
359 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
360 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
361 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
362 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
363 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
364 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
365 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
366 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
367 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
368 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
369 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
370 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
371 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
372 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
373 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
374 #endif
375 
376 /*
377  * I2C bus multiplexer
378  */
379 #define I2C_MUX_PCA_ADDR_PRI		0x77
380 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
381 #define I2C_RETIMER_ADDR		0x18
382 #define I2C_MUX_CH_DEFAULT		0x8
383 #define I2C_MUX_CH_CH7301		0xC
384 #define I2C_MUX_CH5			0xD
385 #define I2C_MUX_CH6			0xE
386 #define I2C_MUX_CH7			0xF
387 
388 #define I2C_MUX_CH_VOL_MONITOR 0xa
389 
390 /* Voltage monitor on channel 2*/
391 #define I2C_VOL_MONITOR_ADDR           0x40
392 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
393 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
394 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
395 
396 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
397 #ifndef CONFIG_SPL_BUILD
398 #define CONFIG_VID
399 #endif
400 #define CONFIG_VOL_MONITOR_IR36021_SET
401 #define CONFIG_VOL_MONITOR_INA220
402 /* The lowest and highest voltage allowed for LS1046AQDS */
403 #define VDD_MV_MIN			819
404 #define VDD_MV_MAX			1212
405 
406 /*
407  * Miscellaneous configurable options
408  */
409 #define CONFIG_MISC_INIT_R
410 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
411 #define CONFIG_AUTO_COMPLETE
412 
413 #define CONFIG_SYS_MEMTEST_START	0x80000000
414 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
415 
416 #define CONFIG_SYS_HZ			1000
417 
418 #define CONFIG_SYS_INIT_SP_OFFSET \
419 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
420 
421 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
422 
423 /*
424  * Environment
425  */
426 #define CONFIG_ENV_OVERWRITE
427 
428 #ifdef CONFIG_NAND_BOOT
429 #define CONFIG_ENV_SIZE			0x2000
430 #define CONFIG_ENV_OFFSET		(12 * CONFIG_SYS_NAND_BLOCK_SIZE)
431 #elif defined(CONFIG_SD_BOOT)
432 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
433 #define CONFIG_SYS_MMC_ENV_DEV		0
434 #define CONFIG_ENV_SIZE			0x2000
435 #elif defined(CONFIG_QSPI_BOOT)
436 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
437 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
438 #define CONFIG_ENV_SECT_SIZE		0x10000
439 #else
440 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
441 #define CONFIG_ENV_SECT_SIZE		0x20000
442 #define CONFIG_ENV_SIZE			0x20000
443 #endif
444 
445 #define CONFIG_CMDLINE_TAG
446 
447 #undef CONFIG_BOOTCOMMAND
448 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
449 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
450 					"e0000 f00000 && bootm $kernel_load"
451 #else
452 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
453 					"$kernel_size && bootm $kernel_load"
454 #endif
455 
456 #include <asm/fsl_secure_boot.h>
457 
458 #endif /* __LS1046AQDS_H__ */
459