xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 0649cd0d)
1 /*
2  * Copyright 2016 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046AQDS_H__
8 #define __LS1046AQDS_H__
9 
10 #include "ls1046a_common.h"
11 
12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
13 #define CONFIG_SYS_TEXT_BASE		0x82000000
14 #elif defined(CONFIG_QSPI_BOOT)
15 #define CONFIG_SYS_TEXT_BASE		0x40100000
16 #else
17 #define CONFIG_SYS_TEXT_BASE		0x60100000
18 #endif
19 
20 #ifndef __ASSEMBLY__
21 unsigned long get_board_sys_clk(void);
22 unsigned long get_board_ddr_clk(void);
23 #endif
24 
25 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
26 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
27 
28 #define CONFIG_SKIP_LOWLEVEL_INIT
29 
30 #define CONFIG_LAYERSCAPE_NS_ACCESS
31 
32 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
33 /* Physical Memory Map */
34 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
35 #define CONFIG_NR_DRAM_BANKS		2
36 
37 #define CONFIG_DDR_SPD
38 #define SPD_EEPROM_ADDRESS		0x51
39 #define CONFIG_SYS_SPD_BUS_NUM		0
40 
41 #ifndef CONFIG_SPL
42 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
43 #endif
44 
45 #define CONFIG_DDR_ECC
46 #ifdef CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
49 #endif
50 
51 /* DSPI */
52 #ifdef CONFIG_FSL_DSPI
53 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
54 #define CONFIG_SPI_FLASH_SST		/* cs1 */
55 #define CONFIG_SPI_FLASH_EON		/* cs2 */
56 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
57 #define CONFIG_SF_DEFAULT_BUS		1
58 #define CONFIG_SF_DEFAULT_CS		0
59 #endif
60 #endif
61 
62 /* QSPI */
63 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
64 #ifdef CONFIG_FSL_QSPI
65 #define CONFIG_SPI_FLASH_SPANSION
66 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
67 #define FSL_QSPI_FLASH_NUM		2
68 #endif
69 #endif
70 
71 #ifdef CONFIG_SYS_DPAA_FMAN
72 #define CONFIG_FMAN_ENET
73 #define CONFIG_PHY_VITESSE
74 #define CONFIG_PHY_REALTEK
75 #define CONFIG_PHYLIB_10G
76 #define RGMII_PHY1_ADDR		0x1
77 #define RGMII_PHY2_ADDR		0x2
78 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
79 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
80 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
81 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
82 /* PHY address on QSGMII riser card on slot 2 */
83 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
84 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
85 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
86 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
87 #endif
88 
89 #ifdef CONFIG_RAMBOOT_PBL
90 #define CONFIG_SYS_FSL_PBL_PBI \
91 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
92 #endif
93 
94 #ifdef CONFIG_NAND_BOOT
95 #define CONFIG_SYS_FSL_PBL_RCW \
96 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
97 #endif
98 
99 #ifdef CONFIG_SD_BOOT
100 #ifdef CONFIG_SD_BOOT_QSPI
101 #define CONFIG_SYS_FSL_PBL_RCW \
102 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
103 #else
104 #define CONFIG_SYS_FSL_PBL_RCW \
105 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
106 #endif
107 #endif
108 
109 /* IFC */
110 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
111 #define	CONFIG_FSL_IFC
112 /*
113  * CONFIG_SYS_FLASH_BASE has the final address (core view)
114  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
115  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
116  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
117  */
118 #define CONFIG_SYS_FLASH_BASE			0x60000000
119 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
120 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
121 
122 #ifdef CONFIG_MTD_NOR_FLASH
123 #define CONFIG_FLASH_CFI_DRIVER
124 #define CONFIG_SYS_FLASH_CFI
125 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
126 #define CONFIG_SYS_FLASH_QUIET_TEST
127 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
128 #endif
129 #endif
130 
131 /* LPUART */
132 #ifdef CONFIG_LPUART
133 #define CONFIG_LPUART_32B_REG
134 #define CFG_UART_MUX_MASK	0x6
135 #define CFG_UART_MUX_SHIFT	1
136 #define CFG_LPUART_EN		0x2
137 #endif
138 
139 /* USB */
140 #define CONFIG_HAS_FSL_XHCI_USB
141 #ifdef CONFIG_HAS_FSL_XHCI_USB
142 #define CONFIG_USB_XHCI_HCD
143 #define CONFIG_USB_XHCI_FSL
144 #define CONFIG_USB_XHCI_DWC3
145 #define CONFIG_USB_MAX_CONTROLLER_COUNT         3
146 #define CONFIG_USB_STORAGE
147 #endif
148 
149 /* SATA */
150 #define CONFIG_LIBATA
151 #define CONFIG_SCSI_AHCI
152 #define CONFIG_SCSI_AHCI_PLAT
153 
154 /* EEPROM */
155 #define CONFIG_ID_EEPROM
156 #define CONFIG_SYS_I2C_EEPROM_NXID
157 #define CONFIG_SYS_EEPROM_BUS_NUM		0
158 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
159 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
160 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
161 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
162 
163 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
164 
165 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
166 #define CONFIG_SYS_SCSI_MAX_LUN			1
167 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
168 						CONFIG_SYS_SCSI_MAX_LUN)
169 
170 /*
171  * IFC Definitions
172  */
173 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
174 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
175 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
176 				CSPR_PORT_SIZE_16 | \
177 				CSPR_MSEL_NOR | \
178 				CSPR_V)
179 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
180 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
181 				+ 0x8000000) | \
182 				CSPR_PORT_SIZE_16 | \
183 				CSPR_MSEL_NOR | \
184 				CSPR_V)
185 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
186 
187 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
188 					CSOR_NOR_TRHZ_80)
189 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
190 					FTIM0_NOR_TEADC(0x5) | \
191 					FTIM0_NOR_TEAHC(0x5))
192 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
193 					FTIM1_NOR_TRAD_NOR(0x1a) | \
194 					FTIM1_NOR_TSEQRAD_NOR(0x13))
195 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
196 					FTIM2_NOR_TCH(0x4) | \
197 					FTIM2_NOR_TWPH(0xe) | \
198 					FTIM2_NOR_TWP(0x1c))
199 #define CONFIG_SYS_NOR_FTIM3		0
200 
201 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
202 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
203 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
204 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
205 
206 #define CONFIG_SYS_FLASH_EMPTY_INFO
207 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
208 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
209 
210 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
211 #define CONFIG_SYS_WRITE_SWAPPED_DATA
212 
213 /*
214  * NAND Flash Definitions
215  */
216 #define CONFIG_NAND_FSL_IFC
217 
218 #define CONFIG_SYS_NAND_BASE		0x7e800000
219 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
220 
221 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
222 
223 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
224 				| CSPR_PORT_SIZE_8	\
225 				| CSPR_MSEL_NAND	\
226 				| CSPR_V)
227 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
228 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
229 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
230 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
231 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
232 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
233 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
234 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
235 
236 #define CONFIG_SYS_NAND_ONFI_DETECTION
237 
238 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
239 					FTIM0_NAND_TWP(0x18)   | \
240 					FTIM0_NAND_TWCHT(0x7) | \
241 					FTIM0_NAND_TWH(0xa))
242 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
243 					FTIM1_NAND_TWBE(0x39)  | \
244 					FTIM1_NAND_TRR(0xe)   | \
245 					FTIM1_NAND_TRP(0x18))
246 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
247 					FTIM2_NAND_TREH(0xa) | \
248 					FTIM2_NAND_TWHRE(0x1e))
249 #define CONFIG_SYS_NAND_FTIM3           0x0
250 
251 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
252 #define CONFIG_SYS_MAX_NAND_DEVICE	1
253 #define CONFIG_MTD_NAND_VERIFY_WRITE
254 
255 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
256 #endif
257 
258 #ifdef CONFIG_NAND_BOOT
259 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
260 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
261 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
262 #endif
263 
264 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
265 #define CONFIG_QIXIS_I2C_ACCESS
266 #define CONFIG_SYS_I2C_EARLY_INIT
267 #endif
268 
269 /*
270  * QIXIS Definitions
271  */
272 #define CONFIG_FSL_QIXIS
273 
274 #ifdef CONFIG_FSL_QIXIS
275 #define QIXIS_BASE			0x7fb00000
276 #define QIXIS_BASE_PHYS			QIXIS_BASE
277 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
278 #define QIXIS_LBMAP_SWITCH		6
279 #define QIXIS_LBMAP_MASK		0x0f
280 #define QIXIS_LBMAP_SHIFT		0
281 #define QIXIS_LBMAP_DFLTBANK		0x00
282 #define QIXIS_LBMAP_ALTBANK		0x04
283 #define QIXIS_LBMAP_NAND		0x09
284 #define QIXIS_LBMAP_SD			0x00
285 #define QIXIS_LBMAP_SD_QSPI		0xff
286 #define QIXIS_LBMAP_QSPI		0xff
287 #define QIXIS_RCW_SRC_NAND		0x110
288 #define QIXIS_RCW_SRC_SD		0x040
289 #define QIXIS_RCW_SRC_QSPI		0x045
290 #define QIXIS_RST_CTL_RESET		0x41
291 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
292 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
293 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
294 
295 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
296 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
297 					CSPR_PORT_SIZE_8 | \
298 					CSPR_MSEL_GPCM | \
299 					CSPR_V)
300 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
301 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
302 					CSOR_NOR_NOR_MODE_AVD_NOR | \
303 					CSOR_NOR_TRHZ_80)
304 
305 /*
306  * QIXIS Timing parameters for IFC GPCM
307  */
308 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
309 					FTIM0_GPCM_TEADC(0x20) | \
310 					FTIM0_GPCM_TEAHC(0x10))
311 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
312 					FTIM1_GPCM_TRAD(0x1f))
313 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
314 					FTIM2_GPCM_TCH(0x8) | \
315 					FTIM2_GPCM_TWP(0xf0))
316 #define CONFIG_SYS_FPGA_FTIM3		0x0
317 #endif
318 
319 #ifdef CONFIG_NAND_BOOT
320 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
321 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
322 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
323 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
324 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
325 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
326 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
327 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
328 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
329 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
330 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
331 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
332 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
333 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
334 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
335 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
336 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
337 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
338 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
339 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
340 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
341 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
342 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
343 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
344 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
345 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
346 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
347 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
348 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
349 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
350 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
351 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
352 #else
353 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
354 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
355 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
356 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
357 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
358 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
359 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
360 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
361 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
362 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
363 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
364 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
365 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
366 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
367 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
368 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
369 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
370 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
371 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
372 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
373 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
374 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
375 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
376 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
377 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
378 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
379 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
380 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
381 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
382 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
383 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
384 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
385 #endif
386 
387 /*
388  * I2C bus multiplexer
389  */
390 #define I2C_MUX_PCA_ADDR_PRI		0x77
391 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
392 #define I2C_RETIMER_ADDR		0x18
393 #define I2C_MUX_CH_DEFAULT		0x8
394 #define I2C_MUX_CH_CH7301		0xC
395 #define I2C_MUX_CH5			0xD
396 #define I2C_MUX_CH6			0xE
397 #define I2C_MUX_CH7			0xF
398 
399 #define I2C_MUX_CH_VOL_MONITOR 0xa
400 
401 /* Voltage monitor on channel 2*/
402 #define I2C_VOL_MONITOR_ADDR           0x40
403 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
404 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
405 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
406 
407 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
408 #ifndef CONFIG_SPL_BUILD
409 #define CONFIG_VID
410 #endif
411 #define CONFIG_VOL_MONITOR_IR36021_SET
412 #define CONFIG_VOL_MONITOR_INA220
413 /* The lowest and highest voltage allowed for LS1046AQDS */
414 #define VDD_MV_MIN			819
415 #define VDD_MV_MAX			1212
416 
417 /*
418  * Miscellaneous configurable options
419  */
420 #define CONFIG_MISC_INIT_R
421 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
422 #define CONFIG_AUTO_COMPLETE
423 #define CONFIG_SYS_PBSIZE		\
424 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
425 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
426 
427 #define CONFIG_SYS_MEMTEST_START	0x80000000
428 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
429 
430 #define CONFIG_SYS_HZ			1000
431 
432 #define CONFIG_SYS_INIT_SP_OFFSET \
433 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
434 
435 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
436 
437 /*
438  * Environment
439  */
440 #define CONFIG_ENV_OVERWRITE
441 
442 #ifdef CONFIG_NAND_BOOT
443 #define CONFIG_ENV_SIZE			0x2000
444 #define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
445 #elif defined(CONFIG_SD_BOOT)
446 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
447 #define CONFIG_SYS_MMC_ENV_DEV		0
448 #define CONFIG_ENV_SIZE			0x2000
449 #elif defined(CONFIG_QSPI_BOOT)
450 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
451 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
452 #define CONFIG_ENV_SECT_SIZE		0x10000
453 #else
454 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
455 #define CONFIG_ENV_SECT_SIZE		0x20000
456 #define CONFIG_ENV_SIZE			0x20000
457 #endif
458 
459 #define CONFIG_CMDLINE_TAG
460 
461 #undef CONFIG_BOOTCOMMAND
462 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
463 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
464 					"e0000 f00000 && bootm $kernel_load"
465 #else
466 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
467 					"$kernel_size && bootm $kernel_load"
468 #endif
469 
470 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
471 #define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
472 			"14m(free)"
473 #else
474 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \
475 			"2m@0x100000(nor_bank0_uboot),"\
476 			"40m@0x1100000(nor_bank0_fit)," \
477 			"7m(nor_bank0_user)," \
478 			"2m@0x4100000(nor_bank4_uboot)," \
479 			"40m@0x5100000(nor_bank4_fit),"\
480 			"-(nor_bank4_user);" \
481 			"7e800000.flash:" \
482 			"4m(nand_uboot),36m(nand_kernel)," \
483 			"472m(nand_free);spi0.0:2m(uboot)," \
484 			"14m(free)"
485 #endif
486 
487 #include <asm/fsl_secure_boot.h>
488 
489 #endif /* __LS1046AQDS_H__ */
490