xref: /openbmc/u-boot/include/configs/ls1046aqds.h (revision 0645c23a)
1 /*
2  * Copyright 2016 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046AQDS_H__
8 #define __LS1046AQDS_H__
9 
10 #include "ls1046a_common.h"
11 
12 #if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
13 #define CONFIG_SYS_TEXT_BASE		0x82000000
14 #elif defined(CONFIG_QSPI_BOOT)
15 #define CONFIG_SYS_TEXT_BASE		0x40010000
16 #else
17 #define CONFIG_SYS_TEXT_BASE		0x60100000
18 #endif
19 
20 #ifndef __ASSEMBLY__
21 unsigned long get_board_sys_clk(void);
22 unsigned long get_board_ddr_clk(void);
23 #endif
24 
25 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
26 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
27 
28 #define CONFIG_SKIP_LOWLEVEL_INIT
29 
30 #define CONFIG_LAYERSCAPE_NS_ACCESS
31 
32 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
33 /* Physical Memory Map */
34 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
35 #define CONFIG_NR_DRAM_BANKS		2
36 
37 #define CONFIG_DDR_SPD
38 #define SPD_EEPROM_ADDRESS		0x51
39 #define CONFIG_SYS_SPD_BUS_NUM		0
40 
41 #ifndef CONFIG_SPL
42 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
43 #endif
44 
45 #define CONFIG_DDR_ECC
46 #ifdef CONFIG_DDR_ECC
47 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
48 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
49 #endif
50 
51 /* DSPI */
52 #ifdef CONFIG_FSL_DSPI
53 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
54 #define CONFIG_SPI_FLASH_SST		/* cs1 */
55 #define CONFIG_SPI_FLASH_EON		/* cs2 */
56 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
57 #define CONFIG_SF_DEFAULT_BUS		1
58 #define CONFIG_SF_DEFAULT_CS		0
59 #endif
60 #endif
61 
62 /* QSPI */
63 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
64 #ifdef CONFIG_FSL_QSPI
65 #define CONFIG_SPI_FLASH_SPANSION
66 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
67 #define FSL_QSPI_FLASH_NUM		2
68 #endif
69 #endif
70 
71 #ifdef CONFIG_SYS_DPAA_FMAN
72 #define CONFIG_FMAN_ENET
73 #define CONFIG_PHYLIB
74 #define CONFIG_PHY_VITESSE
75 #define CONFIG_PHY_REALTEK
76 #define CONFIG_PHYLIB_10G
77 #define RGMII_PHY1_ADDR		0x1
78 #define RGMII_PHY2_ADDR		0x2
79 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
80 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
81 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
82 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
83 /* PHY address on QSGMII riser card on slot 2 */
84 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
85 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
86 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
87 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
88 #endif
89 
90 #ifdef CONFIG_RAMBOOT_PBL
91 #define CONFIG_SYS_FSL_PBL_PBI \
92 	board/freescale/ls1046aqds/ls1046aqds_pbi.cfg
93 #endif
94 
95 #ifdef CONFIG_NAND_BOOT
96 #define CONFIG_SYS_FSL_PBL_RCW \
97 	board/freescale/ls1046aqds/ls1046aqds_rcw_nand.cfg
98 #endif
99 
100 #ifdef CONFIG_SD_BOOT
101 #ifdef CONFIG_SD_BOOT_QSPI
102 #define CONFIG_SYS_FSL_PBL_RCW \
103 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_qspi.cfg
104 #else
105 #define CONFIG_SYS_FSL_PBL_RCW \
106 	board/freescale/ls1046aqds/ls1046aqds_rcw_sd_ifc.cfg
107 #endif
108 #endif
109 
110 /* IFC */
111 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
112 #define	CONFIG_FSL_IFC
113 /*
114  * CONFIG_SYS_FLASH_BASE has the final address (core view)
115  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
116  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
117  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
118  */
119 #define CONFIG_SYS_FLASH_BASE			0x60000000
120 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
121 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
122 
123 #ifdef CONFIG_MTD_NOR_FLASH
124 #define CONFIG_FLASH_CFI_DRIVER
125 #define CONFIG_SYS_FLASH_CFI
126 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
127 #define CONFIG_SYS_FLASH_QUIET_TEST
128 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
129 #endif
130 #endif
131 
132 /* LPUART */
133 #ifdef CONFIG_LPUART
134 #define CONFIG_LPUART_32B_REG
135 #define CFG_UART_MUX_MASK	0x6
136 #define CFG_UART_MUX_SHIFT	1
137 #define CFG_LPUART_EN		0x2
138 #endif
139 
140 /* USB */
141 #define CONFIG_HAS_FSL_XHCI_USB
142 #ifdef CONFIG_HAS_FSL_XHCI_USB
143 #define CONFIG_USB_XHCI_HCD
144 #define CONFIG_USB_XHCI_FSL
145 #define CONFIG_USB_XHCI_DWC3
146 #define CONFIG_USB_MAX_CONTROLLER_COUNT         3
147 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
148 #define CONFIG_CMD_USB
149 #define CONFIG_USB_STORAGE
150 #endif
151 
152 /* SATA */
153 #define CONFIG_LIBATA
154 #define CONFIG_SCSI_AHCI
155 #define CONFIG_SCSI_AHCI_PLAT
156 #define CONFIG_SCSI
157 
158 /* EEPROM */
159 #define CONFIG_ID_EEPROM
160 #define CONFIG_SYS_I2C_EEPROM_NXID
161 #define CONFIG_SYS_EEPROM_BUS_NUM		0
162 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
163 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
164 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
165 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
166 
167 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
168 
169 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
170 #define CONFIG_SYS_SCSI_MAX_LUN			1
171 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
172 						CONFIG_SYS_SCSI_MAX_LUN)
173 
174 /*
175  * IFC Definitions
176  */
177 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
178 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
179 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
180 				CSPR_PORT_SIZE_16 | \
181 				CSPR_MSEL_NOR | \
182 				CSPR_V)
183 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
184 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
185 				+ 0x8000000) | \
186 				CSPR_PORT_SIZE_16 | \
187 				CSPR_MSEL_NOR | \
188 				CSPR_V)
189 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
190 
191 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
192 					CSOR_NOR_TRHZ_80)
193 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
194 					FTIM0_NOR_TEADC(0x5) | \
195 					FTIM0_NOR_TEAHC(0x5))
196 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
197 					FTIM1_NOR_TRAD_NOR(0x1a) | \
198 					FTIM1_NOR_TSEQRAD_NOR(0x13))
199 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
200 					FTIM2_NOR_TCH(0x4) | \
201 					FTIM2_NOR_TWPH(0xe) | \
202 					FTIM2_NOR_TWP(0x1c))
203 #define CONFIG_SYS_NOR_FTIM3		0
204 
205 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
206 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
207 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
208 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
209 
210 #define CONFIG_SYS_FLASH_EMPTY_INFO
211 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
212 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
213 
214 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
215 #define CONFIG_SYS_WRITE_SWAPPED_DATA
216 
217 /*
218  * NAND Flash Definitions
219  */
220 #define CONFIG_NAND_FSL_IFC
221 
222 #define CONFIG_SYS_NAND_BASE		0x7e800000
223 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
224 
225 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
226 
227 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
228 				| CSPR_PORT_SIZE_8	\
229 				| CSPR_MSEL_NAND	\
230 				| CSPR_V)
231 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
232 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
233 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
234 				| CSOR_NAND_ECC_MODE_8	/* 8-bit ECC */ \
235 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
236 				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
237 				| CSOR_NAND_SPRZ_224	/* Spare size = 224 */ \
238 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
239 
240 #define CONFIG_SYS_NAND_ONFI_DETECTION
241 
242 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
243 					FTIM0_NAND_TWP(0x18)   | \
244 					FTIM0_NAND_TWCHT(0x7) | \
245 					FTIM0_NAND_TWH(0xa))
246 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
247 					FTIM1_NAND_TWBE(0x39)  | \
248 					FTIM1_NAND_TRR(0xe)   | \
249 					FTIM1_NAND_TRP(0x18))
250 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
251 					FTIM2_NAND_TREH(0xa) | \
252 					FTIM2_NAND_TWHRE(0x1e))
253 #define CONFIG_SYS_NAND_FTIM3           0x0
254 
255 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
256 #define CONFIG_SYS_MAX_NAND_DEVICE	1
257 #define CONFIG_MTD_NAND_VERIFY_WRITE
258 #define CONFIG_CMD_NAND
259 
260 #define CONFIG_SYS_NAND_BLOCK_SIZE	(256 * 1024)
261 #endif
262 
263 #ifdef CONFIG_NAND_BOOT
264 #define CONFIG_SPL_PAD_TO		0x40000		/* block aligned */
265 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
266 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
267 #endif
268 
269 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
270 #define CONFIG_QIXIS_I2C_ACCESS
271 #define CONFIG_SYS_I2C_EARLY_INIT
272 #endif
273 
274 /*
275  * QIXIS Definitions
276  */
277 #define CONFIG_FSL_QIXIS
278 
279 #ifdef CONFIG_FSL_QIXIS
280 #define QIXIS_BASE			0x7fb00000
281 #define QIXIS_BASE_PHYS			QIXIS_BASE
282 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
283 #define QIXIS_LBMAP_SWITCH		6
284 #define QIXIS_LBMAP_MASK		0x0f
285 #define QIXIS_LBMAP_SHIFT		0
286 #define QIXIS_LBMAP_DFLTBANK		0x00
287 #define QIXIS_LBMAP_ALTBANK		0x04
288 #define QIXIS_LBMAP_NAND		0x09
289 #define QIXIS_LBMAP_SD			0x00
290 #define QIXIS_LBMAP_SD_QSPI		0xff
291 #define QIXIS_LBMAP_QSPI		0xff
292 #define QIXIS_RCW_SRC_NAND		0x110
293 #define QIXIS_RCW_SRC_SD		0x040
294 #define QIXIS_RCW_SRC_QSPI		0x045
295 #define QIXIS_RST_CTL_RESET		0x41
296 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
297 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
298 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
299 
300 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
301 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
302 					CSPR_PORT_SIZE_8 | \
303 					CSPR_MSEL_GPCM | \
304 					CSPR_V)
305 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
306 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
307 					CSOR_NOR_NOR_MODE_AVD_NOR | \
308 					CSOR_NOR_TRHZ_80)
309 
310 /*
311  * QIXIS Timing parameters for IFC GPCM
312  */
313 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
314 					FTIM0_GPCM_TEADC(0x20) | \
315 					FTIM0_GPCM_TEAHC(0x10))
316 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
317 					FTIM1_GPCM_TRAD(0x1f))
318 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
319 					FTIM2_GPCM_TCH(0x8) | \
320 					FTIM2_GPCM_TWP(0xf0))
321 #define CONFIG_SYS_FPGA_FTIM3		0x0
322 #endif
323 
324 #ifdef CONFIG_NAND_BOOT
325 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
326 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
327 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
328 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
329 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
330 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
331 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
332 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
333 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
334 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
335 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
336 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
337 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
338 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
339 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
340 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
341 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
342 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
343 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
344 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
345 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
346 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
347 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
348 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
349 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
350 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
351 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
352 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
353 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
354 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
355 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
356 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
357 #else
358 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
359 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
360 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
361 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
362 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
363 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
364 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
365 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
366 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
367 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
368 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
369 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
370 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
371 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
372 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
373 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
374 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
375 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
376 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
377 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
378 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
379 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
380 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
381 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
382 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
383 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
384 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
385 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
386 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
387 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
388 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
389 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
390 #endif
391 
392 /*
393  * I2C bus multiplexer
394  */
395 #define I2C_MUX_PCA_ADDR_PRI		0x77
396 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
397 #define I2C_RETIMER_ADDR		0x18
398 #define I2C_MUX_CH_DEFAULT		0x8
399 #define I2C_MUX_CH_CH7301		0xC
400 #define I2C_MUX_CH5			0xD
401 #define I2C_MUX_CH6			0xE
402 #define I2C_MUX_CH7			0xF
403 
404 #define I2C_MUX_CH_VOL_MONITOR 0xa
405 
406 /* Voltage monitor on channel 2*/
407 #define I2C_VOL_MONITOR_ADDR           0x40
408 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
409 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
410 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
411 
412 #define CONFIG_VID_FLS_ENV		"ls1046aqds_vdd_mv"
413 #ifndef CONFIG_SPL_BUILD
414 #define CONFIG_VID
415 #endif
416 #define CONFIG_VOL_MONITOR_IR36021_SET
417 #define CONFIG_VOL_MONITOR_INA220
418 /* The lowest and highest voltage allowed for LS1046AQDS */
419 #define VDD_MV_MIN			819
420 #define VDD_MV_MAX			1212
421 
422 /*
423  * Miscellaneous configurable options
424  */
425 #define CONFIG_MISC_INIT_R
426 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
427 #define CONFIG_AUTO_COMPLETE
428 #define CONFIG_SYS_PBSIZE		\
429 		(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
430 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
431 
432 #define CONFIG_SYS_MEMTEST_START	0x80000000
433 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
434 
435 #define CONFIG_SYS_HZ			1000
436 
437 #define CONFIG_SYS_INIT_SP_OFFSET \
438 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
439 
440 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
441 
442 /*
443  * Environment
444  */
445 #define CONFIG_ENV_OVERWRITE
446 
447 #ifdef CONFIG_NAND_BOOT
448 #define CONFIG_ENV_IS_IN_NAND
449 #define CONFIG_ENV_SIZE			0x2000
450 #define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
451 #elif defined(CONFIG_SD_BOOT)
452 #define CONFIG_ENV_OFFSET		(1024 * 1024)
453 #define CONFIG_ENV_IS_IN_MMC
454 #define CONFIG_SYS_MMC_ENV_DEV		0
455 #define CONFIG_ENV_SIZE			0x2000
456 #elif defined(CONFIG_QSPI_BOOT)
457 #define CONFIG_ENV_IS_IN_SPI_FLASH
458 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
459 #define CONFIG_ENV_OFFSET		0x100000        /* 1MB */
460 #define CONFIG_ENV_SECT_SIZE		0x10000
461 #else
462 #define CONFIG_ENV_IS_IN_FLASH
463 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x200000)
464 #define CONFIG_ENV_SECT_SIZE		0x20000
465 #define CONFIG_ENV_SIZE			0x20000
466 #endif
467 
468 #define CONFIG_CMDLINE_TAG
469 
470 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
471 #define CONFIG_BOOTCOMMAND		"sf probe && sf read $kernel_load "    \
472 					"e0000 f00000 && bootm $kernel_load"
473 #else
474 #define CONFIG_BOOTCOMMAND		"cp.b $kernel_start $kernel_load "     \
475 					"$kernel_size && bootm $kernel_load"
476 #endif
477 
478 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
479 #define MTDPARTS_DEFAULT "mtdparts=1550000.quadspi:2m(uboot)," \
480 			"14m(free)"
481 #else
482 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \
483 			"2m@0x100000(nor_bank0_uboot),"\
484 			"40m@0x1100000(nor_bank0_fit)," \
485 			"7m(nor_bank0_user)," \
486 			"2m@0x4100000(nor_bank4_uboot)," \
487 			"40m@0x5100000(nor_bank4_fit),"\
488 			"-(nor_bank4_user);" \
489 			"7e800000.flash:" \
490 			"4m(nand_uboot),36m(nand_kernel)," \
491 			"472m(nand_free);spi0.0:2m(uboot)," \
492 			"14m(free)"
493 #endif
494 
495 #include <asm/fsl_secure_boot.h>
496 
497 #endif /* __LS1046AQDS_H__ */
498