1 /*
2  * Copyright 2016 Freescale Semiconductor
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1046A_COMMON_H
8 #define __LS1046A_COMMON_H
9 
10 /* SPL build */
11 #ifdef CONFIG_SPL_BUILD
12 #define SPL_NO_QBMAN
13 #define SPL_NO_FMAN
14 #define SPL_NO_ENV
15 #define SPL_NO_MISC
16 #define SPL_NO_QSPI
17 #define SPL_NO_USB
18 #define SPL_NO_SATA
19 #endif
20 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
21 #define SPL_NO_MMC
22 #endif
23 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT))
24 #define SPL_NO_IFC
25 #endif
26 
27 #define CONFIG_REMAKE_ELF
28 #define CONFIG_FSL_LAYERSCAPE
29 #define CONFIG_MP
30 #define CONFIG_GICV2
31 
32 #include <asm/arch/config.h>
33 #include <asm/arch/stream_id_lsch2.h>
34 
35 /* Link Definitions */
36 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
37 
38 #define CONFIG_SUPPORT_RAW_INITRD
39 
40 #define CONFIG_SKIP_LOWLEVEL_INIT
41 
42 #define CONFIG_VERY_BIG_RAM
43 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
44 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
45 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
46 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
47 
48 #define CPU_RELEASE_ADDR               secondary_boot_func
49 
50 /* Generic Timer Definitions */
51 #define COUNTER_FREQUENCY		25000000	/* 25MHz */
52 
53 /* Size of malloc() pool */
54 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)
55 
56 /* Serial Port */
57 #define CONFIG_CONS_INDEX		1
58 #define CONFIG_SYS_NS16550_SERIAL
59 #define CONFIG_SYS_NS16550_REG_SIZE	1
60 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
61 
62 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
63 
64 /* SD boot SPL */
65 #ifdef CONFIG_SD_BOOT
66 #define CONFIG_SPL_FRAMEWORK
67 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
68 #define CONFIG_SPL_LIBCOMMON_SUPPORT
69 #define CONFIG_SPL_LIBGENERIC_SUPPORT
70 #define CONFIG_SPL_ENV_SUPPORT
71 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
72 #define CONFIG_SPL_WATCHDOG_SUPPORT
73 #define CONFIG_SPL_I2C_SUPPORT
74 #define CONFIG_SPL_SERIAL_SUPPORT
75 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
76 
77 #define CONFIG_SPL_MMC_SUPPORT
78 #define CONFIG_SPL_TEXT_BASE		0x10000000
79 #define CONFIG_SPL_MAX_SIZE		0x1f000		/* 124 KiB */
80 #define CONFIG_SPL_STACK		0x10020000
81 #define CONFIG_SPL_PAD_TO		0x21000		/* 132 KiB */
82 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
83 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
84 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
85 					CONFIG_SPL_BSS_MAX_SIZE)
86 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
87 
88 #ifdef CONFIG_SECURE_BOOT
89 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
90 /*
91  * HDR would be appended at end of image and copied to DDR along
92  * with U-Boot image. Here u-boot max. size is 512K. So if binary
93  * size increases then increase this size in case of secure boot as
94  * it uses raw u-boot image instead of fit image.
95  */
96 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
97 #else
98 #define CONFIG_SYS_MONITOR_LEN		0x100000
99 #endif /* ifdef CONFIG_SECURE_BOOT */
100 #endif
101 
102 /* NAND SPL */
103 #ifdef CONFIG_NAND_BOOT
104 #define CONFIG_SPL_PBL_PAD
105 #define CONFIG_SPL_FRAMEWORK
106 #define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
107 #define CONFIG_SPL_LIBCOMMON_SUPPORT
108 #define CONFIG_SPL_LIBGENERIC_SUPPORT
109 #define CONFIG_SPL_ENV_SUPPORT
110 #define CONFIG_SPL_WATCHDOG_SUPPORT
111 #define CONFIG_SPL_I2C_SUPPORT
112 #define CONFIG_SPL_SERIAL_SUPPORT
113 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
114 
115 #define CONFIG_SPL_NAND_SUPPORT
116 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
117 #define CONFIG_SPL_TEXT_BASE		0x10000000
118 #define CONFIG_SPL_MAX_SIZE		0x17000		/* 90 KiB */
119 #define CONFIG_SPL_STACK		0x1001f000
120 #define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
121 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
122 
123 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
124 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
125 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
126 					CONFIG_SPL_BSS_MAX_SIZE)
127 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
128 #define CONFIG_SYS_MONITOR_LEN		0xa0000
129 #endif
130 
131 /* I2C */
132 #define CONFIG_SYS_I2C
133 #define CONFIG_SYS_I2C_MXC
134 #define CONFIG_SYS_I2C_MXC_I2C1
135 #define CONFIG_SYS_I2C_MXC_I2C2
136 #define CONFIG_SYS_I2C_MXC_I2C3
137 #define CONFIG_SYS_I2C_MXC_I2C4
138 
139 /* PCIe */
140 #define CONFIG_PCIE1		/* PCIE controller 1 */
141 #define CONFIG_PCIE2		/* PCIE controller 2 */
142 #define CONFIG_PCIE3		/* PCIE controller 3 */
143 
144 #ifdef CONFIG_PCI
145 #define CONFIG_PCI_SCAN_SHOW
146 #endif
147 
148 /* Command line configuration */
149 
150 /* MMC */
151 #ifndef SPL_NO_MMC
152 #ifdef CONFIG_MMC
153 #define CONFIG_FSL_ESDHC
154 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
155 #endif
156 #endif
157 
158 #ifndef SPL_NO_QBMAN
159 #define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
160 #endif
161 
162 /* FMan ucode */
163 #ifndef SPL_NO_FMAN
164 #define CONFIG_SYS_DPAA_FMAN
165 #ifdef CONFIG_SYS_DPAA_FMAN
166 #define CONFIG_SYS_FM_MURAM_SIZE	0x60000
167 #endif
168 
169 #ifdef CONFIG_SD_BOOT
170 /*
171  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
172  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
173  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
174  */
175 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
176 #define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
177 #elif defined(CONFIG_QSPI_BOOT)
178 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
179 #define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
180 #define CONFIG_ENV_SPI_BUS		0
181 #define CONFIG_ENV_SPI_CS		0
182 #define CONFIG_ENV_SPI_MAX_HZ		1000000
183 #define CONFIG_ENV_SPI_MODE		0x03
184 #elif defined(CONFIG_NAND_BOOT)
185 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
186 #define CONFIG_SYS_FMAN_FW_ADDR		(36 * CONFIG_SYS_NAND_BLOCK_SIZE)
187 #else
188 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
189 #define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
190 #endif
191 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
192 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
193 #endif
194 
195 /* Miscellaneous configurable options */
196 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
197 
198 #define CONFIG_HWCONFIG
199 #define HWCONFIG_BUFFER_SIZE		128
200 
201 #include <config_distro_defaults.h>
202 #ifndef CONFIG_SPL_BUILD
203 #define BOOT_TARGET_DEVICES(func) \
204 	func(MMC, mmc, 0) \
205 	func(USB, usb, 0)
206 #include <config_distro_bootcmd.h>
207 #endif
208 
209 #ifndef SPL_NO_MISC
210 /* Initial environment variables */
211 #define CONFIG_EXTRA_ENV_SETTINGS		\
212 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
213 	"ramdisk_addr=0x800000\0"		\
214 	"ramdisk_size=0x2000000\0"		\
215 	"fdt_high=0xffffffffffffffff\0"		\
216 	"initrd_high=0xffffffffffffffff\0"	\
217 	"fdt_addr=0x64f00000\0"                 \
218 	"kernel_addr=0x65000000\0"              \
219 	"scriptaddr=0x80000000\0"               \
220 	"scripthdraddr=0x80080000\0"		\
221 	"fdtheader_addr_r=0x80100000\0"         \
222 	"kernelheader_addr_r=0x80200000\0"      \
223 	"load_addr=0xa0000000\0"            \
224 	"kernel_addr_r=0x81000000\0"            \
225 	"fdt_addr_r=0x90000000\0"               \
226 	"ramdisk_addr_r=0xa0000000\0"           \
227 	"kernel_start=0x1000000\0"		\
228 	"kernel_load=0xa0000000\0"		\
229 	"kernel_size=0x2800000\0"		\
230 	"kernel_addr_sd=0x8000\0"		\
231 	"kernel_size_sd=0x14000\0"		\
232 	"console=ttyS0,115200\0"                \
233 	 CONFIG_MTDPARTS_DEFAULT "\0"		\
234 	BOOTENV					\
235 	"boot_scripts=ls1046ardb_boot.scr\0"    \
236 	"boot_script_hdr=hdr_ls1046ardb_bs.out\0"	\
237 	"scan_dev_for_boot_part="               \
238 		"part list ${devtype} ${devnum} devplist; "   \
239 		"env exists devplist || setenv devplist 1; "  \
240 		"for distro_bootpart in ${devplist}; do "     \
241 		  "if fstype ${devtype} "                  \
242 			"${devnum}:${distro_bootpart} "      \
243 			"bootfstype; then "                  \
244 			"run scan_dev_for_boot; "            \
245 		  "fi; "                                   \
246 		"done\0"                                   \
247 	"scan_dev_for_boot="				  \
248 		"echo Scanning ${devtype} "		  \
249 				"${devnum}:${distro_bootpart}...; "  \
250 		"for prefix in ${boot_prefixes}; do "	  \
251 			"run scan_dev_for_scripts; "	  \
252 		"done;"					  \
253 		"\0"					  \
254 	"boot_a_script="				  \
255 		"load ${devtype} ${devnum}:${distro_bootpart} "  \
256 			"${scriptaddr} ${prefix}${script}; "    \
257 		"env exists secureboot && load ${devtype} "     \
258 			"${devnum}:${distro_bootpart} "		\
259 			"${scripthdraddr} ${prefix}${boot_script_hdr} " \
260 			"&& esbc_validate ${scripthdraddr};"    \
261 		"source ${scriptaddr}\0"	  \
262 	"qspi_bootcmd=echo Trying load from qspi..;"      \
263 		"sf probe && sf read $load_addr "         \
264 		"$kernel_start $kernel_size && bootm $load_addr#$board\0" \
265 	"sd_bootcmd=echo Trying load from SD ..;"	\
266 		"mmcinfo; mmc read $load_addr "		\
267 		"$kernel_addr_sd $kernel_size_sd && "	\
268 		"bootm $load_addr#$board\0"
269 
270 #endif
271 
272 /* Monitor Command Prompt */
273 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
274 #define CONFIG_SYS_LONGHELP
275 
276 #define CONFIG_AUTO_COMPLETE
277 #define CONFIG_SYS_MAXARGS		64	/* max command args */
278 
279 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
280 
281 #include <asm/arch/soc.h>
282 
283 #endif /* __LS1046A_COMMON_H */
284