xref: /openbmc/u-boot/include/configs/ls1043aqds.h (revision e12546de)
1 /*
2  * Copyright 2015 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0+
5  */
6 
7 #ifndef __LS1043AQDS_H__
8 #define __LS1043AQDS_H__
9 
10 #include "ls1043a_common.h"
11 
12 #ifndef __ASSEMBLY__
13 unsigned long get_board_sys_clk(void);
14 unsigned long get_board_ddr_clk(void);
15 #endif
16 
17 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
18 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
19 
20 #define CONFIG_SKIP_LOWLEVEL_INIT
21 
22 #define CONFIG_LAYERSCAPE_NS_ACCESS
23 
24 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
25 /* Physical Memory Map */
26 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
27 #define CONFIG_NR_DRAM_BANKS		2
28 
29 #define CONFIG_DDR_SPD
30 #define SPD_EEPROM_ADDRESS		0x51
31 #define CONFIG_SYS_SPD_BUS_NUM		0
32 
33 #ifndef CONFIG_SPL
34 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
35 #endif
36 
37 #define CONFIG_DDR_ECC
38 #ifdef CONFIG_DDR_ECC
39 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
40 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
41 #endif
42 
43 #ifdef CONFIG_SYS_DPAA_FMAN
44 #define CONFIG_FMAN_ENET
45 #define CONFIG_PHY_VITESSE
46 #define CONFIG_PHY_REALTEK
47 #define CONFIG_PHYLIB_10G
48 #define RGMII_PHY1_ADDR		0x1
49 #define RGMII_PHY2_ADDR		0x2
50 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
51 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
52 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
53 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
54 /* PHY address on QSGMII riser card on slot 1 */
55 #define QSGMII_CARD_PORT1_PHY_ADDR_S1 0x4
56 #define QSGMII_CARD_PORT2_PHY_ADDR_S1 0x5
57 #define QSGMII_CARD_PORT3_PHY_ADDR_S1 0x6
58 #define QSGMII_CARD_PORT4_PHY_ADDR_S1 0x7
59 /* PHY address on QSGMII riser card on slot 2 */
60 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
61 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
62 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
63 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
64 #endif
65 
66 #ifdef CONFIG_RAMBOOT_PBL
67 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043aqds/ls1043aqds_pbi.cfg
68 #endif
69 
70 #ifdef CONFIG_NAND_BOOT
71 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg
72 #endif
73 
74 #ifdef CONFIG_SD_BOOT
75 #ifdef CONFIG_SD_BOOT_QSPI
76 #define CONFIG_SYS_FSL_PBL_RCW \
77 	board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg
78 #else
79 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg
80 #endif
81 #endif
82 
83 /* LPUART */
84 #ifdef CONFIG_LPUART
85 #define CONFIG_LPUART_32B_REG
86 #endif
87 
88 /* SATA */
89 #define CONFIG_SCSI_AHCI_PLAT
90 
91 /* EEPROM */
92 #define CONFIG_ID_EEPROM
93 #define CONFIG_SYS_I2C_EEPROM_NXID
94 #define CONFIG_SYS_EEPROM_BUS_NUM		0
95 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
96 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
97 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
98 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
99 
100 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
101 
102 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
103 #define CONFIG_SYS_SCSI_MAX_LUN			1
104 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
105 						CONFIG_SYS_SCSI_MAX_LUN)
106 
107 /*
108  * IFC Definitions
109  */
110 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
111 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
112 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
113 				CSPR_PORT_SIZE_16 | \
114 				CSPR_MSEL_NOR | \
115 				CSPR_V)
116 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
117 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
118 				+ 0x8000000) | \
119 				CSPR_PORT_SIZE_16 | \
120 				CSPR_MSEL_NOR | \
121 				CSPR_V)
122 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
123 
124 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
125 					CSOR_NOR_TRHZ_80)
126 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
127 					FTIM0_NOR_TEADC(0x5) | \
128 					FTIM0_NOR_TEAHC(0x5))
129 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
130 					FTIM1_NOR_TRAD_NOR(0x1a) | \
131 					FTIM1_NOR_TSEQRAD_NOR(0x13))
132 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
133 					FTIM2_NOR_TCH(0x4) | \
134 					FTIM2_NOR_TWPH(0xe) | \
135 					FTIM2_NOR_TWP(0x1c))
136 #define CONFIG_SYS_NOR_FTIM3		0
137 
138 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
139 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
140 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
141 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
142 
143 #define CONFIG_SYS_FLASH_EMPTY_INFO
144 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
145 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
146 
147 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
148 #define CONFIG_SYS_WRITE_SWAPPED_DATA
149 
150 /*
151  * NAND Flash Definitions
152  */
153 #define CONFIG_NAND_FSL_IFC
154 
155 #define CONFIG_SYS_NAND_BASE		0x7e800000
156 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
157 
158 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
159 
160 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
161 				| CSPR_PORT_SIZE_8	\
162 				| CSPR_MSEL_NAND	\
163 				| CSPR_V)
164 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
165 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
166 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
167 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
168 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
169 				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
170 				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */ \
171 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
172 
173 #define CONFIG_SYS_NAND_ONFI_DETECTION
174 
175 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
176 					FTIM0_NAND_TWP(0x18)   | \
177 					FTIM0_NAND_TWCHT(0x7) | \
178 					FTIM0_NAND_TWH(0xa))
179 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
180 					FTIM1_NAND_TWBE(0x39)  | \
181 					FTIM1_NAND_TRR(0xe)   | \
182 					FTIM1_NAND_TRP(0x18))
183 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
184 					FTIM2_NAND_TREH(0xa) | \
185 					FTIM2_NAND_TWHRE(0x1e))
186 #define CONFIG_SYS_NAND_FTIM3           0x0
187 
188 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
189 #define CONFIG_SYS_MAX_NAND_DEVICE	1
190 #define CONFIG_MTD_NAND_VERIFY_WRITE
191 
192 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
193 #endif
194 
195 #ifdef CONFIG_NAND_BOOT
196 #define CONFIG_SPL_PAD_TO		0x20000		/* block aligned */
197 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
198 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(640 << 10)
199 #endif
200 
201 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
202 #define CONFIG_QIXIS_I2C_ACCESS
203 #define CONFIG_SYS_I2C_EARLY_INIT
204 #endif
205 
206 /*
207  * QIXIS Definitions
208  */
209 #define CONFIG_FSL_QIXIS
210 
211 #ifdef CONFIG_FSL_QIXIS
212 #define QIXIS_BASE			0x7fb00000
213 #define QIXIS_BASE_PHYS			QIXIS_BASE
214 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
215 #define QIXIS_LBMAP_SWITCH		6
216 #define QIXIS_LBMAP_MASK		0x0f
217 #define QIXIS_LBMAP_SHIFT		0
218 #define QIXIS_LBMAP_DFLTBANK		0x00
219 #define QIXIS_LBMAP_ALTBANK		0x04
220 #define QIXIS_LBMAP_NAND		0x09
221 #define QIXIS_LBMAP_SD			0x00
222 #define QIXIS_LBMAP_SD_QSPI		0xff
223 #define QIXIS_LBMAP_QSPI		0xff
224 #define QIXIS_RCW_SRC_NAND		0x106
225 #define QIXIS_RCW_SRC_SD		0x040
226 #define QIXIS_RCW_SRC_QSPI		0x045
227 #define QIXIS_RST_CTL_RESET		0x41
228 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
229 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
230 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
231 
232 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
233 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
234 					CSPR_PORT_SIZE_8 | \
235 					CSPR_MSEL_GPCM | \
236 					CSPR_V)
237 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
238 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
239 					CSOR_NOR_NOR_MODE_AVD_NOR | \
240 					CSOR_NOR_TRHZ_80)
241 
242 /*
243  * QIXIS Timing parameters for IFC GPCM
244  */
245 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
246 					FTIM0_GPCM_TEADC(0x20) | \
247 					FTIM0_GPCM_TEAHC(0x10))
248 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
249 					FTIM1_GPCM_TRAD(0x1f))
250 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
251 					FTIM2_GPCM_TCH(0x8) | \
252 					FTIM2_GPCM_TWP(0xf0))
253 #define CONFIG_SYS_FPGA_FTIM3		0x0
254 #endif
255 
256 #ifdef CONFIG_NAND_BOOT
257 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
258 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
259 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
260 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
261 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
262 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
263 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
264 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
265 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
266 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
267 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
268 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
269 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
270 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
271 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
272 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
273 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
274 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
275 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
276 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
277 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
278 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
279 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
280 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
281 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
282 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
283 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
284 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
285 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
286 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
287 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
288 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
289 #else
290 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
291 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
292 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
293 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
294 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
295 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
296 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
297 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
298 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
299 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
300 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
301 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
302 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
303 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
304 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
305 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
306 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
307 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
308 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
309 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
310 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
311 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
312 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
313 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
314 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
315 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
316 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
317 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
318 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
319 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
320 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
321 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
322 #endif
323 
324 /*
325  * I2C bus multiplexer
326  */
327 #define I2C_MUX_PCA_ADDR_PRI		0x77
328 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
329 #define I2C_RETIMER_ADDR		0x18
330 #define I2C_MUX_CH_DEFAULT		0x8
331 #define I2C_MUX_CH_CH7301		0xC
332 #define I2C_MUX_CH5			0xD
333 #define I2C_MUX_CH7			0xF
334 
335 #define I2C_MUX_CH_VOL_MONITOR 0xa
336 
337 /* Voltage monitor on channel 2*/
338 #define I2C_VOL_MONITOR_ADDR           0x40
339 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
340 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
341 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
342 
343 #define CONFIG_VID_FLS_ENV		"ls1043aqds_vdd_mv"
344 #ifndef CONFIG_SPL_BUILD
345 #define CONFIG_VID
346 #endif
347 #define CONFIG_VOL_MONITOR_IR36021_SET
348 #define CONFIG_VOL_MONITOR_INA220
349 /* The lowest and highest voltage allowed for LS1043AQDS */
350 #define VDD_MV_MIN			819
351 #define VDD_MV_MAX			1212
352 
353 /* QSPI device */
354 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
355 #define CONFIG_FSL_QSPI
356 #ifdef CONFIG_FSL_QSPI
357 #define CONFIG_SPI_FLASH_SPANSION
358 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
359 #define FSL_QSPI_FLASH_NUM		2
360 #endif
361 #endif
362 
363 /*
364  * Miscellaneous configurable options
365  */
366 #define CONFIG_MISC_INIT_R
367 
368 #define CONFIG_SYS_MEMTEST_START	0x80000000
369 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
370 
371 #define CONFIG_SYS_HZ			1000
372 
373 #define CONFIG_SYS_INIT_SP_OFFSET \
374 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
375 
376 #ifdef CONFIG_SPL_BUILD
377 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
378 #else
379 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
380 #endif
381 
382 /*
383  * Environment
384  */
385 #define CONFIG_ENV_OVERWRITE
386 
387 #ifdef CONFIG_NAND_BOOT
388 #define CONFIG_ENV_SIZE			0x2000
389 #define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
390 #elif defined(CONFIG_SD_BOOT)
391 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
392 #define CONFIG_SYS_MMC_ENV_DEV		0
393 #define CONFIG_ENV_SIZE			0x2000
394 #elif defined(CONFIG_QSPI_BOOT)
395 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
396 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
397 #define CONFIG_ENV_SECT_SIZE		0x10000
398 #else
399 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
400 #define CONFIG_ENV_SECT_SIZE		0x20000
401 #define CONFIG_ENV_SIZE			0x20000
402 #endif
403 
404 #define CONFIG_CMDLINE_TAG
405 
406 #include <asm/fsl_secure_boot.h>
407 
408 #endif /* __LS1043AQDS_H__ */
409