xref: /openbmc/u-boot/include/configs/ls1043aqds.h (revision 8ee59472)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2015 Freescale Semiconductor, Inc.
4  */
5 
6 #ifndef __LS1043AQDS_H__
7 #define __LS1043AQDS_H__
8 
9 #include "ls1043a_common.h"
10 
11 #ifndef __ASSEMBLY__
12 unsigned long get_board_sys_clk(void);
13 unsigned long get_board_ddr_clk(void);
14 #endif
15 
16 #define CONFIG_SYS_CLK_FREQ		get_board_sys_clk()
17 #define CONFIG_DDR_CLK_FREQ		get_board_ddr_clk()
18 
19 #define CONFIG_SKIP_LOWLEVEL_INIT
20 
21 #define CONFIG_LAYERSCAPE_NS_ACCESS
22 
23 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
24 /* Physical Memory Map */
25 #define CONFIG_CHIP_SELECTS_PER_CTRL	4
26 #define CONFIG_NR_DRAM_BANKS		2
27 
28 #define CONFIG_DDR_SPD
29 #define SPD_EEPROM_ADDRESS		0x51
30 #define CONFIG_SYS_SPD_BUS_NUM		0
31 
32 #ifndef CONFIG_SPL
33 #define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
34 #endif
35 
36 #define CONFIG_DDR_ECC
37 #ifdef CONFIG_DDR_ECC
38 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
39 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
40 #endif
41 
42 #ifdef CONFIG_SYS_DPAA_FMAN
43 #define CONFIG_FMAN_ENET
44 #define CONFIG_PHY_VITESSE
45 #define CONFIG_PHY_REALTEK
46 #define CONFIG_PHYLIB_10G
47 #define RGMII_PHY1_ADDR		0x1
48 #define RGMII_PHY2_ADDR		0x2
49 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
50 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
51 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
52 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
53 /* PHY address on QSGMII riser card on slot 1 */
54 #define QSGMII_CARD_PORT1_PHY_ADDR_S1 0x4
55 #define QSGMII_CARD_PORT2_PHY_ADDR_S1 0x5
56 #define QSGMII_CARD_PORT3_PHY_ADDR_S1 0x6
57 #define QSGMII_CARD_PORT4_PHY_ADDR_S1 0x7
58 /* PHY address on QSGMII riser card on slot 2 */
59 #define QSGMII_CARD_PORT1_PHY_ADDR_S2 0x8
60 #define QSGMII_CARD_PORT2_PHY_ADDR_S2 0x9
61 #define QSGMII_CARD_PORT3_PHY_ADDR_S2 0xA
62 #define QSGMII_CARD_PORT4_PHY_ADDR_S2 0xB
63 #endif
64 
65 #ifdef CONFIG_RAMBOOT_PBL
66 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1043aqds/ls1043aqds_pbi.cfg
67 #endif
68 
69 #ifdef CONFIG_NAND_BOOT
70 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg
71 #endif
72 
73 #ifdef CONFIG_SD_BOOT
74 #ifdef CONFIG_SD_BOOT_QSPI
75 #define CONFIG_SYS_FSL_PBL_RCW \
76 	board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg
77 #else
78 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg
79 #endif
80 #endif
81 
82 /* LPUART */
83 #ifdef CONFIG_LPUART
84 #define CONFIG_LPUART_32B_REG
85 #endif
86 
87 /* SATA */
88 #define CONFIG_SCSI_AHCI_PLAT
89 
90 /* EEPROM */
91 #define CONFIG_ID_EEPROM
92 #define CONFIG_SYS_I2C_EEPROM_NXID
93 #define CONFIG_SYS_EEPROM_BUS_NUM		0
94 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x57
95 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
96 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
97 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	5
98 
99 #define CONFIG_SYS_SATA				AHCI_BASE_ADDR
100 
101 #define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
102 #define CONFIG_SYS_SCSI_MAX_LUN			1
103 #define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
104 						CONFIG_SYS_SCSI_MAX_LUN)
105 
106 /*
107  * IFC Definitions
108  */
109 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
110 #define CONFIG_SYS_NOR0_CSPR_EXT	(0x0)
111 #define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
112 				CSPR_PORT_SIZE_16 | \
113 				CSPR_MSEL_NOR | \
114 				CSPR_V)
115 #define CONFIG_SYS_NOR1_CSPR_EXT	(0x0)
116 #define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
117 				+ 0x8000000) | \
118 				CSPR_PORT_SIZE_16 | \
119 				CSPR_MSEL_NOR | \
120 				CSPR_V)
121 #define CONFIG_SYS_NOR_AMASK		IFC_AMASK(128 * 1024 * 1024)
122 
123 #define CONFIG_SYS_NOR_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
124 					CSOR_NOR_TRHZ_80)
125 #define CONFIG_SYS_NOR_FTIM0		(FTIM0_NOR_TACSE(0x4) | \
126 					FTIM0_NOR_TEADC(0x5) | \
127 					FTIM0_NOR_TEAHC(0x5))
128 #define CONFIG_SYS_NOR_FTIM1		(FTIM1_NOR_TACO(0x35) | \
129 					FTIM1_NOR_TRAD_NOR(0x1a) | \
130 					FTIM1_NOR_TSEQRAD_NOR(0x13))
131 #define CONFIG_SYS_NOR_FTIM2		(FTIM2_NOR_TCS(0x4) | \
132 					FTIM2_NOR_TCH(0x4) | \
133 					FTIM2_NOR_TWPH(0xe) | \
134 					FTIM2_NOR_TWP(0x1c))
135 #define CONFIG_SYS_NOR_FTIM3		0
136 
137 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
138 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
139 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
140 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
141 
142 #define CONFIG_SYS_FLASH_EMPTY_INFO
143 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS, \
144 					CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
145 
146 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
147 #define CONFIG_SYS_WRITE_SWAPPED_DATA
148 
149 /*
150  * NAND Flash Definitions
151  */
152 #define CONFIG_NAND_FSL_IFC
153 
154 #define CONFIG_SYS_NAND_BASE		0x7e800000
155 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
156 
157 #define CONFIG_SYS_NAND_CSPR_EXT	(0x0)
158 
159 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
160 				| CSPR_PORT_SIZE_8	\
161 				| CSPR_MSEL_NAND	\
162 				| CSPR_V)
163 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
164 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
165 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
166 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
167 				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
168 				| CSOR_NAND_PGS_2K	/* Page Size = 2K */ \
169 				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */ \
170 				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
171 
172 #define CONFIG_SYS_NAND_ONFI_DETECTION
173 
174 #define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x7) | \
175 					FTIM0_NAND_TWP(0x18)   | \
176 					FTIM0_NAND_TWCHT(0x7) | \
177 					FTIM0_NAND_TWH(0xa))
178 #define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
179 					FTIM1_NAND_TWBE(0x39)  | \
180 					FTIM1_NAND_TRR(0xe)   | \
181 					FTIM1_NAND_TRP(0x18))
182 #define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0xf) | \
183 					FTIM2_NAND_TREH(0xa) | \
184 					FTIM2_NAND_TWHRE(0x1e))
185 #define CONFIG_SYS_NAND_FTIM3           0x0
186 
187 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
188 #define CONFIG_SYS_MAX_NAND_DEVICE	1
189 #define CONFIG_MTD_NAND_VERIFY_WRITE
190 
191 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
192 #endif
193 
194 #ifdef CONFIG_NAND_BOOT
195 #define CONFIG_SPL_PAD_TO		0x20000		/* block aligned */
196 #define CONFIG_SYS_NAND_U_BOOT_OFFS	CONFIG_SPL_PAD_TO
197 #define CONFIG_SYS_NAND_U_BOOT_SIZE	(640 << 10)
198 #endif
199 
200 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
201 #define CONFIG_QIXIS_I2C_ACCESS
202 #define CONFIG_SYS_I2C_EARLY_INIT
203 #endif
204 
205 /*
206  * QIXIS Definitions
207  */
208 #define CONFIG_FSL_QIXIS
209 
210 #ifdef CONFIG_FSL_QIXIS
211 #define QIXIS_BASE			0x7fb00000
212 #define QIXIS_BASE_PHYS			QIXIS_BASE
213 #define CONFIG_SYS_I2C_FPGA_ADDR	0x66
214 #define QIXIS_LBMAP_SWITCH		6
215 #define QIXIS_LBMAP_MASK		0x0f
216 #define QIXIS_LBMAP_SHIFT		0
217 #define QIXIS_LBMAP_DFLTBANK		0x00
218 #define QIXIS_LBMAP_ALTBANK		0x04
219 #define QIXIS_LBMAP_NAND		0x09
220 #define QIXIS_LBMAP_SD			0x00
221 #define QIXIS_LBMAP_SD_QSPI		0xff
222 #define QIXIS_LBMAP_QSPI		0xff
223 #define QIXIS_RCW_SRC_NAND		0x106
224 #define QIXIS_RCW_SRC_SD		0x040
225 #define QIXIS_RCW_SRC_QSPI		0x045
226 #define QIXIS_RST_CTL_RESET		0x41
227 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
228 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
229 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
230 
231 #define CONFIG_SYS_FPGA_CSPR_EXT	(0x0)
232 #define CONFIG_SYS_FPGA_CSPR		(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) | \
233 					CSPR_PORT_SIZE_8 | \
234 					CSPR_MSEL_GPCM | \
235 					CSPR_V)
236 #define CONFIG_SYS_FPGA_AMASK		IFC_AMASK(64 * 1024)
237 #define CONFIG_SYS_FPGA_CSOR		(CSOR_NOR_ADM_SHIFT(4) | \
238 					CSOR_NOR_NOR_MODE_AVD_NOR | \
239 					CSOR_NOR_TRHZ_80)
240 
241 /*
242  * QIXIS Timing parameters for IFC GPCM
243  */
244 #define CONFIG_SYS_FPGA_FTIM0		(FTIM0_GPCM_TACSE(0xc) | \
245 					FTIM0_GPCM_TEADC(0x20) | \
246 					FTIM0_GPCM_TEAHC(0x10))
247 #define CONFIG_SYS_FPGA_FTIM1		(FTIM1_GPCM_TACO(0x50) | \
248 					FTIM1_GPCM_TRAD(0x1f))
249 #define CONFIG_SYS_FPGA_FTIM2		(FTIM2_GPCM_TCS(0x8) | \
250 					FTIM2_GPCM_TCH(0x8) | \
251 					FTIM2_GPCM_TWP(0xf0))
252 #define CONFIG_SYS_FPGA_FTIM3		0x0
253 #endif
254 
255 #ifdef CONFIG_NAND_BOOT
256 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
257 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
258 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
259 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
260 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
261 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
262 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
263 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
264 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
265 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
266 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
267 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
268 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
269 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
270 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
271 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
272 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
273 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
274 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
275 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
276 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
277 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
278 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
279 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
280 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
281 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
282 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
283 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
284 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
285 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
286 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
287 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
288 #else
289 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
290 #define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
291 #define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
292 #define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
293 #define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
294 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
295 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
296 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
297 #define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
298 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
299 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
300 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
301 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
302 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
303 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
304 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
305 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
306 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
307 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
308 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
309 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
310 #define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
311 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
312 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
313 #define CONFIG_SYS_CSPR3_EXT		CONFIG_SYS_FPGA_CSPR_EXT
314 #define CONFIG_SYS_CSPR3		CONFIG_SYS_FPGA_CSPR
315 #define CONFIG_SYS_AMASK3		CONFIG_SYS_FPGA_AMASK
316 #define CONFIG_SYS_CSOR3		CONFIG_SYS_FPGA_CSOR
317 #define CONFIG_SYS_CS3_FTIM0		CONFIG_SYS_FPGA_FTIM0
318 #define CONFIG_SYS_CS3_FTIM1		CONFIG_SYS_FPGA_FTIM1
319 #define CONFIG_SYS_CS3_FTIM2		CONFIG_SYS_FPGA_FTIM2
320 #define CONFIG_SYS_CS3_FTIM3		CONFIG_SYS_FPGA_FTIM3
321 #endif
322 
323 /*
324  * I2C bus multiplexer
325  */
326 #define I2C_MUX_PCA_ADDR_PRI		0x77
327 #define I2C_MUX_PCA_ADDR_SEC		0x76 /* Secondary multiplexer */
328 #define I2C_RETIMER_ADDR		0x18
329 #define I2C_MUX_CH_DEFAULT		0x8
330 #define I2C_MUX_CH_CH7301		0xC
331 #define I2C_MUX_CH5			0xD
332 #define I2C_MUX_CH7			0xF
333 
334 #define I2C_MUX_CH_VOL_MONITOR 0xa
335 
336 /* Voltage monitor on channel 2*/
337 #define I2C_VOL_MONITOR_ADDR           0x40
338 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
339 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
340 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
341 
342 #define CONFIG_VID_FLS_ENV		"ls1043aqds_vdd_mv"
343 #ifndef CONFIG_SPL_BUILD
344 #define CONFIG_VID
345 #endif
346 #define CONFIG_VOL_MONITOR_IR36021_SET
347 #define CONFIG_VOL_MONITOR_INA220
348 /* The lowest and highest voltage allowed for LS1043AQDS */
349 #define VDD_MV_MIN			819
350 #define VDD_MV_MAX			1212
351 
352 /* QSPI device */
353 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
354 #define CONFIG_FSL_QSPI
355 #ifdef CONFIG_FSL_QSPI
356 #define CONFIG_SPI_FLASH_SPANSION
357 #define FSL_QSPI_FLASH_SIZE		(1 << 24)
358 #define FSL_QSPI_FLASH_NUM		2
359 #endif
360 #endif
361 
362 /*
363  * Miscellaneous configurable options
364  */
365 #define CONFIG_MISC_INIT_R
366 
367 #define CONFIG_SYS_MEMTEST_START	0x80000000
368 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
369 
370 #define CONFIG_SYS_HZ			1000
371 
372 #define CONFIG_SYS_INIT_SP_OFFSET \
373 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
374 
375 #ifdef CONFIG_SPL_BUILD
376 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
377 #else
378 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
379 #endif
380 
381 /*
382  * Environment
383  */
384 #define CONFIG_ENV_OVERWRITE
385 
386 #ifdef CONFIG_NAND_BOOT
387 #define CONFIG_ENV_SIZE			0x2000
388 #define CONFIG_ENV_OFFSET		(24 * CONFIG_SYS_NAND_BLOCK_SIZE)
389 #elif defined(CONFIG_SD_BOOT)
390 #define CONFIG_ENV_OFFSET		(3 * 1024 * 1024)
391 #define CONFIG_SYS_MMC_ENV_DEV		0
392 #define CONFIG_ENV_SIZE			0x2000
393 #elif defined(CONFIG_QSPI_BOOT)
394 #define CONFIG_ENV_SIZE			0x2000          /* 8KB */
395 #define CONFIG_ENV_OFFSET		0x300000        /* 3MB */
396 #define CONFIG_ENV_SECT_SIZE		0x10000
397 #else
398 #define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + 0x300000)
399 #define CONFIG_ENV_SECT_SIZE		0x20000
400 #define CONFIG_ENV_SIZE			0x20000
401 #endif
402 
403 #define CONFIG_CMDLINE_TAG
404 
405 #include <asm/fsl_secure_boot.h>
406 
407 #endif /* __LS1043AQDS_H__ */
408