1 /* 2 * Copyright (C) 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS1043A_COMMON_H 8 #define __LS1043A_COMMON_H 9 10 #define CONFIG_REMAKE_ELF 11 #define CONFIG_FSL_LAYERSCAPE 12 #define CONFIG_LS1043A 13 #define CONFIG_MP 14 #define CONFIG_SYS_FSL_CLK 15 #define CONFIG_GICV2 16 17 #include <asm/arch/config.h> 18 19 /* Link Definitions */ 20 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 21 22 #define CONFIG_SUPPORT_RAW_INITRD 23 24 #define CONFIG_SKIP_LOWLEVEL_INIT 25 #define CONFIG_BOARD_EARLY_INIT_F 1 26 27 #define CONFIG_VERY_BIG_RAM 28 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 29 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 30 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 31 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL 32 33 #define CPU_RELEASE_ADDR secondary_boot_func 34 35 /* Generic Timer Definitions */ 36 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 37 38 /* Size of malloc() pool */ 39 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) 40 41 /* Serial Port */ 42 #define CONFIG_CONS_INDEX 1 43 #define CONFIG_SYS_NS16550_SERIAL 44 #define CONFIG_SYS_NS16550_REG_SIZE 1 45 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) 46 47 #define CONFIG_BAUDRATE 115200 48 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 49 50 /* SD boot SPL */ 51 #ifdef CONFIG_SD_BOOT 52 #define CONFIG_SPL_FRAMEWORK 53 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" 54 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 55 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xf0 56 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x500 57 58 #define CONFIG_SPL_TEXT_BASE 0x10000000 59 #define CONFIG_SPL_MAX_SIZE 0x1d000 60 #define CONFIG_SPL_STACK 0x1001e000 61 #define CONFIG_SPL_PAD_TO 0x1d000 62 63 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 64 CONFIG_SYS_MONITOR_LEN) 65 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 66 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 67 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 68 #define CONFIG_SYS_MONITOR_LEN 0xa0000 69 #endif 70 71 /* NAND SPL */ 72 #ifdef CONFIG_NAND_BOOT 73 #define CONFIG_SPL_PBL_PAD 74 #define CONFIG_SPL_FRAMEWORK 75 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" 76 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 77 #define CONFIG_SPL_TEXT_BASE 0x10000000 78 #define CONFIG_SPL_MAX_SIZE 0x1a000 79 #define CONFIG_SPL_STACK 0x1001d000 80 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 81 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 82 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 83 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 84 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 85 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 86 #define CONFIG_SYS_MONITOR_LEN 0xa0000 87 #endif 88 89 /* IFC */ 90 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 91 #define CONFIG_FSL_IFC 92 /* 93 * CONFIG_SYS_FLASH_BASE has the final address (core view) 94 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) 95 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address 96 * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting 97 */ 98 #define CONFIG_SYS_FLASH_BASE 0x60000000 99 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 100 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 101 102 #ifndef CONFIG_SYS_NO_FLASH 103 #define CONFIG_FLASH_CFI_DRIVER 104 #define CONFIG_SYS_FLASH_CFI 105 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 106 #define CONFIG_SYS_FLASH_QUIET_TEST 107 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 108 #endif 109 #endif 110 111 /* I2C */ 112 #define CONFIG_SYS_I2C 113 #define CONFIG_SYS_I2C_MXC 114 #define CONFIG_SYS_I2C_MXC_I2C1 115 #define CONFIG_SYS_I2C_MXC_I2C2 116 #define CONFIG_SYS_I2C_MXC_I2C3 117 #define CONFIG_SYS_I2C_MXC_I2C4 118 119 /* PCIe */ 120 #define CONFIG_PCI /* Enable PCI/PCIE */ 121 #define CONFIG_PCIE1 /* PCIE controller 1 */ 122 #define CONFIG_PCIE2 /* PCIE controller 2 */ 123 #define CONFIG_PCIE3 /* PCIE controller 3 */ 124 #define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ 125 #define FSL_PCIE_COMPAT "fsl,ls1043a-pcie" 126 127 #define CONFIG_SYS_PCI_64BIT 128 129 #define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 130 #define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ 131 #define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 132 #define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ 133 134 #define CONFIG_SYS_PCIE_IO_BUS 0x00000000 135 #define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 136 #define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ 137 138 #define CONFIG_SYS_PCIE_MEM_BUS 0x40000000 139 #define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000 140 #define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */ 141 142 #ifdef CONFIG_PCI 143 #define CONFIG_NET_MULTI 144 #define CONFIG_PCI_PNP 145 #define CONFIG_E1000 146 #define CONFIG_PCI_SCAN_SHOW 147 #define CONFIG_CMD_PCI 148 #endif 149 150 /* Command line configuration */ 151 #define CONFIG_CMD_ENV 152 #define CONFIG_MENU 153 #define CONFIG_CMD_PXE 154 155 /* MMC */ 156 #define CONFIG_MMC 157 #ifdef CONFIG_MMC 158 #define CONFIG_FSL_ESDHC 159 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 160 #define CONFIG_GENERIC_MMC 161 #define CONFIG_DOS_PARTITION 162 #endif 163 164 /* DSPI */ 165 #define CONFIG_FSL_DSPI 166 #ifdef CONFIG_FSL_DSPI 167 #define CONFIG_DM_SPI_FLASH 168 #define CONFIG_SPI_FLASH_STMICRO /* cs0 */ 169 #define CONFIG_SPI_FLASH_SST /* cs1 */ 170 #define CONFIG_SPI_FLASH_EON /* cs2 */ 171 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 172 #define CONFIG_SF_DEFAULT_BUS 1 173 #define CONFIG_SF_DEFAULT_CS 0 174 #endif 175 #endif 176 177 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 178 179 /* FMan ucode */ 180 #define CONFIG_SYS_DPAA_FMAN 181 #ifdef CONFIG_SYS_DPAA_FMAN 182 #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 183 184 #ifdef CONFIG_NAND_BOOT 185 /* Store Fman ucode at offeset 0x160000(11 blocks). */ 186 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 187 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE) 188 #elif defined(CONFIG_SD_BOOT) 189 /* 190 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 191 * about 1MB (2040 blocks), Env is stored after the image, and the env size is 192 * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820). 193 */ 194 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 195 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) 196 #elif defined(CONFIG_QSPI_BOOT) 197 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 198 #define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000 199 #define CONFIG_ENV_SPI_BUS 0 200 #define CONFIG_ENV_SPI_CS 0 201 #define CONFIG_ENV_SPI_MAX_HZ 1000000 202 #define CONFIG_ENV_SPI_MODE 0x03 203 #else 204 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 205 /* FMan fireware Pre-load address */ 206 #define CONFIG_SYS_FMAN_FW_ADDR 0x60300000 207 #endif 208 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 209 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 210 #endif 211 212 /* Miscellaneous configurable options */ 213 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 214 #define CONFIG_ARCH_EARLY_INIT_R 215 #define CONFIG_BOARD_LATE_INIT 216 217 #define CONFIG_HWCONFIG 218 #define HWCONFIG_BUFFER_SIZE 128 219 220 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 221 #define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \ 222 "5m(kernel),1m(dtb),9m(file_system)" 223 #else 224 #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \ 225 "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," \ 226 "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," \ 227 "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \ 228 "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \ 229 "40m(nor_bank4_fit);7e800000.flash:" \ 230 "1m(nand_uboot),1m(nand_uboot_env)," \ 231 "20m(nand_fit);spi0.0:1m(uboot)," \ 232 "5m(kernel),1m(dtb),9m(file_system)" 233 #endif 234 235 /* Initial environment variables */ 236 #define CONFIG_EXTRA_ENV_SETTINGS \ 237 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 238 "loadaddr=0x80100000\0" \ 239 "fdt_high=0xffffffffffffffff\0" \ 240 "initrd_high=0xffffffffffffffff\0" \ 241 "kernel_start=0x61100000\0" \ 242 "kernel_load=0xa0000000\0" \ 243 "kernel_size=0x2800000\0" \ 244 "console=ttyS0,115200\0" \ 245 "mtdparts=" MTDPARTS_DEFAULT "\0" 246 247 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ 248 "earlycon=uart8250,mmio,0x21c0500 " \ 249 MTDPARTS_DEFAULT 250 251 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 252 #define CONFIG_BOOTCOMMAND "sf probe && sf read $kernel_load " \ 253 "e0000 f00000 && bootm $kernel_load" 254 #else 255 #define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \ 256 "$kernel_size && bootm $kernel_load" 257 #endif 258 259 /* Monitor Command Prompt */ 260 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 261 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 262 sizeof(CONFIG_SYS_PROMPT) + 16) 263 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 264 #define CONFIG_SYS_LONGHELP 265 #define CONFIG_CMDLINE_EDITING 1 266 #define CONFIG_AUTO_COMPLETE 267 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 268 269 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 270 271 /* Hash command with SHA acceleration supported in hardware */ 272 #ifdef CONFIG_FSL_CAAM 273 #define CONFIG_CMD_HASH 274 #define CONFIG_SHA_HW_ACCEL 275 #endif 276 277 #endif /* __LS1043A_COMMON_H */ 278