1 /* 2 * Copyright (C) 2015 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS1043A_COMMON_H 8 #define __LS1043A_COMMON_H 9 10 /* SPL build */ 11 #ifdef CONFIG_SPL_BUILD 12 #define SPL_NO_FMAN 13 #define SPL_NO_DSPI 14 #define SPL_NO_PCIE 15 #define SPL_NO_ENV 16 #define SPL_NO_MISC 17 #define SPL_NO_USB 18 #define SPL_NO_SATA 19 #define SPL_NO_QE 20 #define SPL_NO_EEPROM 21 #endif 22 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT)) 23 #define SPL_NO_MMC 24 #endif 25 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI)) 26 #define SPL_NO_IFC 27 #endif 28 29 #define CONFIG_REMAKE_ELF 30 #define CONFIG_FSL_LAYERSCAPE 31 #define CONFIG_MP 32 #define CONFIG_GICV2 33 34 #include <asm/arch/stream_id_lsch2.h> 35 #include <asm/arch/config.h> 36 37 /* Link Definitions */ 38 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 39 40 #define CONFIG_SKIP_LOWLEVEL_INIT 41 42 #define CONFIG_VERY_BIG_RAM 43 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 44 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 45 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 46 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL 47 48 #define CPU_RELEASE_ADDR secondary_boot_func 49 50 /* Generic Timer Definitions */ 51 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 52 53 /* Size of malloc() pool */ 54 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) 55 56 /* Serial Port */ 57 #define CONFIG_CONS_INDEX 1 58 #define CONFIG_SYS_NS16550_SERIAL 59 #define CONFIG_SYS_NS16550_REG_SIZE 1 60 #define CONFIG_SYS_NS16550_CLK (get_serial_clock()) 61 62 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 63 64 /* SD boot SPL */ 65 #ifdef CONFIG_SD_BOOT 66 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 67 68 #define CONFIG_SPL_TEXT_BASE 0x10000000 69 #define CONFIG_SPL_MAX_SIZE 0x17000 70 #define CONFIG_SPL_STACK 0x1001e000 71 #define CONFIG_SPL_PAD_TO 0x1d000 72 73 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 74 CONFIG_SPL_BSS_MAX_SIZE) 75 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 76 #define CONFIG_SPL_BSS_START_ADDR 0x8f000000 77 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 78 79 #ifdef CONFIG_SECURE_BOOT 80 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 81 /* 82 * HDR would be appended at end of image and copied to DDR along 83 * with U-Boot image. Here u-boot max. size is 512K. So if binary 84 * size increases then increase this size in case of secure boot as 85 * it uses raw u-boot image instead of fit image. 86 */ 87 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 88 #else 89 #define CONFIG_SYS_MONITOR_LEN 0x100000 90 #endif /* ifdef CONFIG_SECURE_BOOT */ 91 #endif 92 93 /* NAND SPL */ 94 #ifdef CONFIG_NAND_BOOT 95 #define CONFIG_SPL_PBL_PAD 96 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 97 #define CONFIG_SPL_TEXT_BASE 0x10000000 98 #define CONFIG_SPL_MAX_SIZE 0x1a000 99 #define CONFIG_SPL_STACK 0x1001d000 100 #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 101 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 102 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 103 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 104 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 105 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 106 107 #ifdef CONFIG_SECURE_BOOT 108 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 109 #endif /* ifdef CONFIG_SECURE_BOOT */ 110 111 #ifdef CONFIG_U_BOOT_HDR_SIZE 112 /* 113 * HDR would be appended at end of image and copied to DDR along 114 * with U-Boot image. Here u-boot max. size is 512K. So if binary 115 * size increases then increase this size in case of secure boot as 116 * it uses raw u-boot image instead of fit image. 117 */ 118 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 119 #else 120 #define CONFIG_SYS_MONITOR_LEN 0x100000 121 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ 122 123 #endif 124 125 /* IFC */ 126 #ifndef SPL_NO_IFC 127 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 128 #define CONFIG_FSL_IFC 129 /* 130 * CONFIG_SYS_FLASH_BASE has the final address (core view) 131 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) 132 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address 133 * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting 134 */ 135 #define CONFIG_SYS_FLASH_BASE 0x60000000 136 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 137 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 138 139 #ifdef CONFIG_MTD_NOR_FLASH 140 #define CONFIG_FLASH_CFI_DRIVER 141 #define CONFIG_SYS_FLASH_CFI 142 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 143 #define CONFIG_SYS_FLASH_QUIET_TEST 144 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 145 #endif 146 #endif 147 #endif 148 149 /* I2C */ 150 #define CONFIG_SYS_I2C 151 152 /* PCIe */ 153 #ifndef SPL_NO_PCIE 154 #define CONFIG_PCIE1 /* PCIE controller 1 */ 155 #define CONFIG_PCIE2 /* PCIE controller 2 */ 156 #define CONFIG_PCIE3 /* PCIE controller 3 */ 157 158 #ifdef CONFIG_PCI 159 #define CONFIG_PCI_SCAN_SHOW 160 #endif 161 #endif 162 163 /* Command line configuration */ 164 165 /* MMC */ 166 #ifndef SPL_NO_MMC 167 #ifdef CONFIG_MMC 168 #define CONFIG_FSL_ESDHC 169 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 170 #endif 171 #endif 172 173 /* DSPI */ 174 #ifndef SPL_NO_DSPI 175 #define CONFIG_FSL_DSPI 176 #ifdef CONFIG_FSL_DSPI 177 #define CONFIG_DM_SPI_FLASH 178 #define CONFIG_SPI_FLASH_STMICRO /* cs0 */ 179 #define CONFIG_SPI_FLASH_SST /* cs1 */ 180 #define CONFIG_SPI_FLASH_EON /* cs2 */ 181 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 182 #define CONFIG_SF_DEFAULT_BUS 1 183 #define CONFIG_SF_DEFAULT_CS 0 184 #endif 185 #endif 186 #endif 187 188 /* FMan ucode */ 189 #ifndef SPL_NO_FMAN 190 #define CONFIG_SYS_DPAA_FMAN 191 #ifdef CONFIG_SYS_DPAA_FMAN 192 #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 193 194 #ifdef CONFIG_NAND_BOOT 195 /* Store Fman ucode at offeset 0x900000(72 blocks). */ 196 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 197 #define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE) 198 #elif defined(CONFIG_SD_BOOT) 199 /* 200 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 201 * about 1MB (2040 blocks), Env is stored after the image, and the env size is 202 * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800). 203 */ 204 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 205 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800) 206 #define CONFIG_SYS_QE_FW_ADDR (512 * 0x4a08) 207 #elif defined(CONFIG_QSPI_BOOT) 208 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 209 #define CONFIG_SYS_FMAN_FW_ADDR 0x40900000 210 #define CONFIG_ENV_SPI_BUS 0 211 #define CONFIG_ENV_SPI_CS 0 212 #define CONFIG_ENV_SPI_MAX_HZ 1000000 213 #define CONFIG_ENV_SPI_MODE 0x03 214 #else 215 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 216 /* FMan fireware Pre-load address */ 217 #define CONFIG_SYS_FMAN_FW_ADDR 0x60900000 218 #define CONFIG_SYS_QE_FW_ADDR 0x60940000 219 #endif 220 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 221 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 222 #endif 223 #endif 224 225 /* Miscellaneous configurable options */ 226 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 227 228 #define CONFIG_HWCONFIG 229 #define HWCONFIG_BUFFER_SIZE 128 230 231 #ifndef SPL_NO_MISC 232 #ifndef CONFIG_SPL_BUILD 233 #define BOOT_TARGET_DEVICES(func) \ 234 func(MMC, mmc, 0) \ 235 func(USB, usb, 0) 236 #include <config_distro_bootcmd.h> 237 #endif 238 239 /* Initial environment variables */ 240 #define CONFIG_EXTRA_ENV_SETTINGS \ 241 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 242 "fdt_high=0xffffffffffffffff\0" \ 243 "initrd_high=0xffffffffffffffff\0" \ 244 "fdt_addr=0x64f00000\0" \ 245 "kernel_addr=0x61000000\0" \ 246 "scriptaddr=0x80000000\0" \ 247 "scripthdraddr=0x80080000\0" \ 248 "fdtheader_addr_r=0x80100000\0" \ 249 "kernelheader_addr_r=0x80200000\0" \ 250 "kernel_addr_r=0x81000000\0" \ 251 "fdt_addr_r=0x90000000\0" \ 252 "load_addr=0xa0000000\0" \ 253 "kernelheader_addr=0x60800000\0" \ 254 "kernel_size=0x2800000\0" \ 255 "kernelheader_size=0x40000\0" \ 256 "kernel_addr_sd=0x8000\0" \ 257 "kernel_size_sd=0x14000\0" \ 258 "kernelhdr_addr_sd=0x4000\0" \ 259 "kernelhdr_size_sd=0x10\0" \ 260 "console=ttyS0,115200\0" \ 261 "boot_os=y\0" \ 262 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ 263 BOOTENV \ 264 "boot_scripts=ls1043ardb_boot.scr\0" \ 265 "boot_script_hdr=hdr_ls1043ardb_bs.out\0" \ 266 "scan_dev_for_boot_part=" \ 267 "part list ${devtype} ${devnum} devplist; " \ 268 "env exists devplist || setenv devplist 1; " \ 269 "for distro_bootpart in ${devplist}; do " \ 270 "if fstype ${devtype} " \ 271 "${devnum}:${distro_bootpart} " \ 272 "bootfstype; then " \ 273 "run scan_dev_for_boot; " \ 274 "fi; " \ 275 "done\0" \ 276 "scan_dev_for_boot=" \ 277 "echo Scanning ${devtype} " \ 278 "${devnum}:${distro_bootpart}...; " \ 279 "for prefix in ${boot_prefixes}; do " \ 280 "run scan_dev_for_scripts; " \ 281 "done;\0" \ 282 "boot_a_script=" \ 283 "load ${devtype} ${devnum}:${distro_bootpart} " \ 284 "${scriptaddr} ${prefix}${script}; " \ 285 "env exists secureboot && load ${devtype} " \ 286 "${devnum}:${distro_bootpart} " \ 287 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 288 "&& esbc_validate ${scripthdraddr};" \ 289 "source ${scriptaddr}\0" \ 290 "qspi_bootcmd=echo Trying load from qspi..;" \ 291 "sf probe && sf read $load_addr " \ 292 "$kernel_addr $kernel_size; env exists secureboot " \ 293 "&& sf read $kernelheader_addr_r $kernelheader_addr " \ 294 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \ 295 "bootm $load_addr#$board\0" \ 296 "nor_bootcmd=echo Trying load from nor..;" \ 297 "cp.b $kernel_addr $load_addr " \ 298 "$kernel_size; env exists secureboot " \ 299 "&& cp.b $kernelheader_addr $kernelheader_addr_r " \ 300 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \ 301 "bootm $load_addr#$board\0" \ 302 "sd_bootcmd=echo Trying load from SD ..;" \ 303 "mmcinfo; mmc read $load_addr " \ 304 "$kernel_addr_sd $kernel_size_sd && " \ 305 "env exists secureboot && mmc read $kernelheader_addr_r " \ 306 "$kernelhdr_addr_sd $kernelhdr_size_sd " \ 307 " && esbc_validate ${kernelheader_addr_r};" \ 308 "bootm $load_addr#$board\0" 309 310 311 #undef CONFIG_BOOTCOMMAND 312 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 313 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \ 314 "env exists secureboot && esbc_halt;" 315 #elif defined(CONFIG_SD_BOOT) 316 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \ 317 "env exists secureboot && esbc_halt;" 318 #else 319 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \ 320 "env exists secureboot && esbc_halt;" 321 #endif 322 #endif 323 324 /* Monitor Command Prompt */ 325 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 326 327 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 328 329 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 330 331 #include <asm/arch/soc.h> 332 333 #endif /* __LS1043A_COMMON_H */ 334