1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright (C) 2015 Freescale Semiconductor
4  */
5 
6 #ifndef __LS1043A_COMMON_H
7 #define __LS1043A_COMMON_H
8 
9 /* SPL build */
10 #ifdef CONFIG_SPL_BUILD
11 #define SPL_NO_FMAN
12 #define SPL_NO_DSPI
13 #define SPL_NO_PCIE
14 #define SPL_NO_ENV
15 #define SPL_NO_MISC
16 #define SPL_NO_USB
17 #define SPL_NO_SATA
18 #define SPL_NO_QE
19 #define SPL_NO_EEPROM
20 #endif
21 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT))
22 #define SPL_NO_MMC
23 #endif
24 #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI))
25 #define SPL_NO_IFC
26 #endif
27 
28 #define CONFIG_REMAKE_ELF
29 #define CONFIG_FSL_LAYERSCAPE
30 #define CONFIG_GICV2
31 
32 #include <asm/arch/stream_id_lsch2.h>
33 #include <asm/arch/config.h>
34 
35 /* Link Definitions */
36 #ifdef CONFIG_TFABOOT
37 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
38 #else
39 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
40 #endif
41 
42 #define CONFIG_SKIP_LOWLEVEL_INIT
43 
44 #define CONFIG_VERY_BIG_RAM
45 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
46 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
47 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
48 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
49 
50 #define CPU_RELEASE_ADDR               secondary_boot_func
51 
52 /* Generic Timer Definitions */
53 #define COUNTER_FREQUENCY		25000000	/* 25MHz */
54 
55 /* Size of malloc() pool */
56 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 1024 * 1024)
57 
58 /* Serial Port */
59 #define CONFIG_SYS_NS16550_SERIAL
60 #define CONFIG_SYS_NS16550_REG_SIZE	1
61 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
62 
63 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
64 
65 /* SD boot SPL */
66 #ifdef CONFIG_SD_BOOT
67 
68 #define CONFIG_SPL_TEXT_BASE		0x10000000
69 #define CONFIG_SPL_MAX_SIZE		0x17000
70 #define CONFIG_SPL_STACK		0x1001e000
71 #define CONFIG_SPL_PAD_TO		0x1d000
72 
73 #define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
74 					CONFIG_SPL_BSS_MAX_SIZE)
75 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
76 #define CONFIG_SPL_BSS_START_ADDR	0x8f000000
77 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
78 
79 #ifdef CONFIG_SECURE_BOOT
80 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
81 /*
82  * HDR would be appended at end of image and copied to DDR along
83  * with U-Boot image. Here u-boot max. size is 512K. So if binary
84  * size increases then increase this size in case of secure boot as
85  * it uses raw u-boot image instead of fit image.
86  */
87 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
88 #else
89 #define CONFIG_SYS_MONITOR_LEN		0x100000
90 #endif /* ifdef CONFIG_SECURE_BOOT */
91 #endif
92 
93 /* NAND SPL */
94 #ifdef CONFIG_NAND_BOOT
95 #define CONFIG_SPL_PBL_PAD
96 #define CONFIG_SPL_TEXT_BASE		0x10000000
97 #define CONFIG_SPL_MAX_SIZE		0x1a000
98 #define CONFIG_SPL_STACK		0x1001d000
99 #define CONFIG_SYS_NAND_U_BOOT_DST	CONFIG_SYS_TEXT_BASE
100 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
101 #define CONFIG_SYS_SPL_MALLOC_START	0x80200000
102 #define CONFIG_SPL_BSS_START_ADDR	0x80100000
103 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
104 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000
105 
106 #ifdef CONFIG_SECURE_BOOT
107 #define CONFIG_U_BOOT_HDR_SIZE				(16 << 10)
108 #endif /* ifdef CONFIG_SECURE_BOOT */
109 
110 #ifdef CONFIG_U_BOOT_HDR_SIZE
111 /*
112  * HDR would be appended at end of image and copied to DDR along
113  * with U-Boot image. Here u-boot max. size is 512K. So if binary
114  * size increases then increase this size in case of secure boot as
115  * it uses raw u-boot image instead of fit image.
116  */
117 #define CONFIG_SYS_MONITOR_LEN		(0x100000 + CONFIG_U_BOOT_HDR_SIZE)
118 #else
119 #define CONFIG_SYS_MONITOR_LEN		0x100000
120 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
121 
122 #endif
123 
124 /* IFC */
125 #ifndef SPL_NO_IFC
126 #if defined(CONFIG_TFABOOT) || \
127 	(!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI))
128 #define CONFIG_FSL_IFC
129 /*
130  * CONFIG_SYS_FLASH_BASE has the final address (core view)
131  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
132  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
133  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
134  */
135 #define CONFIG_SYS_FLASH_BASE			0x60000000
136 #define CONFIG_SYS_FLASH_BASE_PHYS		CONFIG_SYS_FLASH_BASE
137 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000
138 
139 #ifdef CONFIG_MTD_NOR_FLASH
140 #define CONFIG_SYS_FLASH_QUIET_TEST
141 #define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
142 #endif
143 #endif
144 #endif
145 
146 /* I2C */
147 #define CONFIG_SYS_I2C
148 
149 /* PCIe */
150 #ifndef SPL_NO_PCIE
151 #define CONFIG_PCIE1		/* PCIE controller 1 */
152 #define CONFIG_PCIE2		/* PCIE controller 2 */
153 #define CONFIG_PCIE3		/* PCIE controller 3 */
154 
155 #ifdef CONFIG_PCI
156 #define CONFIG_PCI_SCAN_SHOW
157 #endif
158 #endif
159 
160 /* Command line configuration */
161 
162 /*  MMC  */
163 #ifndef SPL_NO_MMC
164 #ifdef CONFIG_MMC
165 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
166 #endif
167 #endif
168 
169 /*  DSPI  */
170 #ifndef SPL_NO_DSPI
171 #define CONFIG_FSL_DSPI
172 #ifdef CONFIG_FSL_DSPI
173 #define CONFIG_DM_SPI_FLASH
174 #define CONFIG_SPI_FLASH_STMICRO	/* cs0 */
175 #define CONFIG_SPI_FLASH_SST		/* cs1 */
176 #define CONFIG_SPI_FLASH_EON		/* cs2 */
177 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
178 #define CONFIG_SF_DEFAULT_BUS		1
179 #define CONFIG_SF_DEFAULT_CS		0
180 #endif
181 #endif
182 #endif
183 
184 /* FMan ucode */
185 #ifndef SPL_NO_FMAN
186 #define CONFIG_SYS_DPAA_FMAN
187 #ifdef CONFIG_SYS_DPAA_FMAN
188 #define CONFIG_SYS_FM_MURAM_SIZE	0x60000
189 
190 #ifdef CONFIG_TFABOOT
191 #define CONFIG_SYS_FMAN_FW_ADDR		0x900000
192 #define CONFIG_SYS_QE_FW_ADDR		0x940000
193 
194 #define CONFIG_ENV_SPI_BUS		0
195 #define CONFIG_ENV_SPI_CS		0
196 #define CONFIG_ENV_SPI_MAX_HZ		1000000
197 #define CONFIG_ENV_SPI_MODE		0x03
198 
199 #else
200 #ifdef CONFIG_NAND_BOOT
201 /* Store Fman ucode at offeset 0x900000(72 blocks). */
202 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
203 #define CONFIG_SYS_FMAN_FW_ADDR		(72 * CONFIG_SYS_NAND_BLOCK_SIZE)
204 #elif defined(CONFIG_SD_BOOT)
205 /*
206  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
207  * about 1MB (2040 blocks), Env is stored after the image, and the env size is
208  * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
209  */
210 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
211 #define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x4800)
212 #define CONFIG_SYS_QE_FW_ADDR		(512 * 0x4a08)
213 #elif defined(CONFIG_QSPI_BOOT)
214 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
215 #define CONFIG_SYS_FMAN_FW_ADDR		0x40900000
216 #define CONFIG_ENV_SPI_BUS		0
217 #define CONFIG_ENV_SPI_CS		0
218 #define CONFIG_ENV_SPI_MAX_HZ		1000000
219 #define CONFIG_ENV_SPI_MODE		0x03
220 #else
221 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
222 /* FMan fireware Pre-load address */
223 #define CONFIG_SYS_FMAN_FW_ADDR		0x60900000
224 #define CONFIG_SYS_QE_FW_ADDR		0x60940000
225 #endif
226 #endif
227 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
228 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
229 #endif
230 #endif
231 
232 /* Miscellaneous configurable options */
233 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
234 
235 #define CONFIG_HWCONFIG
236 #define HWCONFIG_BUFFER_SIZE		128
237 
238 #ifndef SPL_NO_MISC
239 #ifndef CONFIG_SPL_BUILD
240 #define BOOT_TARGET_DEVICES(func) \
241 	func(MMC, mmc, 0) \
242 	func(USB, usb, 0)
243 #include <config_distro_bootcmd.h>
244 #endif
245 
246 /* Initial environment variables */
247 #define CONFIG_EXTRA_ENV_SETTINGS		\
248 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
249 	"fdt_high=0xffffffffffffffff\0"		\
250 	"initrd_high=0xffffffffffffffff\0"	\
251 	"fdt_addr=0x64f00000\0"		 	\
252 	"kernel_addr=0x61000000\0"		\
253 	"scriptaddr=0x80000000\0"		\
254 	"scripthdraddr=0x80080000\0"		\
255 	"fdtheader_addr_r=0x80100000\0"		\
256 	"kernelheader_addr_r=0x80200000\0"	\
257 	"kernel_addr_r=0x81000000\0"		\
258 	"fdt_addr_r=0x90000000\0"		\
259 	"load_addr=0xa0000000\0"		\
260 	"kernelheader_addr=0x60800000\0"	\
261 	"kernel_size=0x2800000\0"		\
262 	"kernelheader_size=0x40000\0"		\
263 	"kernel_addr_sd=0x8000\0"		\
264 	"kernel_size_sd=0x14000\0"		\
265 	"kernelhdr_addr_sd=0x4000\0"		\
266 	"kernelhdr_size_sd=0x10\0"		\
267 	"console=ttyS0,115200\0"		\
268 	"boot_os=y\0"				\
269 	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"	\
270 	BOOTENV					\
271 	"boot_scripts=ls1043ardb_boot.scr\0"	\
272 	"boot_script_hdr=hdr_ls1043ardb_bs.out\0"	\
273 	"scan_dev_for_boot_part="		\
274 		"part list ${devtype} ${devnum} devplist; "	\
275 		"env exists devplist || setenv devplist 1; "	\
276 		"for distro_bootpart in ${devplist}; do "	\
277 			"if fstype ${devtype} "			\
278 				"${devnum}:${distro_bootpart} "	\
279 				"bootfstype; then "		\
280 				"run scan_dev_for_boot; "	\
281 			"fi; "					\
282 		"done\0"			\
283 	"scan_dev_for_boot="					\
284 		"echo Scanning ${devtype} "			\
285 			"${devnum}:${distro_bootpart}...; "	\
286 		"for prefix in ${boot_prefixes}; do "		\
287 			"run scan_dev_for_scripts; "		\
288 		"done;\0"					\
289 	"boot_a_script="					\
290 		"load ${devtype} ${devnum}:${distro_bootpart} "	\
291 			"${scriptaddr} ${prefix}${script}; "	\
292 		"env exists secureboot && load ${devtype} "	\
293 			"${devnum}:${distro_bootpart} "		\
294 			"${scripthdraddr} ${prefix}${boot_script_hdr} "	\
295 			"&& esbc_validate ${scripthdraddr};"	\
296 		"source ${scriptaddr}\0"			\
297 	"qspi_bootcmd=echo Trying load from qspi..;"	\
298 		"sf probe && sf read $load_addr "	\
299 		"$kernel_addr $kernel_size; env exists secureboot "	\
300 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
301 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
302 		"bootm $load_addr#$board\0"	\
303 	"nor_bootcmd=echo Trying load from nor..;"	\
304 		"cp.b $kernel_addr $load_addr "	\
305 		"$kernel_size; env exists secureboot "	\
306 		"&& cp.b $kernelheader_addr $kernelheader_addr_r "	\
307 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
308 		"bootm $load_addr#$board\0"	    \
309 	"sd_bootcmd=echo Trying load from SD ..;"       \
310 		"mmcinfo; mmc read $load_addr "         \
311 		"$kernel_addr_sd $kernel_size_sd && "     \
312 		"env exists secureboot && mmc read $kernelheader_addr_r "		\
313 		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
314 		" && esbc_validate ${kernelheader_addr_r};"	\
315 		"bootm $load_addr#$board\0"
316 
317 
318 #undef CONFIG_BOOTCOMMAND
319 #ifdef CONFIG_TFABOOT
320 #define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "	\
321 			   "env exists secureboot && esbc_halt;"
322 #define SD_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; "  \
323 			   "env exists secureboot && esbc_halt;"
324 #define IFC_NOR_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; "	\
325 			   "env exists secureboot && esbc_halt;"
326 #else
327 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
328 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "	\
329 			   "env exists secureboot && esbc_halt;"
330 #elif defined(CONFIG_SD_BOOT)
331 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; "  \
332 			   "env exists secureboot && esbc_halt;"
333 #else
334 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; "	\
335 			   "env exists secureboot && esbc_halt;"
336 #endif
337 #endif
338 #endif
339 
340 /* Monitor Command Prompt */
341 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
342 
343 #define CONFIG_SYS_MAXARGS		64	/* max command args */
344 
345 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
346 
347 #include <asm/arch/soc.h>
348 
349 #endif /* __LS1043A_COMMON_H */
350