1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_ARMV7_PSCI_1_0 11 12 #define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR 13 14 #define CONFIG_SYS_FSL_CLK 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT 17 #define CONFIG_DEEP_SLEEP 18 19 /* 20 * Size of malloc() pool 21 */ 22 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) 23 24 #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE 26 27 /* 28 * USB 29 */ 30 31 /* 32 * EHCI Support - disbaled by default as 33 * there is no signal coming out of soc on 34 * this board for this controller. However, 35 * the silicon still has this controller, 36 * and anyone can use this controller by 37 * taking signals out on their board. 38 */ 39 40 /*#define CONFIG_HAS_FSL_DR_USB*/ 41 42 #ifdef CONFIG_HAS_FSL_DR_USB 43 #define CONFIG_USB_EHCI_FSL 44 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 45 #endif 46 47 /* XHCI Support - enabled by default */ 48 #define CONFIG_HAS_FSL_XHCI_USB 49 50 #ifdef CONFIG_HAS_FSL_XHCI_USB 51 #define CONFIG_USB_XHCI_FSL 52 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 53 #endif 54 55 #define CONFIG_SYS_CLK_FREQ 100000000 56 #define CONFIG_DDR_CLK_FREQ 100000000 57 58 #define DDR_SDRAM_CFG 0x470c0008 59 #define DDR_CS0_BNDS 0x008000bf 60 #define DDR_CS0_CONFIG 0x80014302 61 #define DDR_TIMING_CFG_0 0x50550004 62 #define DDR_TIMING_CFG_1 0xbcb38c56 63 #define DDR_TIMING_CFG_2 0x0040d120 64 #define DDR_TIMING_CFG_3 0x010e1000 65 #define DDR_TIMING_CFG_4 0x00000001 66 #define DDR_TIMING_CFG_5 0x03401400 67 #define DDR_SDRAM_CFG_2 0x00401010 68 #define DDR_SDRAM_MODE 0x00061c60 69 #define DDR_SDRAM_MODE_2 0x00180000 70 #define DDR_SDRAM_INTERVAL 0x18600618 71 #define DDR_DDR_WRLVL_CNTL 0x8655f605 72 #define DDR_DDR_WRLVL_CNTL_2 0x05060607 73 #define DDR_DDR_WRLVL_CNTL_3 0x05050505 74 #define DDR_DDR_CDR1 0x80040000 75 #define DDR_DDR_CDR2 0x00000001 76 #define DDR_SDRAM_CLK_CNTL 0x02000000 77 #define DDR_DDR_ZQ_CNTL 0x89080600 78 #define DDR_CS0_CONFIG_2 0 79 #define DDR_SDRAM_CFG_MEM_EN 0x80000000 80 #define SDRAM_CFG2_D_INIT 0x00000010 81 #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 82 #define SDRAM_CFG2_FRC_SR 0x80000000 83 #define SDRAM_CFG_BI 0x00000001 84 85 #ifdef CONFIG_RAMBOOT_PBL 86 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg 87 #endif 88 89 #ifdef CONFIG_SD_BOOT 90 #ifdef CONFIG_SD_BOOT_QSPI 91 #define CONFIG_SYS_FSL_PBL_RCW \ 92 board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg 93 #else 94 #define CONFIG_SYS_FSL_PBL_RCW \ 95 board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg 96 #endif 97 #define CONFIG_SPL_FRAMEWORK 98 99 #ifdef CONFIG_SECURE_BOOT 100 /* 101 * HDR would be appended at end of image and copied to DDR along 102 * with U-Boot image. 103 */ 104 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 105 #endif /* ifdef CONFIG_SECURE_BOOT */ 106 107 #define CONFIG_SPL_TEXT_BASE 0x10000000 108 #define CONFIG_SPL_MAX_SIZE 0x1a000 109 #define CONFIG_SPL_STACK 0x1001d000 110 #define CONFIG_SPL_PAD_TO 0x1c000 111 #define CONFIG_SYS_TEXT_BASE 0x82000000 112 113 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 114 CONFIG_SYS_MONITOR_LEN) 115 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 116 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 117 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 118 119 #ifdef CONFIG_U_BOOT_HDR_SIZE 120 /* 121 * HDR would be appended at end of image and copied to DDR along 122 * with U-Boot image. Here u-boot max. size is 512K. So if binary 123 * size increases then increase this size in case of secure boot as 124 * it uses raw u-boot image instead of fit image. 125 */ 126 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 127 #else 128 #define CONFIG_SYS_MONITOR_LEN 0x100000 129 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ 130 #endif 131 132 #ifdef CONFIG_QSPI_BOOT 133 #define CONFIG_SYS_TEXT_BASE 0x40100000 134 #endif 135 136 #ifndef CONFIG_SYS_TEXT_BASE 137 #define CONFIG_SYS_TEXT_BASE 0x60100000 138 #endif 139 140 #define CONFIG_NR_DRAM_BANKS 1 141 #define PHYS_SDRAM 0x80000000 142 #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) 143 144 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 145 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 146 147 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ 148 !defined(CONFIG_QSPI_BOOT) 149 #define CONFIG_U_QE 150 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 151 #endif 152 153 /* 154 * IFC Definitions 155 */ 156 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 157 #define CONFIG_FSL_IFC 158 #define CONFIG_SYS_FLASH_BASE 0x60000000 159 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 160 161 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 162 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 163 CSPR_PORT_SIZE_16 | \ 164 CSPR_MSEL_NOR | \ 165 CSPR_V) 166 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 167 168 /* NOR Flash Timing Params */ 169 #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 170 CSOR_NOR_TRHZ_80) 171 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 172 FTIM0_NOR_TEADC(0x5) | \ 173 FTIM0_NOR_TAVDS(0x0) | \ 174 FTIM0_NOR_TEAHC(0x5)) 175 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 176 FTIM1_NOR_TRAD_NOR(0x1A) | \ 177 FTIM1_NOR_TSEQRAD_NOR(0x13)) 178 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 179 FTIM2_NOR_TCH(0x4) | \ 180 FTIM2_NOR_TWP(0x1c) | \ 181 FTIM2_NOR_TWPH(0x0e)) 182 #define CONFIG_SYS_NOR_FTIM3 0 183 184 #define CONFIG_FLASH_CFI_DRIVER 185 #define CONFIG_SYS_FLASH_CFI 186 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 187 #define CONFIG_SYS_FLASH_QUIET_TEST 188 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 189 190 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 191 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 192 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 193 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 194 195 #define CONFIG_SYS_FLASH_EMPTY_INFO 196 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } 197 198 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 199 #define CONFIG_SYS_WRITE_SWAPPED_DATA 200 #endif 201 202 /* CPLD */ 203 204 #define CONFIG_SYS_CPLD_BASE 0x7fb00000 205 #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 206 207 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 208 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ 209 CSPR_PORT_SIZE_8 | \ 210 CSPR_MSEL_GPCM | \ 211 CSPR_V) 212 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) 213 #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 214 CSOR_NOR_NOR_MODE_AVD_NOR | \ 215 CSOR_NOR_TRHZ_80) 216 217 /* CPLD Timing parameters for IFC GPCM */ 218 #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ 219 FTIM0_GPCM_TEADC(0xf) | \ 220 FTIM0_GPCM_TEAHC(0xf)) 221 #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 222 FTIM1_GPCM_TRAD(0x3f)) 223 #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 224 FTIM2_GPCM_TCH(0xf) | \ 225 FTIM2_GPCM_TWP(0xff)) 226 #define CONFIG_SYS_FPGA_FTIM3 0x0 227 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 228 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 229 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 230 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 231 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 232 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 233 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 234 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 235 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT 236 #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR 237 #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK 238 #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR 239 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 240 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 241 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 242 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 243 244 /* 245 * Serial Port 246 */ 247 #ifdef CONFIG_LPUART 248 #define CONFIG_LPUART_32B_REG 249 #else 250 #define CONFIG_CONS_INDEX 1 251 #define CONFIG_SYS_NS16550_SERIAL 252 #ifndef CONFIG_DM_SERIAL 253 #define CONFIG_SYS_NS16550_REG_SIZE 1 254 #endif 255 #define CONFIG_SYS_NS16550_CLK get_serial_clock() 256 #endif 257 258 /* 259 * I2C 260 */ 261 #define CONFIG_SYS_I2C 262 #define CONFIG_SYS_I2C_MXC 263 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 264 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 265 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 266 267 /* EEPROM */ 268 #define CONFIG_ID_EEPROM 269 #define CONFIG_SYS_I2C_EEPROM_NXID 270 #define CONFIG_SYS_EEPROM_BUS_NUM 1 271 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 272 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 274 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 275 276 /* 277 * MMC 278 */ 279 #define CONFIG_FSL_ESDHC 280 281 /* SPI */ 282 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 283 /* QSPI */ 284 #define QSPI0_AMBA_BASE 0x40000000 285 #define FSL_QSPI_FLASH_SIZE (1 << 24) 286 #define FSL_QSPI_FLASH_NUM 2 287 288 /* DSPI */ 289 #endif 290 291 /* DM SPI */ 292 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) 293 #define CONFIG_DM_SPI_FLASH 294 #endif 295 296 /* 297 * Video 298 */ 299 #ifdef CONFIG_VIDEO_FSL_DCU_FB 300 #define CONFIG_VIDEO_LOGO 301 #define CONFIG_VIDEO_BMP_LOGO 302 303 #define CONFIG_FSL_DCU_SII9022A 304 #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 305 #define CONFIG_SYS_I2C_DVI_ADDR 0x39 306 #endif 307 308 /* 309 * eTSEC 310 */ 311 #define CONFIG_TSEC_ENET 312 313 #ifdef CONFIG_TSEC_ENET 314 #define CONFIG_MII 315 #define CONFIG_MII_DEFAULT_TSEC 1 316 #define CONFIG_TSEC1 1 317 #define CONFIG_TSEC1_NAME "eTSEC1" 318 #define CONFIG_TSEC2 1 319 #define CONFIG_TSEC2_NAME "eTSEC2" 320 #define CONFIG_TSEC3 1 321 #define CONFIG_TSEC3_NAME "eTSEC3" 322 323 #define TSEC1_PHY_ADDR 2 324 #define TSEC2_PHY_ADDR 0 325 #define TSEC3_PHY_ADDR 1 326 327 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 328 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 329 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 330 331 #define TSEC1_PHYIDX 0 332 #define TSEC2_PHYIDX 0 333 #define TSEC3_PHYIDX 0 334 335 #define CONFIG_ETHPRIME "eTSEC1" 336 337 #define CONFIG_PHY_ATHEROS 338 339 #define CONFIG_HAS_ETH0 340 #define CONFIG_HAS_ETH1 341 #define CONFIG_HAS_ETH2 342 #endif 343 344 /* PCIe */ 345 #define CONFIG_PCIE1 /* PCIE controller 1 */ 346 #define CONFIG_PCIE2 /* PCIE controller 2 */ 347 348 #ifdef CONFIG_PCI 349 #define CONFIG_PCI_SCAN_SHOW 350 #endif 351 352 #define CONFIG_CMDLINE_TAG 353 354 #define CONFIG_PEN_ADDR_BIG_ENDIAN 355 #define CONFIG_LAYERSCAPE_NS_ACCESS 356 #define CONFIG_SMP_PEN_ADDR 0x01ee0200 357 #define COUNTER_FREQUENCY 12500000 358 359 #define CONFIG_HWCONFIG 360 #define HWCONFIG_BUFFER_SIZE 256 361 362 #define CONFIG_FSL_DEVICE_DISABLE 363 364 #include <config_distro_defaults.h> 365 #define BOOT_TARGET_DEVICES(func) \ 366 func(MMC, mmc, 0) \ 367 func(USB, usb, 0) 368 #include <config_distro_bootcmd.h> 369 370 #ifdef CONFIG_LPUART 371 #define CONFIG_EXTRA_ENV_SETTINGS \ 372 "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ 373 "initrd_high=0xffffffff\0" \ 374 "fdt_high=0xffffffff\0" \ 375 "fdt_addr=0x64f00000\0" \ 376 "kernel_addr=0x65000000\0" \ 377 "scriptaddr=0x80000000\0" \ 378 "scripthdraddr=0x80080000\0" \ 379 "fdtheader_addr_r=0x80100000\0" \ 380 "kernelheader_addr_r=0x80200000\0" \ 381 "kernel_addr_r=0x81000000\0" \ 382 "fdt_addr_r=0x90000000\0" \ 383 "ramdisk_addr_r=0xa0000000\0" \ 384 "load_addr=0xa0000000\0" \ 385 "kernel_size=0x2800000\0" \ 386 BOOTENV \ 387 "boot_scripts=ls1021atwr_boot.scr\0" \ 388 "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \ 389 "scan_dev_for_boot_part=" \ 390 "part list ${devtype} ${devnum} devplist; " \ 391 "env exists devplist || setenv devplist 1; " \ 392 "for distro_bootpart in ${devplist}; do " \ 393 "if fstype ${devtype} " \ 394 "${devnum}:${distro_bootpart} " \ 395 "bootfstype; then " \ 396 "run scan_dev_for_boot; " \ 397 "fi; " \ 398 "done\0" \ 399 "scan_dev_for_boot=" \ 400 "echo Scanning ${devtype} " \ 401 "${devnum}:${distro_bootpart}...; " \ 402 "for prefix in ${boot_prefixes}; do " \ 403 "run scan_dev_for_scripts; " \ 404 "done;" \ 405 "\0" \ 406 "boot_a_script=" \ 407 "load ${devtype} ${devnum}:${distro_bootpart} " \ 408 "${scriptaddr} ${prefix}${script}; " \ 409 "env exists secureboot && load ${devtype} " \ 410 "${devnum}:${distro_bootpart} " \ 411 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 412 "&& esbc_validate ${scripthdraddr};" \ 413 "source ${scriptaddr}\0" \ 414 "installer=load mmc 0:2 $load_addr " \ 415 "/flex_installer_arm32.itb; " \ 416 "bootm $load_addr#ls1021atwr\0" \ 417 "qspi_bootcmd=echo Trying load from qspi..;" \ 418 "sf probe && sf read $load_addr " \ 419 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 420 "nor_bootcmd=echo Trying load from nor..;" \ 421 "cp.b $kernel_addr $load_addr " \ 422 "$kernel_size && bootm $load_addr#$board\0" 423 #else 424 #define CONFIG_EXTRA_ENV_SETTINGS \ 425 "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ 426 "initrd_high=0xffffffff\0" \ 427 "fdt_high=0xffffffff\0" \ 428 "fdt_addr=0x64f00000\0" \ 429 "kernel_addr=0x65000000\0" \ 430 "scriptaddr=0x80000000\0" \ 431 "scripthdraddr=0x80080000\0" \ 432 "fdtheader_addr_r=0x80100000\0" \ 433 "kernelheader_addr_r=0x80200000\0" \ 434 "kernel_addr_r=0x81000000\0" \ 435 "fdt_addr_r=0x90000000\0" \ 436 "ramdisk_addr_r=0xa0000000\0" \ 437 "load_addr=0xa0000000\0" \ 438 "kernel_size=0x2800000\0" \ 439 BOOTENV \ 440 "boot_scripts=ls1021atwr_boot.scr\0" \ 441 "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \ 442 "scan_dev_for_boot_part=" \ 443 "part list ${devtype} ${devnum} devplist; " \ 444 "env exists devplist || setenv devplist 1; " \ 445 "for distro_bootpart in ${devplist}; do " \ 446 "if fstype ${devtype} " \ 447 "${devnum}:${distro_bootpart} " \ 448 "bootfstype; then " \ 449 "run scan_dev_for_boot; " \ 450 "fi; " \ 451 "done\0" \ 452 "scan_dev_for_boot=" \ 453 "echo Scanning ${devtype} " \ 454 "${devnum}:${distro_bootpart}...; " \ 455 "for prefix in ${boot_prefixes}; do " \ 456 "run scan_dev_for_scripts; " \ 457 "done;" \ 458 "\0" \ 459 "boot_a_script=" \ 460 "load ${devtype} ${devnum}:${distro_bootpart} " \ 461 "${scriptaddr} ${prefix}${script}; " \ 462 "env exists secureboot && load ${devtype} " \ 463 "${devnum}:${distro_bootpart} " \ 464 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 465 "&& esbc_validate ${scripthdraddr};" \ 466 "source ${scriptaddr}\0" \ 467 "installer=load mmc 0:2 $load_addr " \ 468 "/flex_installer_arm32.itb; " \ 469 "bootm $load_addr#ls1021atwr\0" \ 470 "qspi_bootcmd=echo Trying load from qspi..;" \ 471 "sf probe && sf read $load_addr " \ 472 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 473 "nor_bootcmd=echo Trying load from nor..;" \ 474 "cp.b $kernel_addr $load_addr " \ 475 "$kernel_size && bootm $load_addr#$board\0" 476 #endif 477 478 #undef CONFIG_BOOTCOMMAND 479 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 480 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ 481 "&& esbc_halt; run qspi_bootcmd;" 482 #else 483 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ 484 "&& esbc_halt; run nor_bootcmd;" 485 #endif 486 487 /* 488 * Miscellaneous configurable options 489 */ 490 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 491 #define CONFIG_AUTO_COMPLETE 492 493 #define CONFIG_SYS_MEMTEST_START 0x80000000 494 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 495 496 #define CONFIG_SYS_LOAD_ADDR 0x82000000 497 498 #define CONFIG_LS102XA_STREAM_ID 499 500 #define CONFIG_SYS_INIT_SP_OFFSET \ 501 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 502 #define CONFIG_SYS_INIT_SP_ADDR \ 503 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 504 505 #ifdef CONFIG_SPL_BUILD 506 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 507 #else 508 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 509 #endif 510 511 #define CONFIG_SYS_QE_FW_ADDR 0x60940000 512 513 /* 514 * Environment 515 */ 516 #define CONFIG_ENV_OVERWRITE 517 518 #if defined(CONFIG_SD_BOOT) 519 #define CONFIG_ENV_OFFSET 0x300000 520 #define CONFIG_SYS_MMC_ENV_DEV 0 521 #define CONFIG_ENV_SIZE 0x20000 522 #elif defined(CONFIG_QSPI_BOOT) 523 #define CONFIG_ENV_SIZE 0x2000 524 #define CONFIG_ENV_OFFSET 0x300000 525 #define CONFIG_ENV_SECT_SIZE 0x10000 526 #else 527 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) 528 #define CONFIG_ENV_SIZE 0x20000 529 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 530 #endif 531 532 #define CONFIG_MISC_INIT_R 533 534 #include <asm/fsl_secure_boot.h> 535 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 536 537 #endif 538