1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_LS102XA 11 12 #define CONFIG_ARMV7_PSCI 13 14 #define CONFIG_SYS_GENERIC_BOARD 15 16 #define CONFIG_DISPLAY_CPUINFO 17 #define CONFIG_DISPLAY_BOARDINFO 18 19 #define CONFIG_SKIP_LOWLEVEL_INIT 20 #define CONFIG_BOARD_EARLY_INIT_F 21 #define CONFIG_DEEP_SLEEP 22 #ifdef CONFIG_DEEP_SLEEP 23 #define CONFIG_SILENT_CONSOLE 24 #endif 25 26 /* 27 * Size of malloc() pool 28 */ 29 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) 30 31 #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR 32 #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE 33 34 /* 35 * USB 36 */ 37 38 /* 39 * EHCI Support - disbaled by default as 40 * there is no signal coming out of soc on 41 * this board for this controller. However, 42 * the silicon still has this controller, 43 * and anyone can use this controller by 44 * taking signals out on their board. 45 */ 46 47 /*#define CONFIG_HAS_FSL_DR_USB*/ 48 49 #ifdef CONFIG_HAS_FSL_DR_USB 50 #define CONFIG_USB_EHCI 51 #define CONFIG_USB_EHCI_FSL 52 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 53 #endif 54 55 /* XHCI Support - enabled by default */ 56 #define CONFIG_HAS_FSL_XHCI_USB 57 58 #ifdef CONFIG_HAS_FSL_XHCI_USB 59 #define CONFIG_USB_XHCI_FSL 60 #define CONFIG_USB_XHCI_DWC3 61 #define CONFIG_USB_XHCI 62 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 63 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 64 #endif 65 66 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_XHCI_USB) 67 #define CONFIG_CMD_USB 68 #define CONFIG_USB_STORAGE 69 #define CONFIG_CMD_EXT2 70 #endif 71 72 /* 73 * Generic Timer Definitions 74 */ 75 #define GENERIC_TIMER_CLK 12500000 76 77 #define CONFIG_SYS_CLK_FREQ 100000000 78 #define CONFIG_DDR_CLK_FREQ 100000000 79 80 #define DDR_SDRAM_CFG 0x470c0008 81 #define DDR_CS0_BNDS 0x008000bf 82 #define DDR_CS0_CONFIG 0x80014302 83 #define DDR_TIMING_CFG_0 0x50550004 84 #define DDR_TIMING_CFG_1 0xbcb38c56 85 #define DDR_TIMING_CFG_2 0x0040d120 86 #define DDR_TIMING_CFG_3 0x010e1000 87 #define DDR_TIMING_CFG_4 0x00000001 88 #define DDR_TIMING_CFG_5 0x03401400 89 #define DDR_SDRAM_CFG_2 0x00401010 90 #define DDR_SDRAM_MODE 0x00061c60 91 #define DDR_SDRAM_MODE_2 0x00180000 92 #define DDR_SDRAM_INTERVAL 0x18600618 93 #define DDR_DDR_WRLVL_CNTL 0x8655f605 94 #define DDR_DDR_WRLVL_CNTL_2 0x05060607 95 #define DDR_DDR_WRLVL_CNTL_3 0x05050505 96 #define DDR_DDR_CDR1 0x80040000 97 #define DDR_DDR_CDR2 0x00000001 98 #define DDR_SDRAM_CLK_CNTL 0x02000000 99 #define DDR_DDR_ZQ_CNTL 0x89080600 100 #define DDR_CS0_CONFIG_2 0 101 #define DDR_SDRAM_CFG_MEM_EN 0x80000000 102 #define SDRAM_CFG2_D_INIT 0x00000010 103 #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 104 #define SDRAM_CFG2_FRC_SR 0x80000000 105 #define SDRAM_CFG_BI 0x00000001 106 107 #ifdef CONFIG_RAMBOOT_PBL 108 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg 109 #endif 110 111 #ifdef CONFIG_SD_BOOT 112 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/ls1021atwr/ls102xa_rcw_sd.cfg 113 #define CONFIG_SPL_FRAMEWORK 114 #define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" 115 #define CONFIG_SPL_LIBCOMMON_SUPPORT 116 #define CONFIG_SPL_LIBGENERIC_SUPPORT 117 #define CONFIG_SPL_ENV_SUPPORT 118 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT 119 #define CONFIG_SPL_I2C_SUPPORT 120 #define CONFIG_SPL_WATCHDOG_SUPPORT 121 #define CONFIG_SPL_SERIAL_SUPPORT 122 #define CONFIG_SPL_MMC_SUPPORT 123 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0xe8 124 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 125 126 #define CONFIG_SPL_TEXT_BASE 0x10000000 127 #define CONFIG_SPL_MAX_SIZE 0x1a000 128 #define CONFIG_SPL_STACK 0x1001d000 129 #define CONFIG_SPL_PAD_TO 0x1c000 130 #define CONFIG_SYS_TEXT_BASE 0x82000000 131 132 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 133 CONFIG_SYS_MONITOR_LEN) 134 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 135 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 136 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 137 #define CONFIG_SYS_MONITOR_LEN 0x80000 138 #endif 139 140 #ifdef CONFIG_QSPI_BOOT 141 #define CONFIG_SYS_TEXT_BASE 0x40010000 142 #define CONFIG_SYS_NO_FLASH 143 #endif 144 145 #ifndef CONFIG_SYS_TEXT_BASE 146 #define CONFIG_SYS_TEXT_BASE 0x60100000 147 #endif 148 149 #define CONFIG_NR_DRAM_BANKS 1 150 #define PHYS_SDRAM 0x80000000 151 #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) 152 153 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 154 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 155 156 #define CONFIG_SYS_HAS_SERDES 157 158 #define CONFIG_FSL_CAAM /* Enable CAAM */ 159 160 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ 161 !defined(CONFIG_QSPI_BOOT) 162 #define CONFIG_U_QE 163 #endif 164 165 /* 166 * IFC Definitions 167 */ 168 #ifndef CONFIG_QSPI_BOOT 169 #define CONFIG_FSL_IFC 170 #define CONFIG_SYS_FLASH_BASE 0x60000000 171 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 172 173 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 174 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 175 CSPR_PORT_SIZE_16 | \ 176 CSPR_MSEL_NOR | \ 177 CSPR_V) 178 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 179 180 /* NOR Flash Timing Params */ 181 #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 182 CSOR_NOR_TRHZ_80) 183 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 184 FTIM0_NOR_TEADC(0x5) | \ 185 FTIM0_NOR_TAVDS(0x0) | \ 186 FTIM0_NOR_TEAHC(0x5)) 187 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 188 FTIM1_NOR_TRAD_NOR(0x1A) | \ 189 FTIM1_NOR_TSEQRAD_NOR(0x13)) 190 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 191 FTIM2_NOR_TCH(0x4) | \ 192 FTIM2_NOR_TWP(0x1c) | \ 193 FTIM2_NOR_TWPH(0x0e)) 194 #define CONFIG_SYS_NOR_FTIM3 0 195 196 #define CONFIG_FLASH_CFI_DRIVER 197 #define CONFIG_SYS_FLASH_CFI 198 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 199 #define CONFIG_SYS_FLASH_QUIET_TEST 200 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 201 202 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 203 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 204 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 205 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 206 207 #define CONFIG_SYS_FLASH_EMPTY_INFO 208 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } 209 210 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 211 #define CONFIG_SYS_WRITE_SWAPPED_DATA 212 #endif 213 214 /* CPLD */ 215 216 #define CONFIG_SYS_CPLD_BASE 0x7fb00000 217 #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 218 219 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 220 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ 221 CSPR_PORT_SIZE_8 | \ 222 CSPR_MSEL_GPCM | \ 223 CSPR_V) 224 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) 225 #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 226 CSOR_NOR_NOR_MODE_AVD_NOR | \ 227 CSOR_NOR_TRHZ_80) 228 229 /* CPLD Timing parameters for IFC GPCM */ 230 #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ 231 FTIM0_GPCM_TEADC(0xf) | \ 232 FTIM0_GPCM_TEAHC(0xf)) 233 #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 234 FTIM1_GPCM_TRAD(0x3f)) 235 #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 236 FTIM2_GPCM_TCH(0xf) | \ 237 FTIM2_GPCM_TWP(0xff)) 238 #define CONFIG_SYS_FPGA_FTIM3 0x0 239 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 240 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 241 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 242 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 243 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 244 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 245 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 246 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 247 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT 248 #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR 249 #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK 250 #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR 251 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 252 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 253 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 254 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 255 256 /* 257 * Serial Port 258 */ 259 #ifdef CONFIG_LPUART 260 #define CONFIG_FSL_LPUART 261 #define CONFIG_LPUART_32B_REG 262 #else 263 #define CONFIG_CONS_INDEX 1 264 #define CONFIG_SYS_NS16550 265 #define CONFIG_SYS_NS16550_SERIAL 266 #define CONFIG_SYS_NS16550_REG_SIZE 1 267 #define CONFIG_SYS_NS16550_CLK get_serial_clock() 268 #endif 269 270 #define CONFIG_BAUDRATE 115200 271 272 /* 273 * I2C 274 */ 275 #define CONFIG_CMD_I2C 276 #define CONFIG_SYS_I2C 277 #define CONFIG_SYS_I2C_MXC 278 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 279 280 /* EEPROM */ 281 #ifndef CONFIG_SD_BOOT 282 #define CONFIG_ID_EEPROM 283 #define CONFIG_SYS_I2C_EEPROM_NXID 284 #define CONFIG_SYS_EEPROM_BUS_NUM 1 285 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 286 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 287 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 288 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 289 #endif 290 291 /* 292 * MMC 293 */ 294 #define CONFIG_MMC 295 #define CONFIG_CMD_MMC 296 #define CONFIG_FSL_ESDHC 297 #define CONFIG_GENERIC_MMC 298 299 #define CONFIG_CMD_FAT 300 #define CONFIG_DOS_PARTITION 301 302 /* SPI */ 303 #ifdef CONFIG_QSPI_BOOT 304 /* QSPI */ 305 #define CONFIG_FSL_QSPI 306 #define QSPI0_AMBA_BASE 0x40000000 307 #define FSL_QSPI_FLASH_SIZE (1 << 24) 308 #define FSL_QSPI_FLASH_NUM 2 309 #define CONFIG_SPI_FLASH_STMICRO 310 311 /* DM SPI */ 312 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) 313 #define CONFIG_CMD_SF 314 #define CONFIG_DM_SPI_FLASH 315 #endif 316 #endif 317 318 /* 319 * Video 320 */ 321 #define CONFIG_FSL_DCU_FB 322 323 #ifdef CONFIG_FSL_DCU_FB 324 #define CONFIG_VIDEO 325 #define CONFIG_CMD_BMP 326 #define CONFIG_CFB_CONSOLE 327 #define CONFIG_VGA_AS_SINGLE_DEVICE 328 #define CONFIG_VIDEO_LOGO 329 #define CONFIG_VIDEO_BMP_LOGO 330 331 #define CONFIG_FSL_DCU_SII9022A 332 #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 333 #define CONFIG_SYS_I2C_DVI_ADDR 0x39 334 #endif 335 336 /* 337 * eTSEC 338 */ 339 #define CONFIG_TSEC_ENET 340 341 #ifdef CONFIG_TSEC_ENET 342 #define CONFIG_MII 343 #define CONFIG_MII_DEFAULT_TSEC 1 344 #define CONFIG_TSEC1 1 345 #define CONFIG_TSEC1_NAME "eTSEC1" 346 #define CONFIG_TSEC2 1 347 #define CONFIG_TSEC2_NAME "eTSEC2" 348 #define CONFIG_TSEC3 1 349 #define CONFIG_TSEC3_NAME "eTSEC3" 350 351 #define TSEC1_PHY_ADDR 2 352 #define TSEC2_PHY_ADDR 0 353 #define TSEC3_PHY_ADDR 1 354 355 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 356 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 357 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 358 359 #define TSEC1_PHYIDX 0 360 #define TSEC2_PHYIDX 0 361 #define TSEC3_PHYIDX 0 362 363 #define CONFIG_ETHPRIME "eTSEC1" 364 365 #define CONFIG_PHY_GIGE 366 #define CONFIG_PHYLIB 367 #define CONFIG_PHY_ATHEROS 368 369 #define CONFIG_HAS_ETH0 370 #define CONFIG_HAS_ETH1 371 #define CONFIG_HAS_ETH2 372 #endif 373 374 /* PCIe */ 375 #define CONFIG_PCI /* Enable PCI/PCIE */ 376 #define CONFIG_PCIE1 /* PCIE controler 1 */ 377 #define CONFIG_PCIE2 /* PCIE controler 2 */ 378 #define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ 379 #define FSL_PCIE_COMPAT "fsl,ls1021a-pcie" 380 381 #define CONFIG_SYS_PCI_64BIT 382 383 #define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 384 #define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ 385 #define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 386 #define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ 387 388 #define CONFIG_SYS_PCIE_IO_BUS 0x00000000 389 #define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 390 #define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ 391 392 #define CONFIG_SYS_PCIE_MEM_BUS 0x08000000 393 #define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000 394 #define CONFIG_SYS_PCIE_MEM_SIZE 0x08000000 /* 128M */ 395 396 #ifdef CONFIG_PCI 397 #define CONFIG_PCI_PNP 398 #define CONFIG_E1000 399 #define CONFIG_PCI_SCAN_SHOW 400 #define CONFIG_CMD_PCI 401 #endif 402 403 #define CONFIG_CMD_PING 404 #define CONFIG_CMD_DHCP 405 #define CONFIG_CMD_MII 406 407 #define CONFIG_CMDLINE_TAG 408 #define CONFIG_CMDLINE_EDITING 409 410 #define CONFIG_ARMV7_NONSEC 411 #define CONFIG_ARMV7_VIRT 412 #define CONFIG_PEN_ADDR_BIG_ENDIAN 413 #define CONFIG_LS102XA_NS_ACCESS 414 #define CONFIG_SMP_PEN_ADDR 0x01ee0200 415 #define CONFIG_TIMER_CLK_FREQ 12500000 416 417 #define CONFIG_HWCONFIG 418 #define HWCONFIG_BUFFER_SIZE 128 419 420 #define CONFIG_BOOTDELAY 3 421 422 #ifdef CONFIG_LPUART 423 #define CONFIG_EXTRA_ENV_SETTINGS \ 424 "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ 425 "initrd_high=0xcfffffff\0" \ 426 "fdt_high=0xcfffffff\0" 427 #else 428 #define CONFIG_EXTRA_ENV_SETTINGS \ 429 "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ 430 "initrd_high=0xcfffffff\0" \ 431 "fdt_high=0xcfffffff\0" 432 #endif 433 434 /* 435 * Miscellaneous configurable options 436 */ 437 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 438 #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ 439 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 440 #define CONFIG_AUTO_COMPLETE 441 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 442 #define CONFIG_SYS_PBSIZE \ 443 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 444 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 445 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 446 447 #define CONFIG_CMD_GREPENV 448 #define CONFIG_CMD_MEMINFO 449 #define CONFIG_CMD_MEMTEST 450 #define CONFIG_SYS_MEMTEST_START 0x80000000 451 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 452 453 #define CONFIG_SYS_LOAD_ADDR 0x82000000 454 455 #define CONFIG_LS102XA_STREAM_ID 456 457 /* 458 * Stack sizes 459 * The stack sizes are set up in start.S using the settings below 460 */ 461 #define CONFIG_STACKSIZE (30 * 1024) 462 463 #define CONFIG_SYS_INIT_SP_OFFSET \ 464 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 465 #define CONFIG_SYS_INIT_SP_ADDR \ 466 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 467 468 #ifdef CONFIG_SPL_BUILD 469 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 470 #else 471 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 472 #endif 473 474 #define CONFIG_SYS_QE_FW_ADDR 0x67f40000 475 476 /* 477 * Environment 478 */ 479 #define CONFIG_ENV_OVERWRITE 480 481 #if defined(CONFIG_SD_BOOT) 482 #define CONFIG_ENV_OFFSET 0x100000 483 #define CONFIG_ENV_IS_IN_MMC 484 #define CONFIG_SYS_MMC_ENV_DEV 0 485 #define CONFIG_ENV_SIZE 0x20000 486 #elif defined(CONFIG_QSPI_BOOT) 487 #define CONFIG_ENV_IS_IN_SPI_FLASH 488 #define CONFIG_ENV_SIZE 0x2000 489 #define CONFIG_ENV_OFFSET 0x100000 490 #define CONFIG_ENV_SECT_SIZE 0x10000 491 #else 492 #define CONFIG_ENV_IS_IN_FLASH 493 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 494 #define CONFIG_ENV_SIZE 0x20000 495 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 496 #endif 497 498 #define CONFIG_OF_LIBFDT 499 #define CONFIG_OF_BOARD_SETUP 500 #define CONFIG_CMD_BOOTZ 501 502 #define CONFIG_MISC_INIT_R 503 504 /* Hash command with SHA acceleration supported in hardware */ 505 #define CONFIG_CMD_HASH 506 #define CONFIG_SHA_HW_ACCEL 507 508 #ifdef CONFIG_SECURE_BOOT 509 #define CONFIG_CMD_BLOB 510 #include <asm/fsl_secure_boot.h> 511 #endif 512 513 #endif 514