1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_ARMV7_PSCI_1_0 11 12 #define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR 13 14 #define CONFIG_SYS_FSL_CLK 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT 17 #define CONFIG_DEEP_SLEEP 18 19 /* 20 * Size of malloc() pool 21 */ 22 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) 23 24 #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE 26 27 /* 28 * USB 29 */ 30 31 /* 32 * EHCI Support - disbaled by default as 33 * there is no signal coming out of soc on 34 * this board for this controller. However, 35 * the silicon still has this controller, 36 * and anyone can use this controller by 37 * taking signals out on their board. 38 */ 39 40 /*#define CONFIG_HAS_FSL_DR_USB*/ 41 42 #ifdef CONFIG_HAS_FSL_DR_USB 43 #define CONFIG_USB_EHCI_FSL 44 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 45 #endif 46 47 /* XHCI Support - enabled by default */ 48 #define CONFIG_HAS_FSL_XHCI_USB 49 50 #ifdef CONFIG_HAS_FSL_XHCI_USB 51 #define CONFIG_USB_XHCI_FSL 52 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 53 #endif 54 55 #define CONFIG_SYS_CLK_FREQ 100000000 56 #define CONFIG_DDR_CLK_FREQ 100000000 57 58 #define DDR_SDRAM_CFG 0x470c0008 59 #define DDR_CS0_BNDS 0x008000bf 60 #define DDR_CS0_CONFIG 0x80014302 61 #define DDR_TIMING_CFG_0 0x50550004 62 #define DDR_TIMING_CFG_1 0xbcb38c56 63 #define DDR_TIMING_CFG_2 0x0040d120 64 #define DDR_TIMING_CFG_3 0x010e1000 65 #define DDR_TIMING_CFG_4 0x00000001 66 #define DDR_TIMING_CFG_5 0x03401400 67 #define DDR_SDRAM_CFG_2 0x00401010 68 #define DDR_SDRAM_MODE 0x00061c60 69 #define DDR_SDRAM_MODE_2 0x00180000 70 #define DDR_SDRAM_INTERVAL 0x18600618 71 #define DDR_DDR_WRLVL_CNTL 0x8655f605 72 #define DDR_DDR_WRLVL_CNTL_2 0x05060607 73 #define DDR_DDR_WRLVL_CNTL_3 0x05050505 74 #define DDR_DDR_CDR1 0x80040000 75 #define DDR_DDR_CDR2 0x00000001 76 #define DDR_SDRAM_CLK_CNTL 0x02000000 77 #define DDR_DDR_ZQ_CNTL 0x89080600 78 #define DDR_CS0_CONFIG_2 0 79 #define DDR_SDRAM_CFG_MEM_EN 0x80000000 80 #define SDRAM_CFG2_D_INIT 0x00000010 81 #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 82 #define SDRAM_CFG2_FRC_SR 0x80000000 83 #define SDRAM_CFG_BI 0x00000001 84 85 #ifdef CONFIG_RAMBOOT_PBL 86 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg 87 #endif 88 89 #ifdef CONFIG_SD_BOOT 90 #ifdef CONFIG_SD_BOOT_QSPI 91 #define CONFIG_SYS_FSL_PBL_RCW \ 92 board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg 93 #else 94 #define CONFIG_SYS_FSL_PBL_RCW \ 95 board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg 96 #endif 97 #define CONFIG_SPL_FRAMEWORK 98 #define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" 99 100 #ifdef CONFIG_SECURE_BOOT 101 /* 102 * HDR would be appended at end of image and copied to DDR along 103 * with U-Boot image. 104 */ 105 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 106 #endif /* ifdef CONFIG_SECURE_BOOT */ 107 108 #define CONFIG_SPL_TEXT_BASE 0x10000000 109 #define CONFIG_SPL_MAX_SIZE 0x1a000 110 #define CONFIG_SPL_STACK 0x1001d000 111 #define CONFIG_SPL_PAD_TO 0x1c000 112 #define CONFIG_SYS_TEXT_BASE 0x82000000 113 114 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 115 CONFIG_SYS_MONITOR_LEN) 116 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 117 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 118 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 119 120 #ifdef CONFIG_U_BOOT_HDR_SIZE 121 /* 122 * HDR would be appended at end of image and copied to DDR along 123 * with U-Boot image. Here u-boot max. size is 512K. So if binary 124 * size increases then increase this size in case of secure boot as 125 * it uses raw u-boot image instead of fit image. 126 */ 127 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 128 #else 129 #define CONFIG_SYS_MONITOR_LEN 0x100000 130 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ 131 #endif 132 133 #ifdef CONFIG_QSPI_BOOT 134 #define CONFIG_SYS_TEXT_BASE 0x40100000 135 #endif 136 137 #ifndef CONFIG_SYS_TEXT_BASE 138 #define CONFIG_SYS_TEXT_BASE 0x60100000 139 #endif 140 141 #define CONFIG_NR_DRAM_BANKS 1 142 #define PHYS_SDRAM 0x80000000 143 #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) 144 145 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 146 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 147 148 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ 149 !defined(CONFIG_QSPI_BOOT) 150 #define CONFIG_U_QE 151 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 152 #endif 153 154 /* 155 * IFC Definitions 156 */ 157 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 158 #define CONFIG_FSL_IFC 159 #define CONFIG_SYS_FLASH_BASE 0x60000000 160 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 161 162 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 163 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 164 CSPR_PORT_SIZE_16 | \ 165 CSPR_MSEL_NOR | \ 166 CSPR_V) 167 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 168 169 /* NOR Flash Timing Params */ 170 #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 171 CSOR_NOR_TRHZ_80) 172 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 173 FTIM0_NOR_TEADC(0x5) | \ 174 FTIM0_NOR_TAVDS(0x0) | \ 175 FTIM0_NOR_TEAHC(0x5)) 176 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 177 FTIM1_NOR_TRAD_NOR(0x1A) | \ 178 FTIM1_NOR_TSEQRAD_NOR(0x13)) 179 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 180 FTIM2_NOR_TCH(0x4) | \ 181 FTIM2_NOR_TWP(0x1c) | \ 182 FTIM2_NOR_TWPH(0x0e)) 183 #define CONFIG_SYS_NOR_FTIM3 0 184 185 #define CONFIG_FLASH_CFI_DRIVER 186 #define CONFIG_SYS_FLASH_CFI 187 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 188 #define CONFIG_SYS_FLASH_QUIET_TEST 189 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 190 191 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 192 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 193 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 194 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 195 196 #define CONFIG_SYS_FLASH_EMPTY_INFO 197 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } 198 199 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 200 #define CONFIG_SYS_WRITE_SWAPPED_DATA 201 #endif 202 203 /* CPLD */ 204 205 #define CONFIG_SYS_CPLD_BASE 0x7fb00000 206 #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 207 208 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 209 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ 210 CSPR_PORT_SIZE_8 | \ 211 CSPR_MSEL_GPCM | \ 212 CSPR_V) 213 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) 214 #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 215 CSOR_NOR_NOR_MODE_AVD_NOR | \ 216 CSOR_NOR_TRHZ_80) 217 218 /* CPLD Timing parameters for IFC GPCM */ 219 #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ 220 FTIM0_GPCM_TEADC(0xf) | \ 221 FTIM0_GPCM_TEAHC(0xf)) 222 #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 223 FTIM1_GPCM_TRAD(0x3f)) 224 #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 225 FTIM2_GPCM_TCH(0xf) | \ 226 FTIM2_GPCM_TWP(0xff)) 227 #define CONFIG_SYS_FPGA_FTIM3 0x0 228 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 229 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 230 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 231 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 232 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 233 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 234 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 235 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 236 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT 237 #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR 238 #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK 239 #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR 240 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 241 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 242 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 243 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 244 245 /* 246 * Serial Port 247 */ 248 #ifdef CONFIG_LPUART 249 #define CONFIG_LPUART_32B_REG 250 #else 251 #define CONFIG_CONS_INDEX 1 252 #define CONFIG_SYS_NS16550_SERIAL 253 #ifndef CONFIG_DM_SERIAL 254 #define CONFIG_SYS_NS16550_REG_SIZE 1 255 #endif 256 #define CONFIG_SYS_NS16550_CLK get_serial_clock() 257 #endif 258 259 /* 260 * I2C 261 */ 262 #define CONFIG_SYS_I2C 263 #define CONFIG_SYS_I2C_MXC 264 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 265 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 266 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 267 268 /* EEPROM */ 269 #define CONFIG_ID_EEPROM 270 #define CONFIG_SYS_I2C_EEPROM_NXID 271 #define CONFIG_SYS_EEPROM_BUS_NUM 1 272 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 273 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 274 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 275 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 276 277 /* 278 * MMC 279 */ 280 #define CONFIG_FSL_ESDHC 281 282 /* SPI */ 283 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 284 /* QSPI */ 285 #define QSPI0_AMBA_BASE 0x40000000 286 #define FSL_QSPI_FLASH_SIZE (1 << 24) 287 #define FSL_QSPI_FLASH_NUM 2 288 289 /* DSPI */ 290 #endif 291 292 /* DM SPI */ 293 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) 294 #define CONFIG_DM_SPI_FLASH 295 #endif 296 297 /* 298 * Video 299 */ 300 #ifdef CONFIG_VIDEO_FSL_DCU_FB 301 #define CONFIG_VIDEO_LOGO 302 #define CONFIG_VIDEO_BMP_LOGO 303 304 #define CONFIG_FSL_DCU_SII9022A 305 #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 306 #define CONFIG_SYS_I2C_DVI_ADDR 0x39 307 #endif 308 309 /* 310 * eTSEC 311 */ 312 #define CONFIG_TSEC_ENET 313 314 #ifdef CONFIG_TSEC_ENET 315 #define CONFIG_MII 316 #define CONFIG_MII_DEFAULT_TSEC 1 317 #define CONFIG_TSEC1 1 318 #define CONFIG_TSEC1_NAME "eTSEC1" 319 #define CONFIG_TSEC2 1 320 #define CONFIG_TSEC2_NAME "eTSEC2" 321 #define CONFIG_TSEC3 1 322 #define CONFIG_TSEC3_NAME "eTSEC3" 323 324 #define TSEC1_PHY_ADDR 2 325 #define TSEC2_PHY_ADDR 0 326 #define TSEC3_PHY_ADDR 1 327 328 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 329 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 330 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 331 332 #define TSEC1_PHYIDX 0 333 #define TSEC2_PHYIDX 0 334 #define TSEC3_PHYIDX 0 335 336 #define CONFIG_ETHPRIME "eTSEC1" 337 338 #define CONFIG_PHY_GIGE 339 #define CONFIG_PHYLIB 340 #define CONFIG_PHY_ATHEROS 341 342 #define CONFIG_HAS_ETH0 343 #define CONFIG_HAS_ETH1 344 #define CONFIG_HAS_ETH2 345 #endif 346 347 /* PCIe */ 348 #define CONFIG_PCIE1 /* PCIE controller 1 */ 349 #define CONFIG_PCIE2 /* PCIE controller 2 */ 350 351 #ifdef CONFIG_PCI 352 #define CONFIG_PCI_SCAN_SHOW 353 #define CONFIG_CMD_PCI 354 #endif 355 356 #define CONFIG_CMDLINE_TAG 357 358 #define CONFIG_PEN_ADDR_BIG_ENDIAN 359 #define CONFIG_LAYERSCAPE_NS_ACCESS 360 #define CONFIG_SMP_PEN_ADDR 0x01ee0200 361 #define COUNTER_FREQUENCY 12500000 362 363 #define CONFIG_HWCONFIG 364 #define HWCONFIG_BUFFER_SIZE 256 365 366 #define CONFIG_FSL_DEVICE_DISABLE 367 368 #include <config_distro_defaults.h> 369 #define BOOT_TARGET_DEVICES(func) \ 370 func(MMC, mmc, 0) \ 371 func(USB, usb, 0) 372 #include <config_distro_bootcmd.h> 373 374 #ifdef CONFIG_LPUART 375 #define CONFIG_EXTRA_ENV_SETTINGS \ 376 "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ 377 "initrd_high=0xffffffff\0" \ 378 "fdt_high=0xffffffff\0" \ 379 "fdt_addr=0x64f00000\0" \ 380 "kernel_addr=0x65000000\0" \ 381 "scriptaddr=0x80000000\0" \ 382 "scripthdraddr=0x80080000\0" \ 383 "fdtheader_addr_r=0x80100000\0" \ 384 "kernelheader_addr_r=0x80200000\0" \ 385 "kernel_addr_r=0x81000000\0" \ 386 "fdt_addr_r=0x90000000\0" \ 387 "ramdisk_addr_r=0xa0000000\0" \ 388 "load_addr=0xa0000000\0" \ 389 "kernel_size=0x2800000\0" \ 390 BOOTENV \ 391 "boot_scripts=ls1021atwr_boot.scr\0" \ 392 "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \ 393 "scan_dev_for_boot_part=" \ 394 "part list ${devtype} ${devnum} devplist; " \ 395 "env exists devplist || setenv devplist 1; " \ 396 "for distro_bootpart in ${devplist}; do " \ 397 "if fstype ${devtype} " \ 398 "${devnum}:${distro_bootpart} " \ 399 "bootfstype; then " \ 400 "run scan_dev_for_boot; " \ 401 "fi; " \ 402 "done\0" \ 403 "scan_dev_for_boot=" \ 404 "echo Scanning ${devtype} " \ 405 "${devnum}:${distro_bootpart}...; " \ 406 "for prefix in ${boot_prefixes}; do " \ 407 "run scan_dev_for_scripts; " \ 408 "done;" \ 409 "\0" \ 410 "boot_a_script=" \ 411 "load ${devtype} ${devnum}:${distro_bootpart} " \ 412 "${scriptaddr} ${prefix}${script}; " \ 413 "env exists secureboot && load ${devtype} " \ 414 "${devnum}:${distro_bootpart} " \ 415 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 416 "&& esbc_validate ${scripthdraddr};" \ 417 "source ${scriptaddr}\0" \ 418 "installer=load mmc 0:2 $load_addr " \ 419 "/flex_installer_arm32.itb; " \ 420 "bootm $load_addr#ls1021atwr\0" \ 421 "qspi_bootcmd=echo Trying load from qspi..;" \ 422 "sf probe && sf read $load_addr " \ 423 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 424 "nor_bootcmd=echo Trying load from nor..;" \ 425 "cp.b $kernel_addr $load_addr " \ 426 "$kernel_size && bootm $load_addr#$board\0" 427 #else 428 #define CONFIG_EXTRA_ENV_SETTINGS \ 429 "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ 430 "initrd_high=0xffffffff\0" \ 431 "fdt_high=0xffffffff\0" \ 432 "fdt_addr=0x64f00000\0" \ 433 "kernel_addr=0x65000000\0" \ 434 "scriptaddr=0x80000000\0" \ 435 "scripthdraddr=0x80080000\0" \ 436 "fdtheader_addr_r=0x80100000\0" \ 437 "kernelheader_addr_r=0x80200000\0" \ 438 "kernel_addr_r=0x81000000\0" \ 439 "fdt_addr_r=0x90000000\0" \ 440 "ramdisk_addr_r=0xa0000000\0" \ 441 "load_addr=0xa0000000\0" \ 442 "kernel_size=0x2800000\0" \ 443 BOOTENV \ 444 "boot_scripts=ls1021atwr_boot.scr\0" \ 445 "boot_script_hdr=hdr_ls1021atwr_bs.out\0" \ 446 "scan_dev_for_boot_part=" \ 447 "part list ${devtype} ${devnum} devplist; " \ 448 "env exists devplist || setenv devplist 1; " \ 449 "for distro_bootpart in ${devplist}; do " \ 450 "if fstype ${devtype} " \ 451 "${devnum}:${distro_bootpart} " \ 452 "bootfstype; then " \ 453 "run scan_dev_for_boot; " \ 454 "fi; " \ 455 "done\0" \ 456 "scan_dev_for_boot=" \ 457 "echo Scanning ${devtype} " \ 458 "${devnum}:${distro_bootpart}...; " \ 459 "for prefix in ${boot_prefixes}; do " \ 460 "run scan_dev_for_scripts; " \ 461 "done;" \ 462 "\0" \ 463 "boot_a_script=" \ 464 "load ${devtype} ${devnum}:${distro_bootpart} " \ 465 "${scriptaddr} ${prefix}${script}; " \ 466 "env exists secureboot && load ${devtype} " \ 467 "${devnum}:${distro_bootpart} " \ 468 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 469 "&& esbc_validate ${scripthdraddr};" \ 470 "source ${scriptaddr}\0" \ 471 "installer=load mmc 0:2 $load_addr " \ 472 "/flex_installer_arm32.itb; " \ 473 "bootm $load_addr#ls1021atwr\0" \ 474 "qspi_bootcmd=echo Trying load from qspi..;" \ 475 "sf probe && sf read $load_addr " \ 476 "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ 477 "nor_bootcmd=echo Trying load from nor..;" \ 478 "cp.b $kernel_addr $load_addr " \ 479 "$kernel_size && bootm $load_addr#$board\0" 480 #endif 481 482 #undef CONFIG_BOOTCOMMAND 483 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 484 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ 485 "&& esbc_halt; run qspi_bootcmd;" 486 #else 487 #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ 488 "&& esbc_halt; run nor_bootcmd;" 489 #endif 490 491 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0" 492 493 /* 494 * Miscellaneous configurable options 495 */ 496 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 497 #define CONFIG_AUTO_COMPLETE 498 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 499 #define CONFIG_SYS_PBSIZE \ 500 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 501 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 502 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 503 504 #define CONFIG_SYS_MEMTEST_START 0x80000000 505 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 506 507 #define CONFIG_SYS_LOAD_ADDR 0x82000000 508 509 #define CONFIG_LS102XA_STREAM_ID 510 511 #define CONFIG_SYS_INIT_SP_OFFSET \ 512 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 513 #define CONFIG_SYS_INIT_SP_ADDR \ 514 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 515 516 #ifdef CONFIG_SPL_BUILD 517 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 518 #else 519 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 520 #endif 521 522 #define CONFIG_SYS_QE_FW_ADDR 0x60940000 523 524 /* 525 * Environment 526 */ 527 #define CONFIG_ENV_OVERWRITE 528 529 #if defined(CONFIG_SD_BOOT) 530 #define CONFIG_ENV_OFFSET 0x300000 531 #define CONFIG_SYS_MMC_ENV_DEV 0 532 #define CONFIG_ENV_SIZE 0x20000 533 #elif defined(CONFIG_QSPI_BOOT) 534 #define CONFIG_ENV_SIZE 0x2000 535 #define CONFIG_ENV_OFFSET 0x300000 536 #define CONFIG_ENV_SECT_SIZE 0x10000 537 #else 538 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000) 539 #define CONFIG_ENV_SIZE 0x20000 540 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 541 #endif 542 543 #define CONFIG_MISC_INIT_R 544 545 #include <asm/fsl_secure_boot.h> 546 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 547 548 #endif 549