1 /* 2 * Copyright 2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 #define CONFIG_ARMV7_PSCI_1_0 11 12 #define CONFIG_ARMV7_SECURE_BASE OCRAM_BASE_S_ADDR 13 14 #define CONFIG_SYS_FSL_CLK 15 16 #define CONFIG_SKIP_LOWLEVEL_INIT 17 #define CONFIG_DEEP_SLEEP 18 19 /* 20 * Size of malloc() pool 21 */ 22 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 16 * 1024 * 1024) 23 24 #define CONFIG_SYS_INIT_RAM_ADDR OCRAM_BASE_ADDR 25 #define CONFIG_SYS_INIT_RAM_SIZE OCRAM_SIZE 26 27 /* 28 * USB 29 */ 30 31 /* 32 * EHCI Support - disbaled by default as 33 * there is no signal coming out of soc on 34 * this board for this controller. However, 35 * the silicon still has this controller, 36 * and anyone can use this controller by 37 * taking signals out on their board. 38 */ 39 40 /*#define CONFIG_HAS_FSL_DR_USB*/ 41 42 #ifdef CONFIG_HAS_FSL_DR_USB 43 #define CONFIG_USB_EHCI 44 #define CONFIG_USB_EHCI_FSL 45 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 46 #endif 47 48 /* XHCI Support - enabled by default */ 49 #define CONFIG_HAS_FSL_XHCI_USB 50 51 #ifdef CONFIG_HAS_FSL_XHCI_USB 52 #define CONFIG_USB_XHCI_FSL 53 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 54 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 55 #endif 56 57 #define CONFIG_SYS_CLK_FREQ 100000000 58 #define CONFIG_DDR_CLK_FREQ 100000000 59 60 #define DDR_SDRAM_CFG 0x470c0008 61 #define DDR_CS0_BNDS 0x008000bf 62 #define DDR_CS0_CONFIG 0x80014302 63 #define DDR_TIMING_CFG_0 0x50550004 64 #define DDR_TIMING_CFG_1 0xbcb38c56 65 #define DDR_TIMING_CFG_2 0x0040d120 66 #define DDR_TIMING_CFG_3 0x010e1000 67 #define DDR_TIMING_CFG_4 0x00000001 68 #define DDR_TIMING_CFG_5 0x03401400 69 #define DDR_SDRAM_CFG_2 0x00401010 70 #define DDR_SDRAM_MODE 0x00061c60 71 #define DDR_SDRAM_MODE_2 0x00180000 72 #define DDR_SDRAM_INTERVAL 0x18600618 73 #define DDR_DDR_WRLVL_CNTL 0x8655f605 74 #define DDR_DDR_WRLVL_CNTL_2 0x05060607 75 #define DDR_DDR_WRLVL_CNTL_3 0x05050505 76 #define DDR_DDR_CDR1 0x80040000 77 #define DDR_DDR_CDR2 0x00000001 78 #define DDR_SDRAM_CLK_CNTL 0x02000000 79 #define DDR_DDR_ZQ_CNTL 0x89080600 80 #define DDR_CS0_CONFIG_2 0 81 #define DDR_SDRAM_CFG_MEM_EN 0x80000000 82 #define SDRAM_CFG2_D_INIT 0x00000010 83 #define DDR_CDR2_VREF_TRAIN_EN 0x00000080 84 #define SDRAM_CFG2_FRC_SR 0x80000000 85 #define SDRAM_CFG_BI 0x00000001 86 87 #ifdef CONFIG_RAMBOOT_PBL 88 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/ls1021atwr/ls102xa_pbi.cfg 89 #endif 90 91 #ifdef CONFIG_SD_BOOT 92 #ifdef CONFIG_SD_BOOT_QSPI 93 #define CONFIG_SYS_FSL_PBL_RCW \ 94 board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg 95 #else 96 #define CONFIG_SYS_FSL_PBL_RCW \ 97 board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg 98 #endif 99 #define CONFIG_SPL_FRAMEWORK 100 #define CONFIG_SPL_LDSCRIPT "arch/$(ARCH)/cpu/u-boot-spl.lds" 101 102 #ifdef CONFIG_SECURE_BOOT 103 /* 104 * HDR would be appended at end of image and copied to DDR along 105 * with U-Boot image. 106 */ 107 #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) 108 #endif /* ifdef CONFIG_SECURE_BOOT */ 109 110 #define CONFIG_SPL_TEXT_BASE 0x10000000 111 #define CONFIG_SPL_MAX_SIZE 0x1a000 112 #define CONFIG_SPL_STACK 0x1001d000 113 #define CONFIG_SPL_PAD_TO 0x1c000 114 #define CONFIG_SYS_TEXT_BASE 0x82000000 115 116 #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ 117 CONFIG_SYS_MONITOR_LEN) 118 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 119 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 120 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 121 122 #ifdef CONFIG_U_BOOT_HDR_SIZE 123 /* 124 * HDR would be appended at end of image and copied to DDR along 125 * with U-Boot image. Here u-boot max. size is 512K. So if binary 126 * size increases then increase this size in case of secure boot as 127 * it uses raw u-boot image instead of fit image. 128 */ 129 #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) 130 #else 131 #define CONFIG_SYS_MONITOR_LEN 0x100000 132 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ 133 #endif 134 135 #ifdef CONFIG_QSPI_BOOT 136 #define CONFIG_SYS_TEXT_BASE 0x40010000 137 #endif 138 139 #ifndef CONFIG_SYS_TEXT_BASE 140 #define CONFIG_SYS_TEXT_BASE 0x60100000 141 #endif 142 143 #define CONFIG_NR_DRAM_BANKS 1 144 #define PHYS_SDRAM 0x80000000 145 #define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) 146 147 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 148 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 149 150 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \ 151 !defined(CONFIG_QSPI_BOOT) 152 #define CONFIG_U_QE 153 #endif 154 155 /* 156 * IFC Definitions 157 */ 158 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) 159 #define CONFIG_FSL_IFC 160 #define CONFIG_SYS_FLASH_BASE 0x60000000 161 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 162 163 #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) 164 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 165 CSPR_PORT_SIZE_16 | \ 166 CSPR_MSEL_NOR | \ 167 CSPR_V) 168 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 169 170 /* NOR Flash Timing Params */ 171 #define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 172 CSOR_NOR_TRHZ_80) 173 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ 174 FTIM0_NOR_TEADC(0x5) | \ 175 FTIM0_NOR_TAVDS(0x0) | \ 176 FTIM0_NOR_TEAHC(0x5)) 177 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 178 FTIM1_NOR_TRAD_NOR(0x1A) | \ 179 FTIM1_NOR_TSEQRAD_NOR(0x13)) 180 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ 181 FTIM2_NOR_TCH(0x4) | \ 182 FTIM2_NOR_TWP(0x1c) | \ 183 FTIM2_NOR_TWPH(0x0e)) 184 #define CONFIG_SYS_NOR_FTIM3 0 185 186 #define CONFIG_FLASH_CFI_DRIVER 187 #define CONFIG_SYS_FLASH_CFI 188 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 189 #define CONFIG_SYS_FLASH_QUIET_TEST 190 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 191 192 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 193 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 194 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 195 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 196 197 #define CONFIG_SYS_FLASH_EMPTY_INFO 198 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS } 199 200 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 201 #define CONFIG_SYS_WRITE_SWAPPED_DATA 202 #endif 203 204 /* CPLD */ 205 206 #define CONFIG_SYS_CPLD_BASE 0x7fb00000 207 #define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE 208 209 #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) 210 #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \ 211 CSPR_PORT_SIZE_8 | \ 212 CSPR_MSEL_GPCM | \ 213 CSPR_V) 214 #define CONFIG_SYS_FPGA_AMASK IFC_AMASK(64 * 1024) 215 #define CONFIG_SYS_FPGA_CSOR (CSOR_NOR_ADM_SHIFT(4) | \ 216 CSOR_NOR_NOR_MODE_AVD_NOR | \ 217 CSOR_NOR_TRHZ_80) 218 219 /* CPLD Timing parameters for IFC GPCM */ 220 #define CONFIG_SYS_FPGA_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \ 221 FTIM0_GPCM_TEADC(0xf) | \ 222 FTIM0_GPCM_TEAHC(0xf)) 223 #define CONFIG_SYS_FPGA_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ 224 FTIM1_GPCM_TRAD(0x3f)) 225 #define CONFIG_SYS_FPGA_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ 226 FTIM2_GPCM_TCH(0xf) | \ 227 FTIM2_GPCM_TWP(0xff)) 228 #define CONFIG_SYS_FPGA_FTIM3 0x0 229 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 230 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 231 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 232 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 233 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 234 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 235 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 236 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 237 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_FPGA_CSPR_EXT 238 #define CONFIG_SYS_CSPR1 CONFIG_SYS_FPGA_CSPR 239 #define CONFIG_SYS_AMASK1 CONFIG_SYS_FPGA_AMASK 240 #define CONFIG_SYS_CSOR1 CONFIG_SYS_FPGA_CSOR 241 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_FPGA_FTIM0 242 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_FPGA_FTIM1 243 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_FPGA_FTIM2 244 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_FPGA_FTIM3 245 246 /* 247 * Serial Port 248 */ 249 #ifdef CONFIG_LPUART 250 #define CONFIG_LPUART_32B_REG 251 #else 252 #define CONFIG_CONS_INDEX 1 253 #define CONFIG_SYS_NS16550_SERIAL 254 #ifndef CONFIG_DM_SERIAL 255 #define CONFIG_SYS_NS16550_REG_SIZE 1 256 #endif 257 #define CONFIG_SYS_NS16550_CLK get_serial_clock() 258 #endif 259 260 /* 261 * I2C 262 */ 263 #define CONFIG_SYS_I2C 264 #define CONFIG_SYS_I2C_MXC 265 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 266 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 267 #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ 268 269 /* EEPROM */ 270 #define CONFIG_ID_EEPROM 271 #define CONFIG_SYS_I2C_EEPROM_NXID 272 #define CONFIG_SYS_EEPROM_BUS_NUM 1 273 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 274 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 275 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 276 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 277 278 /* 279 * MMC 280 */ 281 #define CONFIG_FSL_ESDHC 282 283 /* SPI */ 284 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) 285 /* QSPI */ 286 #define QSPI0_AMBA_BASE 0x40000000 287 #define FSL_QSPI_FLASH_SIZE (1 << 24) 288 #define FSL_QSPI_FLASH_NUM 2 289 290 /* DSPI */ 291 #endif 292 293 /* DM SPI */ 294 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) 295 #define CONFIG_DM_SPI_FLASH 296 #endif 297 298 /* 299 * Video 300 */ 301 #ifdef CONFIG_VIDEO_FSL_DCU_FB 302 #define CONFIG_CMD_BMP 303 #define CONFIG_VIDEO_LOGO 304 #define CONFIG_VIDEO_BMP_LOGO 305 306 #define CONFIG_FSL_DCU_SII9022A 307 #define CONFIG_SYS_I2C_DVI_BUS_NUM 1 308 #define CONFIG_SYS_I2C_DVI_ADDR 0x39 309 #endif 310 311 /* 312 * eTSEC 313 */ 314 #define CONFIG_TSEC_ENET 315 316 #ifdef CONFIG_TSEC_ENET 317 #define CONFIG_MII 318 #define CONFIG_MII_DEFAULT_TSEC 1 319 #define CONFIG_TSEC1 1 320 #define CONFIG_TSEC1_NAME "eTSEC1" 321 #define CONFIG_TSEC2 1 322 #define CONFIG_TSEC2_NAME "eTSEC2" 323 #define CONFIG_TSEC3 1 324 #define CONFIG_TSEC3_NAME "eTSEC3" 325 326 #define TSEC1_PHY_ADDR 2 327 #define TSEC2_PHY_ADDR 0 328 #define TSEC3_PHY_ADDR 1 329 330 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 331 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 332 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 333 334 #define TSEC1_PHYIDX 0 335 #define TSEC2_PHYIDX 0 336 #define TSEC3_PHYIDX 0 337 338 #define CONFIG_ETHPRIME "eTSEC1" 339 340 #define CONFIG_PHY_GIGE 341 #define CONFIG_PHYLIB 342 #define CONFIG_PHY_ATHEROS 343 344 #define CONFIG_HAS_ETH0 345 #define CONFIG_HAS_ETH1 346 #define CONFIG_HAS_ETH2 347 #endif 348 349 /* PCIe */ 350 #define CONFIG_PCIE1 /* PCIE controller 1 */ 351 #define CONFIG_PCIE2 /* PCIE controller 2 */ 352 353 #ifdef CONFIG_PCI 354 #define CONFIG_PCI_SCAN_SHOW 355 #define CONFIG_CMD_PCI 356 #endif 357 358 #define CONFIG_CMDLINE_TAG 359 #define CONFIG_CMDLINE_EDITING 360 361 #define CONFIG_PEN_ADDR_BIG_ENDIAN 362 #define CONFIG_LAYERSCAPE_NS_ACCESS 363 #define CONFIG_SMP_PEN_ADDR 0x01ee0200 364 #define COUNTER_FREQUENCY 12500000 365 366 #define CONFIG_HWCONFIG 367 #define HWCONFIG_BUFFER_SIZE 256 368 369 #define CONFIG_FSL_DEVICE_DISABLE 370 371 372 #ifdef CONFIG_LPUART 373 #define CONFIG_EXTRA_ENV_SETTINGS \ 374 "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ 375 "initrd_high=0xffffffff\0" \ 376 "fdt_high=0xffffffff\0" 377 #else 378 #define CONFIG_EXTRA_ENV_SETTINGS \ 379 "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ 380 "initrd_high=0xffffffff\0" \ 381 "fdt_high=0xffffffff\0" 382 #endif 383 384 /* 385 * Miscellaneous configurable options 386 */ 387 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 388 #define CONFIG_AUTO_COMPLETE 389 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 390 #define CONFIG_SYS_PBSIZE \ 391 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 392 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 393 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 394 395 #define CONFIG_SYS_MEMTEST_START 0x80000000 396 #define CONFIG_SYS_MEMTEST_END 0x9fffffff 397 398 #define CONFIG_SYS_LOAD_ADDR 0x82000000 399 400 #define CONFIG_LS102XA_STREAM_ID 401 402 #define CONFIG_SYS_INIT_SP_OFFSET \ 403 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 404 #define CONFIG_SYS_INIT_SP_ADDR \ 405 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 406 407 #ifdef CONFIG_SPL_BUILD 408 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 409 #else 410 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 411 #endif 412 413 #define CONFIG_SYS_QE_FW_ADDR 0x600c0000 414 415 /* 416 * Environment 417 */ 418 #define CONFIG_ENV_OVERWRITE 419 420 #if defined(CONFIG_SD_BOOT) 421 #define CONFIG_ENV_OFFSET 0x100000 422 #define CONFIG_ENV_IS_IN_MMC 423 #define CONFIG_SYS_MMC_ENV_DEV 0 424 #define CONFIG_ENV_SIZE 0x20000 425 #elif defined(CONFIG_QSPI_BOOT) 426 #define CONFIG_ENV_IS_IN_SPI_FLASH 427 #define CONFIG_ENV_SIZE 0x2000 428 #define CONFIG_ENV_OFFSET 0x100000 429 #define CONFIG_ENV_SECT_SIZE 0x10000 430 #else 431 #define CONFIG_ENV_IS_IN_FLASH 432 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 433 #define CONFIG_ENV_SIZE 0x20000 434 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 435 #endif 436 437 #define CONFIG_MISC_INIT_R 438 439 /* Hash command with SHA acceleration supported in hardware */ 440 #ifdef CONFIG_FSL_CAAM 441 #define CONFIG_CMD_HASH 442 #define CONFIG_SHA_HW_ACCEL 443 #endif 444 445 #include <asm/fsl_secure_boot.h> 446 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 447 448 #endif 449