1 /* 2 * Copyright 2016 Freescale Semiconductor 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __LS1012A_COMMON_H 8 #define __LS1012A_COMMON_H 9 10 #define CONFIG_FSL_LAYERSCAPE 11 #define CONFIG_GICV2 12 13 #include <asm/arch/config.h> 14 15 #define CONFIG_SUPPORT_RAW_INITRD 16 17 #define CONFIG_DISPLAY_BOARDINFO_LATE 18 19 #define CONFIG_SYS_TEXT_BASE 0x40100000 20 21 #define CONFIG_SYS_CLK_FREQ 125000000 22 23 #define CONFIG_SKIP_LOWLEVEL_INIT 24 25 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 26 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 27 28 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 29 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 30 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 31 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL 32 33 /* Generic Timer Definitions */ 34 #define COUNTER_FREQUENCY CONFIG_SYS_CLK_FREQ/4 /* 25MHz */ 35 36 /* CSU */ 37 #define CONFIG_LAYERSCAPE_NS_ACCESS 38 39 /* Size of malloc() pool */ 40 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) 41 42 /*SPI device */ 43 #ifdef CONFIG_QSPI_BOOT 44 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 45 #define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000 46 #define CONFIG_ENV_SPI_BUS 0 47 #define CONFIG_ENV_SPI_CS 0 48 #define CONFIG_ENV_SPI_MAX_HZ 1000000 49 #define CONFIG_ENV_SPI_MODE 0x03 50 #define CONFIG_SPI_FLASH_SPANSION 51 #define CONFIG_FSL_SPI_INTERFACE 52 #define CONFIG_SF_DATAFLASH 53 54 #define CONFIG_FSL_QSPI 55 #define QSPI0_AMBA_BASE 0x40000000 56 #define CONFIG_SPI_FLASH_SPANSION 57 #define CONFIG_SPI_FLASH_BAR 58 59 #define FSL_QSPI_FLASH_SIZE (1 << 24) 60 #define FSL_QSPI_FLASH_NUM 2 61 62 /* 63 * Environment 64 */ 65 #define CONFIG_ENV_OVERWRITE 66 67 #define CONFIG_ENV_IS_IN_SPI_FLASH 68 #define CONFIG_ENV_SIZE 0x40000 /* 256KB */ 69 #define CONFIG_ENV_OFFSET 0x200000 /* 2MB */ 70 #define CONFIG_ENV_SECT_SIZE 0x40000 71 #endif 72 73 /* I2C */ 74 #define CONFIG_SYS_I2C 75 #define CONFIG_SYS_I2C_MXC 76 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 77 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 78 79 #define CONFIG_CONS_INDEX 1 80 #define CONFIG_SYS_NS16550_SERIAL 81 #define CONFIG_SYS_NS16550_REG_SIZE 1 82 #define CONFIG_SYS_NS16550_CLK (get_serial_clock()) 83 84 #define CONFIG_BAUDRATE 115200 85 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 86 87 /* Command line configuration */ 88 #define CONFIG_CMD_ENV 89 #undef CONFIG_CMD_IMLS 90 91 #define CONFIG_SYS_HZ 1000 92 93 #define CONFIG_HWCONFIG 94 #define HWCONFIG_BUFFER_SIZE 128 95 96 /* Initial environment variables */ 97 #define CONFIG_EXTRA_ENV_SETTINGS \ 98 "verify=no\0" \ 99 "loadaddr=0x80100000\0" \ 100 "kernel_addr=0x100000\0" \ 101 "fdt_high=0xffffffffffffffff\0" \ 102 "initrd_high=0xffffffffffffffff\0" \ 103 "kernel_start=0xa00000\0" \ 104 "kernel_load=0xa0000000\0" \ 105 "kernel_size=0x2800000\0" \ 106 107 #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ 108 "earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" 109 #define CONFIG_BOOTCOMMAND "sf probe 0:0; sf read $kernel_load "\ 110 "$kernel_start $kernel_size && "\ 111 "bootm $kernel_load" 112 113 /* Monitor Command Prompt */ 114 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 115 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 116 sizeof(CONFIG_SYS_PROMPT) + 16) 117 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 118 #define CONFIG_SYS_LONGHELP 119 #define CONFIG_CMDLINE_EDITING 1 120 #define CONFIG_AUTO_COMPLETE 121 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 122 123 #define CONFIG_PANIC_HANG 124 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 125 126 #include <asm/fsl_secure_boot.h> 127 128 #endif /* __LS1012A_COMMON_H */ 129