1 /* 2 * (C) Copyright 2013 Keymile AG 3 * Valentin Longchamp <valentin.longchamp@keymile.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef _CONFIG_KMP204X_H 9 #define _CONFIG_KMP204X_H 10 11 #define CONFIG_PHYS_64BIT 12 #define CONFIG_PPC_P2041 13 14 #define CONFIG_SYS_TEXT_BASE 0xfff40000 15 16 #define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" 17 18 /* an additionnal option is required for UBI as subpage access is 19 * supported in u-boot */ 20 #define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" 21 22 #define CONFIG_NAND_ECC_BCH 23 24 #define CONFIG_SYS_GENERIC_BOARD 25 #define CONFIG_DISPLAY_BOARDINFO 26 27 /* common KM defines */ 28 #include "keymile-common.h" 29 30 #define CONFIG_SYS_RAMBOOT 31 #define CONFIG_RAMBOOT_PBL 32 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 33 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 34 #define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg 35 #define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg 36 37 /* High Level Configuration Options */ 38 #define CONFIG_BOOKE 39 #define CONFIG_E500 /* BOOKE e500 family */ 40 #define CONFIG_E500MC /* BOOKE e500mc family */ 41 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 42 #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ 43 #define CONFIG_MP /* support multiple processors */ 44 45 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 46 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 47 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 48 #define CONFIG_PCI /* Enable PCI/PCIE */ 49 #define CONFIG_PCIE1 /* PCIE controler 1 */ 50 #define CONFIG_PCIE3 /* PCIE controler 3 */ 51 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 52 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 53 54 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 55 56 #define CONFIG_FSL_LAW /* Use common FSL init code */ 57 58 /* Environment in SPI Flash */ 59 #define CONFIG_SYS_EXTRA_ENV_RELOC 60 #define CONFIG_ENV_IS_IN_SPI_FLASH 61 #define CONFIG_ENV_SPI_BUS 0 62 #define CONFIG_ENV_SPI_CS 0 63 #define CONFIG_ENV_SPI_MAX_HZ 20000000 64 #define CONFIG_ENV_SPI_MODE 0 65 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ 66 #define CONFIG_ENV_SIZE 0x004000 /* 16K env */ 67 #define CONFIG_ENV_SECT_SIZE 0x010000 68 #define CONFIG_ENV_OFFSET_REDUND 0x110000 69 #define CONFIG_ENV_TOTAL_SIZE 0x020000 70 71 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 72 73 #ifndef __ASSEMBLY__ 74 unsigned long get_board_sys_clk(unsigned long dummy); 75 #endif 76 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 77 78 /* 79 * These can be toggled for performance analysis, otherwise use default. 80 */ 81 #define CONFIG_SYS_CACHE_STASHING 82 #define CONFIG_BACKSIDE_L2_CACHE 83 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 84 #define CONFIG_BTB /* toggle branch predition */ 85 86 #define CONFIG_ENABLE_36BIT_PHYS 87 88 #define CONFIG_ADDR_MAP 89 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 90 91 #define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */ 92 93 /* 94 * Config the L3 Cache as L3 SRAM 95 */ 96 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 97 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 98 CONFIG_RAMBOOT_TEXT_BASE) 99 #define CONFIG_SYS_L3_SIZE (1024 << 10) 100 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 101 102 #define CONFIG_SYS_DCSRBAR 0xf0000000 103 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 104 105 /* 106 * DDR Setup 107 */ 108 #define CONFIG_VERY_BIG_RAM 109 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 110 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 111 112 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 113 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 114 115 #define CONFIG_DDR_SPD 116 #define CONFIG_SYS_FSL_DDR3 117 #define CONFIG_FSL_DDR_INTERACTIVE 118 119 #define CONFIG_SYS_SPD_BUS_NUM 0 120 #define SPD_EEPROM_ADDRESS 0x54 121 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 122 123 #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 124 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 125 126 /****************************************************************************** 127 * (PRAM usage) 128 * ... ------------------------------------------------------- 129 * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM 130 * ... |<------------------- pram -------------------------->| 131 * ... ------------------------------------------------------- 132 * @END_OF_RAM: 133 * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose 134 * @CONFIG_KM_PHRAM: address for /var 135 * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) 136 * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM 137 */ 138 139 /* size of rootfs in RAM */ 140 #define CONFIG_KM_ROOTFSSIZE 0x0 141 /* pseudo-non volatile RAM [hex] */ 142 #define CONFIG_KM_PNVRAM 0x80000 143 /* physical RAM MTD size [hex] */ 144 #define CONFIG_KM_PHRAM 0x100000 145 /* reserved pram area at the end of memory [hex] 146 * u-boot reserves some memory for the MP boot page */ 147 #define CONFIG_KM_RESERVED_PRAM 0x1000 148 /* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable 149 * is not valid yet, which is the case for when u-boot copies itself to RAM */ 150 #define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10) 151 152 #define CONFIG_KM_CRAMFS_ADDR 0x2000000 153 #define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ 154 #define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ 155 156 /* 157 * Local Bus Definitions 158 */ 159 160 /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ 161 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) 162 163 /* Nand Flash */ 164 #define CONFIG_NAND_FSL_ELBC 165 #define CONFIG_SYS_NAND_BASE 0xffa00000 166 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 167 168 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 169 #define CONFIG_SYS_MAX_NAND_DEVICE 1 170 #define CONFIG_MTD_NAND_VERIFY_WRITE 171 #define CONFIG_CMD_NAND 172 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 173 174 #define CONFIG_BCH 175 176 /* NAND flash config */ 177 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 178 | BR_PS_8 /* Port Size = 8 bit */ \ 179 | BR_MS_FCM /* MSEL = FCM */ \ 180 | BR_V) /* valid */ 181 182 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ 183 | OR_FCM_BCTLD /* LBCTL not ass */ \ 184 | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ 185 | OR_FCM_RST /* 1 clk read setup */ \ 186 | OR_FCM_PGS /* Large page size */ \ 187 | OR_FCM_CST) /* 0.25 command setup */ 188 189 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 190 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 191 192 /* QRIO FPGA */ 193 #define CONFIG_SYS_QRIO_BASE 0xfb000000 194 #define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull 195 196 #define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ 197 | BR_PS_8 /* Port Size 8 bits */ \ 198 | BR_DECC_OFF /* no error corr */ \ 199 | BR_MS_GPCM /* MSEL = GPCM */ \ 200 | BR_V) /* valid */ 201 202 #define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ 203 | OR_GPCM_BCTLD /* no LCTL assert */ \ 204 | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ 205 | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ 206 | OR_GPCM_TRLX /* relaxed tmgs */ \ 207 | OR_GPCM_EAD) /* extra bus clk cycles */ 208 209 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ 210 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ 211 212 /* bootcounter in QRIO */ 213 #define CONFIG_BOOTCOUNT_LIMIT 214 #define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20) 215 216 #define CONFIG_BOARD_EARLY_INIT_F 217 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 218 #define CONFIG_MISC_INIT_F 219 #define CONFIG_MISC_INIT_R 220 #define CONFIG_LAST_STAGE_INIT 221 222 #define CONFIG_HWCONFIG 223 224 /* define to use L1 as initial stack */ 225 #define CONFIG_L1_INIT_RAM 226 #define CONFIG_SYS_INIT_RAM_LOCK 227 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 228 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 229 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 230 /* The assembler doesn't like typecast */ 231 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 232 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 233 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 234 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 235 236 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 237 GENERATED_GBL_DATA_SIZE) 238 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 239 240 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 241 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 242 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 243 244 /* Serial Port - controlled on board with jumper J8 245 * open - index 2 246 * shorted - index 1 247 */ 248 #define CONFIG_CONS_INDEX 1 249 #define CONFIG_SYS_NS16550 250 #define CONFIG_SYS_NS16550_SERIAL 251 #define CONFIG_SYS_NS16550_REG_SIZE 1 252 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 253 254 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 255 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 256 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 257 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 258 259 #define CONFIG_KM_CONSOLE_TTY "ttyS0" 260 261 /* Use the HUSH parser */ 262 #define CONFIG_SYS_HUSH_PARSER 263 264 /* pass open firmware flat tree */ 265 #define CONFIG_OF_LIBFDT 266 #define CONFIG_OF_BOARD_SETUP 267 #define CONFIG_OF_STDOUT_VIA_ALIAS 268 269 /* new uImage format support */ 270 #define CONFIG_FIT 271 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 272 273 /* I2C */ 274 275 #define CONFIG_SYS_I2C 276 #define CONFIG_SYS_I2C_INIT_BOARD 277 #define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */ 278 #define CONFIG_SYS_NUM_I2C_BUSES 3 279 #define CONFIG_SYS_I2C_MAX_HOPS 1 280 #define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ 281 #define CONFIG_I2C_MULTI_BUS 282 #define CONFIG_I2C_CMD_TREE 283 #define CONFIG_SYS_FSL_I2C_SPEED 400000 284 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 285 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 286 #define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ 287 {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ 288 {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ 289 } 290 #ifndef __ASSEMBLY__ 291 void set_sda(int state); 292 void set_scl(int state); 293 int get_sda(void); 294 int get_scl(void); 295 #endif 296 297 #define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ 298 299 /* 300 * eSPI - Enhanced SPI 301 */ 302 #define CONFIG_FSL_ESPI 303 #define CONFIG_SPI_FLASH 304 #define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ 305 #define CONFIG_SPI_FLASH_STMICRO 306 #define CONFIG_SPI_FLASH_SPANSION 307 #define CONFIG_CMD_SF 308 #define CONFIG_SF_DEFAULT_SPEED 20000000 309 #define CONFIG_SF_DEFAULT_MODE 0 310 311 /* 312 * General PCI 313 * Memory space is mapped 1-1, but I/O space must start from 0. 314 */ 315 316 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 317 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 318 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 319 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 320 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 321 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 322 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 323 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 324 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 325 326 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 327 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 328 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 329 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull 330 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 331 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 332 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 333 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull 334 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 335 336 /* Qman/Bman */ 337 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 338 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 339 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 340 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 341 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 342 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 343 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 344 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 345 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 346 347 #define CONFIG_SYS_DPAA_FMAN 348 #define CONFIG_SYS_DPAA_PME 349 /* Default address of microcode for the Linux Fman driver 350 * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) 351 * ucode is stored after env, so we got 0x120000. 352 */ 353 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 354 #define CONFIG_SYS_FMAN_FW_ADDR 0x120000 355 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 356 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 357 358 #define CONFIG_FMAN_ENET 359 #define CONFIG_PHYLIB_10G 360 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 361 362 #define CONFIG_PCI_INDIRECT_BRIDGE 363 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 364 #define CONFIG_E1000 365 366 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 367 #define CONFIG_DOS_PARTITION 368 369 /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ 370 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 371 #define CONFIG_SYS_TBIPA_VALUE 8 372 #define CONFIG_PHYLIB /* recommended PHY management */ 373 #define CONFIG_ETHPRIME "FM1@DTSEC5" 374 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 375 376 /* 377 * Environment 378 */ 379 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 380 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 381 382 /* 383 * Hardware Watchdog 384 */ 385 #define CONFIG_WATCHDOG /* enable CPU watchdog */ 386 #define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */ 387 #define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */ 388 389 390 /* 391 * additionnal command line configuration. 392 */ 393 #define CONFIG_CMD_PCI 394 #define CONFIG_CMD_NET 395 #define CONFIG_CMD_ERRATA 396 397 /* we don't need flash support */ 398 #define CONFIG_SYS_NO_FLASH 399 #undef CONFIG_CMD_IMLS 400 #undef CONFIG_CMD_FLASH 401 #undef CONFIG_FLASH_CFI_MTD 402 #undef CONFIG_JFFS2_CMDLINE 403 404 /* 405 * For booting Linux, the board info and command line data 406 * have to be in the first 64 MB of memory, since this is 407 * the maximum mapped by the Linux kernel during initialization. 408 */ 409 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 410 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 411 412 #ifdef CONFIG_CMD_KGDB 413 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 414 #endif 415 416 #define __USB_PHY_TYPE utmi 417 418 /* 419 * Environment Configuration 420 */ 421 #define CONFIG_ENV_OVERWRITE 422 #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ 423 #define CONFIG_KM_DEF_ENV "km-common=empty\0" 424 #endif 425 426 #ifndef MTDIDS_DEFAULT 427 # define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" 428 #endif /* MTDIDS_DEFAULT */ 429 430 #ifndef MTDPARTS_DEFAULT 431 # define MTDPARTS_DEFAULT "mtdparts=" \ 432 "fsl_elbc_nand:" \ 433 "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" 434 #endif /* MTDPARTS_DEFAULT */ 435 436 /* architecture specific default bootargs */ 437 #define CONFIG_KM_DEF_BOOT_ARGS_CPU "" 438 439 /* FIXME: FDT_ADDR is unspecified */ 440 #define CONFIG_KM_DEF_ENV_CPU \ 441 "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ 442 "cramfsloadfdt=" \ 443 "cramfsload ${fdt_addr_r} " \ 444 "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ 445 "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ 446 "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ 447 "update=" \ 448 "sf probe 0;sf erase 0 +${filesize};" \ 449 "sf write ${load_addr_r} 0 ${filesize};\0" \ 450 "set_fdthigh=true\0" \ 451 "" 452 453 #define CONFIG_HW_ENV_SETTINGS \ 454 "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ 455 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 456 "usb_dr_mode=host\0" 457 458 #define CONFIG_KM_NEW_ENV \ 459 "newenv=sf probe 0;" \ 460 "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ 461 __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" 462 463 /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ 464 #ifndef CONFIG_KM_DEF_ARCH 465 #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" 466 #endif 467 468 #define CONFIG_EXTRA_ENV_SETTINGS \ 469 CONFIG_KM_DEF_ENV \ 470 CONFIG_KM_DEF_ARCH \ 471 CONFIG_KM_NEW_ENV \ 472 CONFIG_HW_ENV_SETTINGS \ 473 "EEprom_ivm=pca9547:70:9\0" \ 474 "" 475 476 #endif /* _CONFIG_KMP204X_H */ 477