1 /* 2 * (C) Copyright 2013 Keymile AG 3 * Valentin Longchamp <valentin.longchamp@keymile.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef _CONFIG_KMP204X_H 9 #define _CONFIG_KMP204X_H 10 11 #define CONFIG_SYS_TEXT_BASE 0xfff40000 12 13 #define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" 14 15 /* an additionnal option is required for UBI as subpage access is 16 * supported in u-boot */ 17 #define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" 18 19 #define CONFIG_NAND_ECC_BCH 20 21 /* common KM defines */ 22 #include "keymile-common.h" 23 24 #define CONFIG_SYS_RAMBOOT 25 #define CONFIG_RAMBOOT_PBL 26 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 27 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 28 #define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg 29 #define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg 30 31 /* High Level Configuration Options */ 32 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 33 #define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ 34 #define CONFIG_MP /* support multiple processors */ 35 36 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 37 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 38 #define CONFIG_PCIE1 /* PCIE controller 1 */ 39 #define CONFIG_PCIE3 /* PCIE controller 3 */ 40 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 41 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 42 43 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 44 45 /* Environment in SPI Flash */ 46 #define CONFIG_SYS_EXTRA_ENV_RELOC 47 #define CONFIG_ENV_IS_IN_SPI_FLASH 48 #define CONFIG_ENV_SPI_BUS 0 49 #define CONFIG_ENV_SPI_CS 0 50 #define CONFIG_ENV_SPI_MAX_HZ 20000000 51 #define CONFIG_ENV_SPI_MODE 0 52 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ 53 #define CONFIG_ENV_SIZE 0x004000 /* 16K env */ 54 #define CONFIG_ENV_SECT_SIZE 0x010000 55 #define CONFIG_ENV_OFFSET_REDUND 0x110000 56 #define CONFIG_ENV_TOTAL_SIZE 0x020000 57 58 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT 59 60 #ifndef __ASSEMBLY__ 61 unsigned long get_board_sys_clk(unsigned long dummy); 62 #endif 63 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 64 65 /* 66 * These can be toggled for performance analysis, otherwise use default. 67 */ 68 #define CONFIG_SYS_CACHE_STASHING 69 #define CONFIG_BACKSIDE_L2_CACHE 70 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 71 #define CONFIG_BTB /* toggle branch predition */ 72 73 #define CONFIG_ENABLE_36BIT_PHYS 74 75 #define CONFIG_ADDR_MAP 76 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 77 78 #define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */ 79 80 /* 81 * Config the L3 Cache as L3 SRAM 82 */ 83 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 84 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 85 CONFIG_RAMBOOT_TEXT_BASE) 86 #define CONFIG_SYS_L3_SIZE (1024 << 10) 87 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 88 89 #define CONFIG_SYS_DCSRBAR 0xf0000000 90 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 91 92 /* 93 * DDR Setup 94 */ 95 #define CONFIG_VERY_BIG_RAM 96 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 97 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 98 99 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 100 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 101 102 #define CONFIG_DDR_SPD 103 #define CONFIG_FSL_DDR_INTERACTIVE 104 105 #define CONFIG_SYS_SPD_BUS_NUM 0 106 #define SPD_EEPROM_ADDRESS 0x54 107 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 108 109 #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 110 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 111 112 /****************************************************************************** 113 * (PRAM usage) 114 * ... ------------------------------------------------------- 115 * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM 116 * ... |<------------------- pram -------------------------->| 117 * ... ------------------------------------------------------- 118 * @END_OF_RAM: 119 * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose 120 * @CONFIG_KM_PHRAM: address for /var 121 * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) 122 * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM 123 */ 124 125 /* size of rootfs in RAM */ 126 #define CONFIG_KM_ROOTFSSIZE 0x0 127 /* pseudo-non volatile RAM [hex] */ 128 #define CONFIG_KM_PNVRAM 0x80000 129 /* physical RAM MTD size [hex] */ 130 #define CONFIG_KM_PHRAM 0x100000 131 /* reserved pram area at the end of memory [hex] 132 * u-boot reserves some memory for the MP boot page */ 133 #define CONFIG_KM_RESERVED_PRAM 0x1000 134 /* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable 135 * is not valid yet, which is the case for when u-boot copies itself to RAM */ 136 #define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10) 137 138 #define CONFIG_KM_CRAMFS_ADDR 0x2000000 139 #define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ 140 #define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ 141 142 /* 143 * Local Bus Definitions 144 */ 145 146 /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ 147 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) 148 149 /* Nand Flash */ 150 #define CONFIG_NAND_FSL_ELBC 151 #define CONFIG_SYS_NAND_BASE 0xffa00000 152 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 153 154 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 155 #define CONFIG_SYS_MAX_NAND_DEVICE 1 156 #define CONFIG_CMD_NAND 157 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 158 159 #define CONFIG_BCH 160 161 /* NAND flash config */ 162 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 163 | BR_PS_8 /* Port Size = 8 bit */ \ 164 | BR_MS_FCM /* MSEL = FCM */ \ 165 | BR_V) /* valid */ 166 167 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ 168 | OR_FCM_BCTLD /* LBCTL not ass */ \ 169 | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ 170 | OR_FCM_RST /* 1 clk read setup */ \ 171 | OR_FCM_PGS /* Large page size */ \ 172 | OR_FCM_CST) /* 0.25 command setup */ 173 174 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 175 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 176 177 /* QRIO FPGA */ 178 #define CONFIG_SYS_QRIO_BASE 0xfb000000 179 #define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull 180 181 #define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ 182 | BR_PS_8 /* Port Size 8 bits */ \ 183 | BR_DECC_OFF /* no error corr */ \ 184 | BR_MS_GPCM /* MSEL = GPCM */ \ 185 | BR_V) /* valid */ 186 187 #define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ 188 | OR_GPCM_BCTLD /* no LCTL assert */ \ 189 | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ 190 | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ 191 | OR_GPCM_TRLX /* relaxed tmgs */ \ 192 | OR_GPCM_EAD) /* extra bus clk cycles */ 193 194 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ 195 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ 196 197 /* bootcounter in QRIO */ 198 #define CONFIG_BOOTCOUNT_LIMIT 199 #define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_QRIO_BASE + 0x20) 200 201 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 202 #define CONFIG_MISC_INIT_F 203 #define CONFIG_MISC_INIT_R 204 #define CONFIG_LAST_STAGE_INIT 205 206 #define CONFIG_HWCONFIG 207 208 /* define to use L1 as initial stack */ 209 #define CONFIG_L1_INIT_RAM 210 #define CONFIG_SYS_INIT_RAM_LOCK 211 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 212 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 213 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 214 /* The assembler doesn't like typecast */ 215 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 216 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 217 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 218 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 219 220 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 221 GENERATED_GBL_DATA_SIZE) 222 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 223 224 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 225 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 226 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 227 228 /* Serial Port - controlled on board with jumper J8 229 * open - index 2 230 * shorted - index 1 231 */ 232 #define CONFIG_CONS_INDEX 1 233 #define CONFIG_SYS_NS16550_SERIAL 234 #define CONFIG_SYS_NS16550_REG_SIZE 1 235 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 236 237 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 238 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 239 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 240 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 241 242 #define CONFIG_KM_CONSOLE_TTY "ttyS0" 243 244 /* I2C */ 245 246 #define CONFIG_SYS_I2C 247 #define CONFIG_SYS_I2C_INIT_BOARD 248 #define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */ 249 #define CONFIG_SYS_NUM_I2C_BUSES 3 250 #define CONFIG_SYS_I2C_MAX_HOPS 1 251 #define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ 252 #define CONFIG_I2C_MULTI_BUS 253 #define CONFIG_I2C_CMD_TREE 254 #define CONFIG_SYS_FSL_I2C_SPEED 400000 255 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 256 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 257 #define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ 258 {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ 259 {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ 260 } 261 #ifndef __ASSEMBLY__ 262 void set_sda(int state); 263 void set_scl(int state); 264 int get_sda(void); 265 int get_scl(void); 266 #endif 267 268 #define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ 269 270 /* 271 * eSPI - Enhanced SPI 272 */ 273 #define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ 274 #define CONFIG_SF_DEFAULT_SPEED 20000000 275 #define CONFIG_SF_DEFAULT_MODE 0 276 277 /* 278 * General PCI 279 * Memory space is mapped 1-1, but I/O space must start from 0. 280 */ 281 282 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 283 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 284 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 285 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 286 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 287 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 288 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 289 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 290 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 291 292 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 293 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 294 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 295 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull 296 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 297 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 298 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 299 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull 300 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 301 302 /* Qman/Bman */ 303 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 304 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 305 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 306 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 307 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 308 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 309 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 310 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 311 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 312 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 313 CONFIG_SYS_BMAN_CENA_SIZE) 314 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 315 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 316 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 317 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 318 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 319 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 320 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 321 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 322 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 323 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 324 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 325 CONFIG_SYS_QMAN_CENA_SIZE) 326 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 327 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 328 329 #define CONFIG_SYS_DPAA_FMAN 330 #define CONFIG_SYS_DPAA_PME 331 /* Default address of microcode for the Linux Fman driver 332 * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) 333 * ucode is stored after env, so we got 0x120000. 334 */ 335 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 336 #define CONFIG_SYS_FMAN_FW_ADDR 0x120000 337 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 338 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 339 340 #define CONFIG_FMAN_ENET 341 #define CONFIG_PHYLIB_10G 342 #define CONFIG_PHY_MARVELL /* there is a marvell phy */ 343 344 #define CONFIG_PCI_INDIRECT_BRIDGE 345 346 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 347 348 /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ 349 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 350 #define CONFIG_SYS_TBIPA_VALUE 8 351 #define CONFIG_PHYLIB /* recommended PHY management */ 352 #define CONFIG_ETHPRIME "FM1@DTSEC5" 353 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 354 355 /* 356 * Environment 357 */ 358 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 359 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 360 361 /* 362 * Hardware Watchdog 363 */ 364 #define CONFIG_WATCHDOG /* enable CPU watchdog */ 365 #define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */ 366 #define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */ 367 368 369 /* 370 * additionnal command line configuration. 371 */ 372 #define CONFIG_CMD_PCI 373 #define CONFIG_CMD_ERRATA 374 375 /* we don't need flash support */ 376 #define CONFIG_SYS_NO_FLASH 377 #undef CONFIG_FLASH_CFI_MTD 378 #undef CONFIG_JFFS2_CMDLINE 379 380 /* 381 * For booting Linux, the board info and command line data 382 * have to be in the first 64 MB of memory, since this is 383 * the maximum mapped by the Linux kernel during initialization. 384 */ 385 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 386 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 387 388 #ifdef CONFIG_CMD_KGDB 389 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 390 #endif 391 392 #define __USB_PHY_TYPE utmi 393 #define CONFIG_USB_EHCI_FSL 394 395 /* 396 * Environment Configuration 397 */ 398 #define CONFIG_ENV_OVERWRITE 399 #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ 400 #define CONFIG_KM_DEF_ENV "km-common=empty\0" 401 #endif 402 403 #ifndef MTDIDS_DEFAULT 404 # define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" 405 #endif /* MTDIDS_DEFAULT */ 406 407 #ifndef MTDPARTS_DEFAULT 408 # define MTDPARTS_DEFAULT "mtdparts=" \ 409 "fsl_elbc_nand:" \ 410 "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" 411 #endif /* MTDPARTS_DEFAULT */ 412 413 /* architecture specific default bootargs */ 414 #define CONFIG_KM_DEF_BOOT_ARGS_CPU "" 415 416 /* FIXME: FDT_ADDR is unspecified */ 417 #define CONFIG_KM_DEF_ENV_CPU \ 418 "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ 419 "cramfsloadfdt=" \ 420 "cramfsload ${fdt_addr_r} " \ 421 "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ 422 "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ 423 "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ 424 "update=" \ 425 "sf probe 0;sf erase 0 +${filesize};" \ 426 "sf write ${load_addr_r} 0 ${filesize};\0" \ 427 "set_fdthigh=true\0" \ 428 "checkfdt=true\0" \ 429 "" 430 431 #define CONFIG_HW_ENV_SETTINGS \ 432 "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ 433 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 434 "usb_dr_mode=host\0" 435 436 #define CONFIG_KM_NEW_ENV \ 437 "newenv=sf probe 0;" \ 438 "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ 439 __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" 440 441 /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ 442 #ifndef CONFIG_KM_DEF_ARCH 443 #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" 444 #endif 445 446 #define CONFIG_EXTRA_ENV_SETTINGS \ 447 CONFIG_KM_DEF_ENV \ 448 CONFIG_KM_DEF_ARCH \ 449 CONFIG_KM_NEW_ENV \ 450 CONFIG_HW_ENV_SETTINGS \ 451 "EEprom_ivm=pca9547:70:9\0" \ 452 "" 453 454 #endif /* _CONFIG_KMP204X_H */ 455