1 /*
2  * (C) Copyright 2013 Keymile AG
3  * Valentin Longchamp <valentin.longchamp@keymile.com>
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 #ifndef _CONFIG_KMP204X_H
9 #define _CONFIG_KMP204X_H
10 
11 #define CONFIG_PHYS_64BIT
12 #define CONFIG_PPC_P2041
13 
14 #define CONFIG_SYS_TEXT_BASE	0xfff40000
15 
16 #define CONFIG_KM_DEF_NETDEV	"netdev=eth0\0"
17 
18 /* an additionnal option is required for UBI as subpage access is
19  * supported in u-boot */
20 #define CONFIG_KM_UBI_PART_BOOT_OPTS		",2048"
21 
22 #define CONFIG_NAND_ECC_BCH
23 
24 #define CONFIG_SYS_GENERIC_BOARD
25 #define CONFIG_DISPLAY_BOARDINFO
26 
27 /* common KM defines */
28 #include "keymile-common.h"
29 
30 #define CONFIG_SYS_RAMBOOT
31 #define CONFIG_RAMBOOT_PBL
32 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
33 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
34 #define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
35 #define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
36 
37 /* High Level Configuration Options */
38 #define CONFIG_BOOKE
39 #define CONFIG_E500			/* BOOKE e500 family */
40 #define CONFIG_E500MC			/* BOOKE e500mc family */
41 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
42 #define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
43 #define CONFIG_MP			/* support multiple processors */
44 
45 #define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
46 #define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
47 #define CONFIG_FSL_ELBC			/* Has Enhanced localbus controller */
48 #define CONFIG_PCI			/* Enable PCI/PCIE */
49 #define CONFIG_PCIE1			/* PCIE controler 1 */
50 #define CONFIG_PCIE3			/* PCIE controler 3 */
51 #define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
52 #define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
53 
54 #define CONFIG_SYS_DPAA_RMAN		/* RMan */
55 
56 #define CONFIG_FSL_LAW			/* Use common FSL init code */
57 
58 /* Environment in SPI Flash */
59 #define CONFIG_SYS_EXTRA_ENV_RELOC
60 #define CONFIG_ENV_IS_IN_SPI_FLASH
61 #define CONFIG_ENV_SPI_BUS              0
62 #define CONFIG_ENV_SPI_CS               0
63 #define CONFIG_ENV_SPI_MAX_HZ           20000000
64 #define CONFIG_ENV_SPI_MODE             0
65 #define CONFIG_ENV_OFFSET               0x100000	/* 1MB for u-boot */
66 #define CONFIG_ENV_SIZE			0x004000	/* 16K env */
67 #define CONFIG_ENV_SECT_SIZE            0x010000
68 #define CONFIG_ENV_OFFSET_REDUND	0x110000
69 #define CONFIG_ENV_TOTAL_SIZE		0x020000
70 
71 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
72 
73 #ifndef __ASSEMBLY__
74 unsigned long get_board_sys_clk(unsigned long dummy);
75 #endif
76 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
77 
78 /*
79  * These can be toggled for performance analysis, otherwise use default.
80  */
81 #define CONFIG_SYS_CACHE_STASHING
82 #define CONFIG_BACKSIDE_L2_CACHE
83 #define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
84 #define CONFIG_BTB			/* toggle branch predition */
85 
86 #define CONFIG_ENABLE_36BIT_PHYS
87 
88 #define CONFIG_ADDR_MAP
89 #define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
90 
91 #define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS	/* POST memory regions test */
92 
93 /*
94  *  Config the L3 Cache as L3 SRAM
95  */
96 #define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
97 #define CONFIG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | \
98 		CONFIG_RAMBOOT_TEXT_BASE)
99 #define CONFIG_SYS_L3_SIZE		(1024 << 10)
100 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
101 
102 #define CONFIG_SYS_DCSRBAR		0xf0000000
103 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
104 
105 /*
106  * DDR Setup
107  */
108 #define CONFIG_VERY_BIG_RAM
109 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
110 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
111 
112 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
113 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
114 
115 #define CONFIG_DDR_SPD
116 #define CONFIG_SYS_FSL_DDR3
117 #define CONFIG_FSL_DDR_INTERACTIVE
118 
119 #define CONFIG_SYS_SPD_BUS_NUM	0
120 #define SPD_EEPROM_ADDRESS	0x54
121 #define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
122 
123 #define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
124 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
125 
126 /******************************************************************************
127  * (PRAM usage)
128  * ... -------------------------------------------------------
129  * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
130  * ... |<------------------- pram -------------------------->|
131  * ... -------------------------------------------------------
132  * @END_OF_RAM:
133  * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
134  * @CONFIG_KM_PHRAM: address for /var
135  * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
136  * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
137  */
138 
139 /* size of rootfs in RAM */
140 #define CONFIG_KM_ROOTFSSIZE	0x0
141 /* pseudo-non volatile RAM [hex] */
142 #define CONFIG_KM_PNVRAM	0x80000
143 /* physical RAM MTD size [hex] */
144 #define CONFIG_KM_PHRAM		0x100000
145 /* reserved pram area at the end of memory [hex]
146  * u-boot reserves some memory for the MP boot page */
147 #define CONFIG_KM_RESERVED_PRAM	0x1000
148 /* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
149  * is not valid yet, which is the case for when u-boot copies itself to RAM */
150 #define CONFIG_PRAM		((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10)
151 
152 #define CONFIG_KM_CRAMFS_ADDR	0x2000000
153 #define CONFIG_KM_KERNEL_ADDR	0x1000000	/* max kernel size 15.5Mbytes */
154 #define CONFIG_KM_FDT_ADDR	0x1F80000	/* max dtb    size  0.5Mbytes */
155 
156 /*
157  * Local Bus Definitions
158  */
159 
160 /* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
161 #define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_8 | LCRR_EADC_2)
162 
163 /* Nand Flash */
164 #define CONFIG_NAND_FSL_ELBC
165 #define CONFIG_SYS_NAND_BASE		0xffa00000
166 #define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
167 
168 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
169 #define CONFIG_SYS_MAX_NAND_DEVICE	1
170 #define CONFIG_MTD_NAND_VERIFY_WRITE
171 #define CONFIG_CMD_NAND
172 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
173 
174 #define CONFIG_BCH
175 
176 /* NAND flash config */
177 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
178 			       | BR_PS_8	       /* Port Size = 8 bit */ \
179 			       | BR_MS_FCM	       /* MSEL = FCM */ \
180 			       | BR_V)		       /* valid */
181 
182 #define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB	      /* length 256K */ \
183 			       | OR_FCM_BCTLD	/* LBCTL not ass */	\
184 			       | OR_FCM_SCY_1	/* 1 clk wait cycle */	\
185 			       | OR_FCM_RST	/* 1 clk read setup */	\
186 			       | OR_FCM_PGS	/* Large page size */	\
187 			       | OR_FCM_CST)	/* 0.25 command setup */
188 
189 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
190 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
191 
192 /* QRIO FPGA */
193 #define CONFIG_SYS_QRIO_BASE		0xfb000000
194 #define CONFIG_SYS_QRIO_BASE_PHYS	0xffb000000ull
195 
196 #define CONFIG_SYS_QRIO_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
197 				| BR_PS_8	/* Port Size 8 bits */ \
198 				| BR_DECC_OFF	/* no error corr */ \
199 				| BR_MS_GPCM	/* MSEL = GPCM */ \
200 				| BR_V)		/* valid */
201 
202 #define CONFIG_SYS_QRIO_OR_PRELIM  (OR_AM_64KB	/* length 64K */ \
203 				| OR_GPCM_BCTLD /* no LCTL assert */ \
204 				| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
205 				| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
206 				| OR_GPCM_TRLX /* relaxed tmgs */ \
207 				| OR_GPCM_EAD) /* extra bus clk cycles */
208 
209 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
210 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
211 
212 /* bootcounter in QRIO */
213 #define CONFIG_BOOTCOUNT_LIMIT
214 #define CONFIG_SYS_BOOTCOUNT_ADDR	(CONFIG_SYS_QRIO_BASE + 0x20)
215 
216 #define CONFIG_BOARD_EARLY_INIT_F
217 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
218 #define CONFIG_MISC_INIT_F
219 #define CONFIG_MISC_INIT_R
220 #define CONFIG_LAST_STAGE_INIT
221 
222 #define CONFIG_HWCONFIG
223 
224 /* define to use L1 as initial stack */
225 #define CONFIG_L1_INIT_RAM
226 #define CONFIG_SYS_INIT_RAM_LOCK
227 #define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
228 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
229 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
230 /* The assembler doesn't like typecast */
231 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
232 	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
233 	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
234 #define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
235 
236 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
237 					GENERATED_GBL_DATA_SIZE)
238 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
239 
240 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
241 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
242 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)
243 
244 /* Serial Port - controlled on board with jumper J8
245  * open - index 2
246  * shorted - index 1
247  */
248 #define CONFIG_CONS_INDEX	1
249 #define CONFIG_SYS_NS16550
250 #define CONFIG_SYS_NS16550_SERIAL
251 #define CONFIG_SYS_NS16550_REG_SIZE	1
252 #define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
253 
254 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
255 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
256 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
257 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
258 
259 #define CONFIG_KM_CONSOLE_TTY	"ttyS0"
260 
261 /* Use the HUSH parser */
262 #define CONFIG_SYS_HUSH_PARSER
263 
264 /* pass open firmware flat tree */
265 #define CONFIG_OF_LIBFDT
266 #define CONFIG_OF_BOARD_SETUP
267 #define CONFIG_OF_STDOUT_VIA_ALIAS
268 
269 /* new uImage format support */
270 #define CONFIG_FIT
271 #define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
272 
273 /* I2C */
274 
275 #define CONFIG_SYS_I2C
276 #define CONFIG_SYS_I2C_INIT_BOARD
277 #define CONFIG_SYS_I2C_SPEED		100000 /* deblocking */
278 #define CONFIG_SYS_NUM_I2C_BUSES	3
279 #define CONFIG_SYS_I2C_MAX_HOPS		1
280 #define CONFIG_SYS_I2C_FSL		/* Use FSL I2C driver */
281 #define CONFIG_I2C_MULTI_BUS
282 #define CONFIG_I2C_CMD_TREE
283 #define CONFIG_SYS_FSL_I2C_SPEED	400000
284 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
285 #define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
286 #define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
287 					{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
288 					{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
289 				}
290 #ifndef __ASSEMBLY__
291 void set_sda(int state);
292 void set_scl(int state);
293 int get_sda(void);
294 int get_scl(void);
295 #endif
296 
297 #define CONFIG_KM_IVM_BUS		1	/* I2C1 (Mux-Port 1)*/
298 
299 /*
300  * eSPI - Enhanced SPI
301  */
302 #define CONFIG_FSL_ESPI
303 #define CONFIG_SPI_FLASH
304 #define CONFIG_SPI_FLASH_BAR	/* 4 byte-addressing */
305 #define CONFIG_SPI_FLASH_STMICRO
306 #define CONFIG_SPI_FLASH_SPANSION
307 #define CONFIG_CMD_SF
308 #define CONFIG_SF_DEFAULT_SPEED         20000000
309 #define CONFIG_SF_DEFAULT_MODE          0
310 
311 /*
312  * General PCI
313  * Memory space is mapped 1-1, but I/O space must start from 0.
314  */
315 
316 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
317 #define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
318 #define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
319 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
320 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
321 #define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
322 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
323 #define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
324 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
325 
326 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
327 #define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
328 #define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
329 #define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
330 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
331 #define CONFIG_SYS_PCIE3_IO_VIRT	0xf8010000
332 #define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
333 #define CONFIG_SYS_PCIE3_IO_PHYS	0xff8010000ull
334 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
335 
336 /* Qman/Bman */
337 #define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
338 #define CONFIG_SYS_BMAN_NUM_PORTALS	10
339 #define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
340 #define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
341 #define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
342 #define CONFIG_SYS_QMAN_NUM_PORTALS	10
343 #define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
344 #define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
345 #define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
346 
347 #define CONFIG_SYS_DPAA_FMAN
348 #define CONFIG_SYS_DPAA_PME
349 /* Default address of microcode for the Linux Fman driver
350  * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
351  * ucode is stored after env, so we got 0x120000.
352  */
353 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
354 #define CONFIG_SYS_FMAN_FW_ADDR	0x120000
355 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
356 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
357 
358 #define CONFIG_FMAN_ENET
359 #define CONFIG_PHYLIB_10G
360 #define CONFIG_PHY_MARVELL		/* there is a marvell phy */
361 
362 #define CONFIG_PCI_INDIRECT_BRIDGE
363 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
364 #define CONFIG_E1000
365 
366 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
367 #define CONFIG_DOS_PARTITION
368 
369 /* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */
370 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR	0x11
371 #define CONFIG_SYS_TBIPA_VALUE	8
372 #define CONFIG_PHYLIB		/* recommended PHY management */
373 #define CONFIG_ETHPRIME		"FM1@DTSEC5"
374 #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
375 
376 /*
377  * Environment
378  */
379 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
380 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
381 
382 /*
383  * Hardware Watchdog
384  */
385 #define CONFIG_WATCHDOG			/* enable CPU watchdog */
386 #define CONFIG_WATCHDOG_PRESC 34	/* wdog prescaler 2^(64-34) (~10min) */
387 #define CONFIG_WATCHDOG_RC WRC_CHIP	/* reset chip on watchdog event */
388 
389 
390 /*
391  * additionnal command line configuration.
392  */
393 #define CONFIG_CMD_PCI
394 #define CONFIG_CMD_NET
395 #define CONFIG_CMD_ERRATA
396 
397 /* we don't need flash support */
398 #define CONFIG_SYS_NO_FLASH
399 #undef CONFIG_CMD_IMLS
400 #undef CONFIG_CMD_FLASH
401 #undef CONFIG_FLASH_CFI_MTD
402 #undef CONFIG_JFFS2_CMDLINE
403 
404 /*
405  * For booting Linux, the board info and command line data
406  * have to be in the first 64 MB of memory, since this is
407  * the maximum mapped by the Linux kernel during initialization.
408  */
409 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux */
410 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
411 
412 #ifdef CONFIG_CMD_KGDB
413 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
414 #endif
415 
416 #define __USB_PHY_TYPE	utmi
417 
418 /*
419  * Environment Configuration
420  */
421 #define CONFIG_ENV_OVERWRITE
422 #ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
423 #define CONFIG_KM_DEF_ENV "km-common=empty\0"
424 #endif
425 
426 #ifndef MTDIDS_DEFAULT
427 # define MTDIDS_DEFAULT		"nand0=fsl_elbc_nand"
428 #endif /* MTDIDS_DEFAULT */
429 
430 #ifndef MTDPARTS_DEFAULT
431 # define MTDPARTS_DEFAULT	"mtdparts="			\
432 	"fsl_elbc_nand:"						\
433 		"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
434 #endif /* MTDPARTS_DEFAULT */
435 
436 /* architecture specific default bootargs */
437 #define CONFIG_KM_DEF_BOOT_ARGS_CPU		""
438 
439 /* FIXME: FDT_ADDR is unspecified */
440 #define CONFIG_KM_DEF_ENV_CPU						\
441 	"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0"			\
442 	"cramfsloadfdt="						\
443 		"cramfsload ${fdt_addr_r} "				\
444 		"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0"		\
445 	"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0"		\
446 	"u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0"		\
447 	"update="							\
448 		"sf probe 0;sf erase 0 +${filesize};"			\
449 		"sf write ${load_addr_r} 0 ${filesize};\0"		\
450 	"set_fdthigh=true\0"						\
451 	""
452 
453 #define CONFIG_HW_ENV_SETTINGS						\
454 	"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0"			\
455 	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"		\
456 	"usb_dr_mode=host\0"
457 
458 #define CONFIG_KM_NEW_ENV						\
459 	"newenv=sf probe 0;"						\
460 		"sf erase " __stringify(CONFIG_ENV_OFFSET) " "		\
461 		__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
462 
463 /* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
464 #ifndef CONFIG_KM_DEF_ARCH
465 #define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
466 #endif
467 
468 #define CONFIG_EXTRA_ENV_SETTINGS					\
469 	CONFIG_KM_DEF_ENV						\
470 	CONFIG_KM_DEF_ARCH						\
471 	CONFIG_KM_NEW_ENV						\
472 	CONFIG_HW_ENV_SETTINGS						\
473 	"EEprom_ivm=pca9547:70:9\0"					\
474 	""
475 
476 #endif /* _CONFIG_KMP204X_H */
477