1 /* 2 * (C) Copyright 2011 3 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __CONFIG_KEYMILE_POWERPC_H 9 #define __CONFIG_KEYMILE_POWERPC_H 10 11 /* Do boardspecific init for all boards */ 12 #define CONFIG_BOARD_EARLY_INIT_R 13 #define CONFIG_LAST_STAGE_INIT 14 15 #define CONFIG_BOOTCOUNT_LIMIT 16 17 #define CONFIG_CMD_DTT 18 #define CONFIG_JFFS2_CMDLINE 19 20 /* Pass open firmware flat tree */ 21 #define CONFIG_OF_LIBFDT 22 #define CONFIG_OF_BOARD_SETUP 23 24 /* standard km ethernet_present for piggy */ 25 #define CONFIG_KM_COMMON_ETH_INIT 26 27 /* EEprom support 24C08, 24C16, 24C64 */ 28 #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE 29 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* 8 Byte write page */ 30 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 31 32 #define CONFIG_ENV_SIZE 0x04000 /* Size of Environment */ 33 #define CONFIG_FLASH_CFI_MTD 34 35 #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ 36 37 #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ 38 39 #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ 40 41 /* Reserve 4 MB for malloc */ 42 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 43 44 /****************************************************************************** 45 * (PRAM usage) 46 * ... ------------------------------------------------------- 47 * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM 48 * ... |<------------------- pram -------------------------->| 49 * ... ------------------------------------------------------- 50 * @END_OF_RAM: 51 * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose 52 * @CONFIG_KM_PHRAM: address for /var 53 * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) 54 * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM 55 */ 56 57 /* size of rootfs in RAM */ 58 #define CONFIG_KM_ROOTFSSIZE 0x0 59 /* pseudo-non volatile RAM [hex] */ 60 #define CONFIG_KM_PNVRAM 0x80000 61 /* physical RAM MTD size [hex] */ 62 #define CONFIG_KM_PHRAM 0x100000 63 /* resereved pram area at the end of memroy [hex] */ 64 #define CONFIG_KM_RESERVED_PRAM 0x0 65 /* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable 66 * is not valid yet, which is the case for when u-boot copies itself to RAM */ 67 #define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM)>>10) 68 69 #define CONFIG_KM_CRAMFS_ADDR 0xC00000 70 #define CONFIG_KM_KERNEL_ADDR 0x400000 /* 7680Kbytes */ 71 #define CONFIG_KM_FDT_ADDR 0xB80000 /* 512Kbytes */ 72 73 /* architecture specific default bootargs */ 74 #define CONFIG_KM_DEF_BOOT_ARGS_CPU "" 75 76 #define CONFIG_KM_DEF_ENV_CPU \ 77 "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.bin\0" \ 78 "update=" \ 79 "protect off " __stringify(BOOTFLASH_START) " +${filesize} && "\ 80 "erase " __stringify(BOOTFLASH_START) " +${filesize} && "\ 81 "cp.b ${load_addr_r} " __stringify(BOOTFLASH_START) \ 82 " ${filesize} && " \ 83 "protect on " __stringify(BOOTFLASH_START) " +${filesize}\0"\ 84 "set_fdthigh=true\0" \ 85 "checkfdt=true\0" \ 86 "" 87 88 #endif /* __CONFIG_KEYMILE_POWERPC_H */ 89