xref: /openbmc/u-boot/include/configs/ids8313.h (revision fcf2fba4)
1 /*
2  * (C) Copyright 2013
3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
4  *
5  * Based on:
6  * Copyright (c) 2011 IDS GmbH, Germany
7  * Sergej Stepanov <ste@ids.de>
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #ifndef __CONFIG_H
13 #define __CONFIG_H
14 
15 /*
16  * High Level Configuration Options
17  */
18 #define CONFIG_MPC831x
19 #define CONFIG_MPC8313
20 #define CONFIG_IDS8313
21 
22 #define CONFIG_FSL_ELBC
23 
24 #define CONFIG_MISC_INIT_R
25 
26 #define CONFIG_BOOT_RETRY_TIME		900
27 #define CONFIG_BOOT_RETRY_MIN		30
28 #define CONFIG_RESET_TO_RETRY
29 
30 #define CONFIG_83XX_CLKIN		66000000	/* in Hz */
31 #define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
32 
33 #define CONFIG_SYS_IMMR		0xF0000000
34 
35 #define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
36 #define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
37 
38 /*
39  * Hardware Reset Configuration Word
40  * if CLKIN is 66.000MHz, then
41  * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
42  */
43 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
44 			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
45 			     HRCWL_CSB_TO_CLKIN_2X1 |\
46 			     HRCWL_CORE_TO_CSB_2X1)
47 
48 #define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
49 				 HRCWH_CORE_ENABLE |\
50 				 HRCWH_FROM_0XFFF00100 |\
51 				 HRCWH_BOOTSEQ_DISABLE |\
52 				 HRCWH_SW_WATCHDOG_DISABLE |\
53 				 HRCWH_ROM_LOC_LOCAL_8BIT |\
54 				 HRCWH_RL_EXT_LEGACY |\
55 				 HRCWH_TSEC1M_IN_MII |\
56 				 HRCWH_TSEC2M_IN_MII |\
57 				 HRCWH_BIG_ENDIAN)
58 
59 #define CONFIG_SYS_SICRH	0x00000000
60 #define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
61 
62 #define CONFIG_HWCONFIG
63 
64 #define CONFIG_SYS_HID0_INIT	0x000000000
65 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
66 				 HID0_ENABLE_INSTRUCTION_CACHE |\
67 				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
68 
69 #define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
70 
71 /*
72  * Definitions for initial stack pointer and data area (in DCACHE )
73  */
74 #define CONFIG_SYS_INIT_RAM_LOCK
75 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
76 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
77 #define CONFIG_SYS_GBL_DATA_SIZE	0x100
78 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
79 					 - CONFIG_SYS_GBL_DATA_SIZE)
80 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
81 
82 /*
83  * Local Bus LCRR and LBCR regs
84  */
85 #define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
86 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
87 #define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
88 					 (0xFF << LBCR_BMT_SHIFT) |\
89 					 0xF)
90 
91 #define CONFIG_SYS_LBC_MRTPR		0x20000000
92 
93 /*
94  * Internal Definitions
95  */
96 /*
97  * DDR Setup
98  */
99 #define CONFIG_SYS_DDR_BASE		0x00000000
100 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
101 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
102 
103 /*
104  * Manually set up DDR parameters,
105  * as this board has not the SPD connected to I2C.
106  */
107 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
108 #define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
109 					 0x00010000 |\
110 					 CSCONFIG_ROW_BIT_13 |\
111 					 CSCONFIG_COL_BIT_10)
112 
113 #define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
114 					 CSCONFIG_BANK_BIT_3)
115 
116 #define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
117 #define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
118 				(3 << TIMING_CFG0_WRT_SHIFT) |\
119 				(3 << TIMING_CFG0_RRT_SHIFT) |\
120 				(3 << TIMING_CFG0_WWT_SHIFT) |\
121 				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
122 				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
123 				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
124 				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
125 #define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
126 				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
127 				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
128 				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
129 				(4 << TIMING_CFG1_REFREC_SHIFT) |\
130 				(4 << TIMING_CFG1_WRREC_SHIFT) |\
131 				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
132 				(2 << TIMING_CFG1_WRTORD_SHIFT))
133 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
134 				(5 << TIMING_CFG2_CPO_SHIFT) |\
135 				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
136 				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
137 				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
138 				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
139 				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
140 
141 #define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
142 				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
143 
144 #define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
145 					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
146 					 SDRAM_CFG_DBW_32 |\
147 					 SDRAM_CFG_SDRAM_TYPE_DDR2)
148 
149 #define CONFIG_SYS_SDRAM_CFG2		0x00401000
150 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
151 					 (0x0242 << SDRAM_MODE_SD_SHIFT))
152 #define CONFIG_SYS_DDR_MODE_2		0x00000000
153 #define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
154 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
155 					 DDRCDR_PZ_NOMZ |\
156 					 DDRCDR_NZ_NOMZ |\
157 					 DDRCDR_ODT |\
158 					 DDRCDR_M_ODR |\
159 					 DDRCDR_Q_DRN)
160 
161 /*
162  * on-board devices
163  */
164 #define CONFIG_TSEC1
165 #define CONFIG_TSEC2
166 #define CONFIG_TSEC_ENET
167 #define CONFIG_HARD_SPI
168 
169 /*
170  * NOR FLASH setup
171  */
172 #define CONFIG_SYS_FLASH_CFI
173 #define CONFIG_FLASH_CFI_DRIVER
174 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
175 #define CONFIG_FLASH_SHOW_PROGRESS	50
176 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
177 
178 #define CONFIG_SYS_FLASH_BASE		0xFF800000
179 #define CONFIG_SYS_FLASH_SIZE		8
180 #define CONFIG_SYS_FLASH_PROTECTION
181 
182 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
183 #define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
184 
185 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
186 					 BR_PS_8 |\
187 					 BR_MS_GPCM |\
188 					 BR_V)
189 
190 #define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
191 					 OR_GPCM_SCY_10 |\
192 					 OR_GPCM_EHTR |\
193 					 OR_GPCM_TRLX |\
194 					 OR_GPCM_CSNT |\
195 					 OR_GPCM_EAD)
196 #define CONFIG_SYS_MAX_FLASH_BANKS	1
197 #define CONFIG_SYS_MAX_FLASH_SECT	128
198 
199 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000
200 #define CONFIG_SYS_FLASH_WRITE_TOUT	500
201 
202 /*
203  * NAND FLASH setup
204  */
205 #define CONFIG_SYS_NAND_BASE		0xE1000000
206 #define CONFIG_SYS_MAX_NAND_DEVICE	1
207 #define CONFIG_SYS_NAND_MAX_CHIPS	1
208 #define CONFIG_NAND_FSL_ELBC
209 #define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
210 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
211 #define NAND_CACHE_PAGES		64
212 
213 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
214 #define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
215 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
216 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
217 
218 #define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
219 				 (2<<BR_DECC_SHIFT) |\
220 				 BR_PS_8 |\
221 				 BR_MS_FCM |\
222 				 BR_V)
223 
224 #define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
225 				 OR_FCM_PGS |\
226 				 OR_FCM_CSCT |\
227 				 OR_FCM_CST |\
228 				 OR_FCM_CHT |\
229 				 OR_FCM_SCY_4 |\
230 				 OR_FCM_TRLX |\
231 				 OR_FCM_EHTR |\
232 				 OR_FCM_RST)
233 
234 /*
235  * MRAM setup
236  */
237 #define CONFIG_SYS_MRAM_BASE		0xE2000000
238 #define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
239 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
240 #define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
241 
242 #define CONFIG_SYS_OR_TIMING_MRAM
243 
244 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
245 					 BR_PS_8 |\
246 					 BR_MS_GPCM |\
247 					 BR_V)
248 
249 #define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
250 
251 /*
252  * CPLD setup
253  */
254 #define CONFIG_SYS_CPLD_BASE		0xE3000000
255 #define CONFIG_SYS_CPLD_SIZE		0x8000
256 #define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
257 #define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
258 
259 #define CONFIG_SYS_OR_TIMING_MRAM
260 
261 #define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
262 					 BR_PS_8 |\
263 					 BR_MS_GPCM |\
264 					 BR_V)
265 
266 #define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
267 
268 /*
269  * HW-Watchdog
270  */
271 #define CONFIG_WATCHDOG		1
272 #define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
273 
274 /*
275  * I2C setup
276  */
277 #define CONFIG_SYS_I2C
278 #define CONFIG_SYS_I2C_FSL
279 #define CONFIG_SYS_FSL_I2C_SPEED	400000
280 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
281 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
282 #define CONFIG_RTC_PCF8563
283 #define CONFIG_SYS_I2C_RTC_ADDR	0x51
284 
285 /*
286  * SPI setup
287  */
288 #ifdef CONFIG_HARD_SPI
289 #define CONFIG_MPC8XXX_SPI
290 #define CONFIG_SYS_GPIO1_PRELIM
291 #define CONFIG_SYS_GPIO1_DIR		0x00000001
292 #define CONFIG_SYS_GPIO1_DAT		0x00000001
293 #endif
294 
295 /*
296  * Ethernet setup
297  */
298 #ifdef CONFIG_TSEC1
299 #define CONFIG_HAS_ETH0
300 #define CONFIG_TSEC1_NAME		"TSEC0"
301 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
302 #define TSEC1_PHY_ADDR			0x1
303 #define TSEC1_FLAGS			TSEC_GIGABIT
304 #define TSEC1_PHYIDX			0
305 #endif
306 
307 #ifdef CONFIG_TSEC2
308 #define CONFIG_HAS_ETH1
309 #define CONFIG_TSEC2_NAME		"TSEC1"
310 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
311 #define TSEC2_PHY_ADDR			0x3
312 #define TSEC2_FLAGS			TSEC_GIGABIT
313 #define TSEC2_PHYIDX			0
314 #endif
315 #define CONFIG_ETHPRIME		"TSEC1"
316 
317 /*
318  * Serial Port
319  */
320 #define CONFIG_CONS_INDEX		1
321 #define CONFIG_SYS_NS16550_SERIAL
322 #define CONFIG_SYS_NS16550_REG_SIZE	1
323 
324 #define CONFIG_SYS_BAUDRATE_TABLE	\
325 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
326 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
327 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
328 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
329 
330 #define CONFIG_HAS_FSL_DR_USB
331 #define CONFIG_SYS_SCCR_USBDRCM	3
332 
333 /*
334  * BAT's
335  */
336 #define CONFIG_HIGH_BATS
337 
338 /* DDR @ 0x00000000 */
339 #define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
340 					 BATL_PP_10)
341 #define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
342 					 BATU_BL_256M |\
343 					 BATU_VS |\
344 					 BATU_VP)
345 #define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
346 #define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
347 
348 /* Initial RAM @ 0xFD000000 */
349 #define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
350 					 BATL_PP_10 |\
351 					 BATL_GUARDEDSTORAGE)
352 #define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
353 					 BATU_BL_256K |\
354 					 BATU_VS |\
355 					 BATU_VP)
356 #define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
357 #define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
358 
359 /* FLASH @ 0xFF800000 */
360 #define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
361 					 BATL_PP_10 |\
362 					 BATL_GUARDEDSTORAGE)
363 #define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
364 					 BATU_BL_8M |\
365 					 BATU_VS |\
366 					 BATU_VP)
367 #define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
368 					 BATL_PP_10 |\
369 					 BATL_CACHEINHIBIT |\
370 					 BATL_GUARDEDSTORAGE)
371 #define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
372 
373 #define CONFIG_SYS_IBAT3L		(0)
374 #define CONFIG_SYS_IBAT3U		(0)
375 #define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
376 #define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
377 
378 #define CONFIG_SYS_IBAT4L		(0)
379 #define CONFIG_SYS_IBAT4U		(0)
380 #define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
381 #define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
382 
383 /* IMMRBAR @ 0xF0000000 */
384 #define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
385 					 BATL_PP_10 |\
386 					 BATL_CACHEINHIBIT |\
387 					 BATL_GUARDEDSTORAGE)
388 #define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
389 					 BATU_BL_128M |\
390 					 BATU_VS |\
391 					 BATU_VP)
392 #define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
393 #define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
394 
395 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
396 #define CONFIG_SYS_IBAT6L		(0xE0000000 |\
397 					 BATL_PP_10 |\
398 					 BATL_GUARDEDSTORAGE)
399 #define CONFIG_SYS_IBAT6U		(0xE0000000 |\
400 					 BATU_BL_256M |\
401 					 BATU_VS |\
402 					 BATU_VP)
403 #define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
404 #define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
405 
406 #define CONFIG_SYS_IBAT7L		(0)
407 #define CONFIG_SYS_IBAT7U		(0)
408 #define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
409 #define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
410 
411 /*
412  * U-Boot environment setup
413  */
414 #define CONFIG_CMD_NAND
415 #define CONFIG_CMDLINE_EDITING
416 #define CONFIG_CMD_JFFS2
417 #define CONFIG_BOOTP_SUBNETMASK
418 #define CONFIG_BOOTP_GATEWAY
419 #define CONFIG_BOOTP_HOSTNAME
420 #define CONFIG_BOOTP_BOOTPATH
421 #define CONFIG_BOOTP_BOOTFILESIZE
422 
423 /*
424  * The reserved memory
425  */
426 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
427 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
428 #define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
429 
430 /*
431  * Environment Configuration
432  */
433 #define CONFIG_ENV_IS_IN_FLASH
434 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
435 				+ CONFIG_SYS_MONITOR_LEN)
436 #define CONFIG_ENV_SIZE		0x20000
437 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
438 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
439 
440 #define CONFIG_NETDEV			eth1
441 #define CONFIG_HOSTNAME		ids8313
442 #define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
443 #define CONFIG_BOOTFILE		"ids8313/uImage"
444 #define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
445 #define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
446 #define CONFIG_LOADADDR		0x400000
447 #define CONFIG_CMD_ENV_FLAGS
448 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
449 
450 /* Initial Memory map for Linux*/
451 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
452 
453 /*
454  * Miscellaneous configurable options
455  */
456 #define CONFIG_SYS_LONGHELP
457 #define CONFIG_SYS_CBSIZE		1024
458 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
459 					 + sizeof(CONFIG_SYS_PROMPT)+16)
460 #define CONFIG_SYS_MAXARGS		16
461 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
462 
463 #define CONFIG_SYS_MEMTEST_START	0x00001000
464 #define CONFIG_SYS_MEMTEST_END		0x00C00000
465 
466 #define CONFIG_SYS_LOAD_ADDR		0x100000
467 #define CONFIG_MII
468 #define CONFIG_LOADS_ECHO
469 #define CONFIG_TIMESTAMP
470 #define CONFIG_PREBOOT			"echo;" \
471 					"echo Type \\\"run nfsboot\\\" " \
472 					"to mount root filesystem over NFS;echo"
473 #undef	CONFIG_BOOTARGS
474 #define CONFIG_BOOTCOMMAND		"run boot_cramfs"
475 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE
476 
477 #define CONFIG_JFFS2_NAND
478 #define CONFIG_JFFS2_DEV		"0"
479 
480 /* mtdparts command line support */
481 #define CONFIG_CMD_MTDPARTS
482 #define CONFIG_FLASH_CFI_MTD
483 #define CONFIG_MTD_DEVICE
484 #define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
485 #define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
486 					"768k(BOOT-BIN)," \
487 					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
488 					"e1000000.flash:-(ubi)"
489 
490 #define CONFIG_EXTRA_ENV_SETTINGS \
491 	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
492 	"ethprime=TSEC1\0"						\
493 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
494 	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
495 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
496 		" +${filesize}; "					\
497 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
498 		" +${filesize}; "					\
499 		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
500 		" ${filesize}; "					\
501 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
502 		" +${filesize}; "					\
503 		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
504 		" ${filesize}\0"					\
505 	"console=ttyS0\0"						\
506 	"fdtaddr=0x780000\0"						\
507 	"kernel_addr=ff800000\0"					\
508 	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
509 	"setbootargs=setenv bootargs "					\
510 		"root=${rootdev} rw console=${console},"		\
511 			"${baudrate} ${othbootargs}\0"			\
512 	"setipargs=setenv bootargs root=${rootdev} rw "			\
513 			"nfsroot=${serverip}:${rootpath} "		\
514 			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
515 			"${netmask}:${hostname}:${netdev}:off "		\
516 			"console=${console},${baudrate} ${othbootargs}\0" \
517 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
518 	"mtdids=" MTDIDS_DEFAULT "\0"					\
519 	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
520 	"\0"
521 
522 #define CONFIG_NFSBOOTCOMMAND						\
523 	"setenv rootdev /dev/nfs;"					\
524 	"run setipargs;run addmtd;"					\
525 	"tftp ${loadaddr} ${bootfile};"				\
526 	"tftp ${fdtaddr} ${fdtfile};"					\
527 	"fdt addr ${fdtaddr};"						\
528 	"bootm ${loadaddr} - ${fdtaddr}"
529 
530 /* UBI Support */
531 #define CONFIG_CMD_NAND_TRIMFFS
532 #define CONFIG_CMD_UBIFS
533 #define CONFIG_RBTREE
534 #define CONFIG_LZO
535 #define CONFIG_MTD_PARTITIONS
536 
537 /* bootcount support */
538 #define CONFIG_BOOTCOUNT_LIMIT
539 #define CONFIG_BOOTCOUNT_I2C
540 #define CONFIG_BOOTCOUNT_ALEN	1
541 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
542 
543 #define CONFIG_IMAGE_FORMAT_LEGACY
544 #define CONFIG_CMD_HASH
545 #define CONFIG_SHA1
546 #define CONFIG_SHA256
547 
548 #endif	/* __CONFIG_H */
549