xref: /openbmc/u-boot/include/configs/ids8313.h (revision ea743e65)
1 /*
2  * (C) Copyright 2013
3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
4  *
5  * Based on:
6  * Copyright (c) 2011 IDS GmbH, Germany
7  * Sergej Stepanov <ste@ids.de>
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #ifndef __CONFIG_H
13 #define __CONFIG_H
14 
15 /*
16  * High Level Configuration Options
17  */
18 #define CONFIG_MPC831x
19 #define CONFIG_MPC8313
20 #define CONFIG_IDS8313
21 
22 #define CONFIG_FSL_ELBC
23 
24 #define CONFIG_MISC_INIT_R
25 
26 #define CONFIG_BOOT_RETRY_TIME		900
27 #define CONFIG_BOOT_RETRY_MIN		30
28 #define CONFIG_BOOTDELAY		1
29 #define CONFIG_RESET_TO_RETRY
30 
31 #define CONFIG_83XX_CLKIN		66000000	/* in Hz */
32 #define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
33 
34 #define CONFIG_SYS_IMMR		0xF0000000
35 
36 #define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
37 #define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
38 
39 /*
40  * Hardware Reset Configuration Word
41  * if CLKIN is 66.000MHz, then
42  * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
43  */
44 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
45 			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
46 			     HRCWL_CSB_TO_CLKIN_2X1 |\
47 			     HRCWL_CORE_TO_CSB_2X1)
48 
49 #define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
50 				 HRCWH_CORE_ENABLE |\
51 				 HRCWH_FROM_0XFFF00100 |\
52 				 HRCWH_BOOTSEQ_DISABLE |\
53 				 HRCWH_SW_WATCHDOG_DISABLE |\
54 				 HRCWH_ROM_LOC_LOCAL_8BIT |\
55 				 HRCWH_RL_EXT_LEGACY |\
56 				 HRCWH_TSEC1M_IN_MII |\
57 				 HRCWH_TSEC2M_IN_MII |\
58 				 HRCWH_BIG_ENDIAN)
59 
60 #define CONFIG_SYS_SICRH	0x00000000
61 #define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
62 
63 #define CONFIG_HWCONFIG
64 
65 #define CONFIG_SYS_HID0_INIT	0x000000000
66 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
67 				 HID0_ENABLE_INSTRUCTION_CACHE |\
68 				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
69 
70 #define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
71 
72 /*
73  * Definitions for initial stack pointer and data area (in DCACHE )
74  */
75 #define CONFIG_SYS_INIT_RAM_LOCK
76 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
77 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
78 #define CONFIG_SYS_GBL_DATA_SIZE	0x100
79 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
80 					 - CONFIG_SYS_GBL_DATA_SIZE)
81 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
82 
83 /*
84  * Local Bus LCRR and LBCR regs
85  */
86 #define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
87 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
88 #define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
89 					 (0xFF << LBCR_BMT_SHIFT) |\
90 					 0xF)
91 
92 #define CONFIG_SYS_LBC_MRTPR		0x20000000
93 
94 /*
95  * Internal Definitions
96  */
97 /*
98  * DDR Setup
99  */
100 #define CONFIG_SYS_DDR_BASE		0x00000000
101 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
102 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
103 
104 /*
105  * Manually set up DDR parameters,
106  * as this board has not the SPD connected to I2C.
107  */
108 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
109 #define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
110 					 0x00010000 |\
111 					 CSCONFIG_ROW_BIT_13 |\
112 					 CSCONFIG_COL_BIT_10)
113 
114 #define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
115 					 CSCONFIG_BANK_BIT_3)
116 
117 #define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
118 #define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
119 				(3 << TIMING_CFG0_WRT_SHIFT) |\
120 				(3 << TIMING_CFG0_RRT_SHIFT) |\
121 				(3 << TIMING_CFG0_WWT_SHIFT) |\
122 				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
123 				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
124 				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
125 				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
126 #define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
127 				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
128 				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
129 				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
130 				(4 << TIMING_CFG1_REFREC_SHIFT) |\
131 				(4 << TIMING_CFG1_WRREC_SHIFT) |\
132 				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
133 				(2 << TIMING_CFG1_WRTORD_SHIFT))
134 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
135 				(5 << TIMING_CFG2_CPO_SHIFT) |\
136 				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
137 				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
138 				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
139 				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
140 				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
141 
142 #define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
143 				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
144 
145 #define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
146 					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
147 					 SDRAM_CFG_DBW_32 |\
148 					 SDRAM_CFG_SDRAM_TYPE_DDR2)
149 
150 #define CONFIG_SYS_SDRAM_CFG2		0x00401000
151 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
152 					 (0x0242 << SDRAM_MODE_SD_SHIFT))
153 #define CONFIG_SYS_DDR_MODE_2		0x00000000
154 #define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
155 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
156 					 DDRCDR_PZ_NOMZ |\
157 					 DDRCDR_NZ_NOMZ |\
158 					 DDRCDR_ODT |\
159 					 DDRCDR_M_ODR |\
160 					 DDRCDR_Q_DRN)
161 
162 /*
163  * on-board devices
164  */
165 #define CONFIG_TSEC1
166 #define CONFIG_TSEC2
167 #define CONFIG_TSEC_ENET
168 #define CONFIG_HARD_SPI
169 #define CONFIG_HARD_I2C
170 
171 /*
172  * NOR FLASH setup
173  */
174 #define CONFIG_SYS_FLASH_CFI
175 #define CONFIG_FLASH_CFI_DRIVER
176 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
177 #define CONFIG_FLASH_SHOW_PROGRESS	50
178 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
179 
180 #define CONFIG_SYS_FLASH_BASE		0xFF800000
181 #define CONFIG_SYS_FLASH_SIZE		8
182 #define CONFIG_SYS_FLASH_PROTECTION
183 
184 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
185 #define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
186 
187 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
188 					 BR_PS_8 |\
189 					 BR_MS_GPCM |\
190 					 BR_V)
191 
192 #define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
193 					 OR_GPCM_SCY_10 |\
194 					 OR_GPCM_EHTR |\
195 					 OR_GPCM_TRLX |\
196 					 OR_GPCM_CSNT |\
197 					 OR_GPCM_EAD)
198 #define CONFIG_SYS_MAX_FLASH_BANKS	1
199 #define CONFIG_SYS_MAX_FLASH_SECT	128
200 
201 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000
202 #define CONFIG_SYS_FLASH_WRITE_TOUT	500
203 
204 /*
205  * NAND FLASH setup
206  */
207 #define CONFIG_SYS_NAND_BASE		0xE1000000
208 #define CONFIG_SYS_MAX_NAND_DEVICE	1
209 #define CONFIG_SYS_NAND_MAX_CHIPS	1
210 #define CONFIG_NAND_FSL_ELBC
211 #define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
212 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
213 #define NAND_CACHE_PAGES		64
214 
215 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
216 #define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
217 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
218 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
219 
220 #define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
221 				 (2<<BR_DECC_SHIFT) |\
222 				 BR_PS_8 |\
223 				 BR_MS_FCM |\
224 				 BR_V)
225 
226 #define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
227 				 OR_FCM_PGS |\
228 				 OR_FCM_CSCT |\
229 				 OR_FCM_CST |\
230 				 OR_FCM_CHT |\
231 				 OR_FCM_SCY_4 |\
232 				 OR_FCM_TRLX |\
233 				 OR_FCM_EHTR |\
234 				 OR_FCM_RST)
235 
236 /*
237  * MRAM setup
238  */
239 #define CONFIG_SYS_MRAM_BASE		0xE2000000
240 #define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
241 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
242 #define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
243 
244 #define CONFIG_SYS_OR_TIMING_MRAM
245 
246 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
247 					 BR_PS_8 |\
248 					 BR_MS_GPCM |\
249 					 BR_V)
250 
251 #define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
252 
253 /*
254  * CPLD setup
255  */
256 #define CONFIG_SYS_CPLD_BASE		0xE3000000
257 #define CONFIG_SYS_CPLD_SIZE		0x8000
258 #define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
259 #define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
260 
261 #define CONFIG_SYS_OR_TIMING_MRAM
262 
263 #define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
264 					 BR_PS_8 |\
265 					 BR_MS_GPCM |\
266 					 BR_V)
267 
268 #define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
269 
270 /*
271  * HW-Watchdog
272  */
273 #define CONFIG_WATCHDOG		1
274 #define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
275 
276 /*
277  * I2C setup
278  */
279 #define CONFIG_SYS_I2C
280 #define CONFIG_SYS_I2C_FSL
281 #define CONFIG_SYS_FSL_I2C_SPEED	400000
282 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
283 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
284 #define CONFIG_RTC_PCF8563
285 #define CONFIG_SYS_I2C_RTC_ADDR	0x51
286 
287 /*
288  * SPI setup
289  */
290 #ifdef CONFIG_HARD_SPI
291 #define CONFIG_MPC8XXX_SPI
292 #define CONFIG_SYS_GPIO1_PRELIM
293 #define CONFIG_SYS_GPIO1_DIR		0x00000001
294 #define CONFIG_SYS_GPIO1_DAT		0x00000001
295 #endif
296 
297 /*
298  * Ethernet setup
299  */
300 #ifdef CONFIG_TSEC1
301 #define CONFIG_HAS_ETH0
302 #define CONFIG_TSEC1_NAME		"TSEC0"
303 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
304 #define TSEC1_PHY_ADDR			0x1
305 #define TSEC1_FLAGS			TSEC_GIGABIT
306 #define TSEC1_PHYIDX			0
307 #endif
308 
309 #ifdef CONFIG_TSEC2
310 #define CONFIG_HAS_ETH1
311 #define CONFIG_TSEC2_NAME		"TSEC1"
312 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
313 #define TSEC2_PHY_ADDR			0x3
314 #define TSEC2_FLAGS			TSEC_GIGABIT
315 #define TSEC2_PHYIDX			0
316 #endif
317 #define CONFIG_ETHPRIME		"TSEC1"
318 
319 /*
320  * Serial Port
321  */
322 #define CONFIG_CONS_INDEX		1
323 #define CONFIG_SYS_NS16550_SERIAL
324 #define CONFIG_SYS_NS16550_REG_SIZE	1
325 
326 #define CONFIG_SYS_BAUDRATE_TABLE	\
327 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
328 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
329 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
330 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
331 
332 #define CONFIG_HAS_FSL_DR_USB
333 #define CONFIG_SYS_SCCR_USBDRCM	3
334 
335 /*
336  * BAT's
337  */
338 #define CONFIG_HIGH_BATS
339 
340 /* DDR @ 0x00000000 */
341 #define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
342 					 BATL_PP_10)
343 #define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
344 					 BATU_BL_256M |\
345 					 BATU_VS |\
346 					 BATU_VP)
347 #define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
348 #define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
349 
350 /* Initial RAM @ 0xFD000000 */
351 #define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
352 					 BATL_PP_10 |\
353 					 BATL_GUARDEDSTORAGE)
354 #define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
355 					 BATU_BL_256K |\
356 					 BATU_VS |\
357 					 BATU_VP)
358 #define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
359 #define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
360 
361 /* FLASH @ 0xFF800000 */
362 #define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
363 					 BATL_PP_10 |\
364 					 BATL_GUARDEDSTORAGE)
365 #define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
366 					 BATU_BL_8M |\
367 					 BATU_VS |\
368 					 BATU_VP)
369 #define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
370 					 BATL_PP_10 |\
371 					 BATL_CACHEINHIBIT |\
372 					 BATL_GUARDEDSTORAGE)
373 #define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
374 
375 #define CONFIG_SYS_IBAT3L		(0)
376 #define CONFIG_SYS_IBAT3U		(0)
377 #define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
378 #define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
379 
380 #define CONFIG_SYS_IBAT4L		(0)
381 #define CONFIG_SYS_IBAT4U		(0)
382 #define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
383 #define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
384 
385 /* IMMRBAR @ 0xF0000000 */
386 #define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
387 					 BATL_PP_10 |\
388 					 BATL_CACHEINHIBIT |\
389 					 BATL_GUARDEDSTORAGE)
390 #define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
391 					 BATU_BL_128M |\
392 					 BATU_VS |\
393 					 BATU_VP)
394 #define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
395 #define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
396 
397 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
398 #define CONFIG_SYS_IBAT6L		(0xE0000000 |\
399 					 BATL_PP_10 |\
400 					 BATL_GUARDEDSTORAGE)
401 #define CONFIG_SYS_IBAT6U		(0xE0000000 |\
402 					 BATU_BL_256M |\
403 					 BATU_VS |\
404 					 BATU_VP)
405 #define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
406 #define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
407 
408 #define CONFIG_SYS_IBAT7L		(0)
409 #define CONFIG_SYS_IBAT7U		(0)
410 #define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
411 #define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
412 
413 /*
414  * U-Boot environment setup
415  */
416 #define CONFIG_CMD_NAND
417 #define CONFIG_CMD_DATE
418 #define CONFIG_CMDLINE_EDITING
419 #define CONFIG_CMD_JFFS2
420 #define CONFIG_BOOTP_SUBNETMASK
421 #define CONFIG_BOOTP_GATEWAY
422 #define CONFIG_BOOTP_HOSTNAME
423 #define CONFIG_BOOTP_BOOTPATH
424 #define CONFIG_BOOTP_BOOTFILESIZE
425 
426 /*
427  * The reserved memory
428  */
429 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
430 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
431 #define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
432 
433 /*
434  * Environment Configuration
435  */
436 #define CONFIG_ENV_IS_IN_FLASH
437 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
438 				+ CONFIG_SYS_MONITOR_LEN)
439 #define CONFIG_ENV_SIZE		0x20000
440 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
441 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
442 
443 #define CONFIG_NETDEV			eth1
444 #define CONFIG_HOSTNAME		ids8313
445 #define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
446 #define CONFIG_BOOTFILE		"ids8313/uImage"
447 #define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
448 #define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
449 #define CONFIG_LOADADDR		0x400000
450 #define CONFIG_CMD_ENV_FLAGS
451 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
452 
453 #define CONFIG_BAUDRATE		115200
454 
455 /* Initial Memory map for Linux*/
456 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
457 
458 /*
459  * Miscellaneous configurable options
460  */
461 #define CONFIG_SYS_LONGHELP
462 #define CONFIG_SYS_CBSIZE		1024
463 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
464 					 + sizeof(CONFIG_SYS_PROMPT)+16)
465 #define CONFIG_SYS_MAXARGS		16
466 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
467 
468 #define CONFIG_SYS_MEMTEST_START	0x00001000
469 #define CONFIG_SYS_MEMTEST_END		0x00C00000
470 
471 #define CONFIG_SYS_LOAD_ADDR		0x100000
472 #define CONFIG_MII
473 #define CONFIG_LOADS_ECHO
474 #define CONFIG_TIMESTAMP
475 #define CONFIG_PREBOOT			"echo;" \
476 					"echo Type \\\"run nfsboot\\\" " \
477 					"to mount root filesystem over NFS;echo"
478 #undef	CONFIG_BOOTARGS
479 #define CONFIG_BOOTCOMMAND		"run boot_cramfs"
480 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE
481 
482 #define CONFIG_JFFS2_NAND
483 #define CONFIG_JFFS2_DEV		"0"
484 
485 /* mtdparts command line support */
486 #define CONFIG_CMD_MTDPARTS
487 #define CONFIG_FLASH_CFI_MTD
488 #define CONFIG_MTD_DEVICE
489 #define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
490 #define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
491 					"768k(BOOT-BIN)," \
492 					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
493 					"e1000000.flash:-(ubi)"
494 
495 #define CONFIG_EXTRA_ENV_SETTINGS \
496 	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
497 	"ethprime=TSEC1\0"						\
498 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
499 	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
500 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
501 		" +${filesize}; "					\
502 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
503 		" +${filesize}; "					\
504 		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
505 		" ${filesize}; "					\
506 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
507 		" +${filesize}; "					\
508 		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
509 		" ${filesize}\0"					\
510 	"console=ttyS0\0"						\
511 	"fdtaddr=0x780000\0"						\
512 	"kernel_addr=ff800000\0"					\
513 	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
514 	"setbootargs=setenv bootargs "					\
515 		"root=${rootdev} rw console=${console},"		\
516 			"${baudrate} ${othbootargs}\0"			\
517 	"setipargs=setenv bootargs root=${rootdev} rw "			\
518 			"nfsroot=${serverip}:${rootpath} "		\
519 			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
520 			"${netmask}:${hostname}:${netdev}:off "		\
521 			"console=${console},${baudrate} ${othbootargs}\0" \
522 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
523 	"mtdids=" MTDIDS_DEFAULT "\0"					\
524 	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
525 	"\0"
526 
527 #define CONFIG_NFSBOOTCOMMAND						\
528 	"setenv rootdev /dev/nfs;"					\
529 	"run setipargs;run addmtd;"					\
530 	"tftp ${loadaddr} ${bootfile};"				\
531 	"tftp ${fdtaddr} ${fdtfile};"					\
532 	"fdt addr ${fdtaddr};"						\
533 	"bootm ${loadaddr} - ${fdtaddr}"
534 
535 /* UBI Support */
536 #define CONFIG_CMD_NAND_TRIMFFS
537 #define CONFIG_CMD_UBI
538 #define CONFIG_CMD_UBIFS
539 #define CONFIG_RBTREE
540 #define CONFIG_LZO
541 #define CONFIG_MTD_PARTITIONS
542 
543 /* bootcount support */
544 #define CONFIG_BOOTCOUNT_LIMIT
545 #define CONFIG_BOOTCOUNT_I2C
546 #define CONFIG_BOOTCOUNT_ALEN	1
547 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
548 
549 #define CONFIG_VERSION_VARIABLE
550 
551 #define CONFIG_IMAGE_FORMAT_LEGACY
552 #define CONFIG_CMD_HASH
553 #define CONFIG_SHA1
554 #define CONFIG_SHA256
555 
556 #endif	/* __CONFIG_H */
557