xref: /openbmc/u-boot/include/configs/ids8313.h (revision d891ab95)
1 /*
2  * (C) Copyright 2013
3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
4  *
5  * Based on:
6  * Copyright (c) 2011 IDS GmbH, Germany
7  * Sergej Stepanov <ste@ids.de>
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #ifndef __CONFIG_H
13 #define __CONFIG_H
14 
15 /*
16  * High Level Configuration Options
17  */
18 #define CONFIG_MPC831x
19 #define CONFIG_MPC8313
20 #define CONFIG_IDS8313
21 
22 #define CONFIG_FSL_ELBC
23 
24 #define CONFIG_MISC_INIT_R
25 
26 #define CONFIG_BOOT_RETRY_TIME		900
27 #define CONFIG_BOOT_RETRY_MIN		30
28 #define CONFIG_RESET_TO_RETRY
29 
30 #define CONFIG_83XX_CLKIN		66000000	/* in Hz */
31 #define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
32 
33 #define CONFIG_SYS_IMMR		0xF0000000
34 
35 #define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
36 #define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
37 
38 /*
39  * Hardware Reset Configuration Word
40  * if CLKIN is 66.000MHz, then
41  * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
42  */
43 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
44 			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
45 			     HRCWL_CSB_TO_CLKIN_2X1 |\
46 			     HRCWL_CORE_TO_CSB_2X1)
47 
48 #define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
49 				 HRCWH_CORE_ENABLE |\
50 				 HRCWH_FROM_0XFFF00100 |\
51 				 HRCWH_BOOTSEQ_DISABLE |\
52 				 HRCWH_SW_WATCHDOG_DISABLE |\
53 				 HRCWH_ROM_LOC_LOCAL_8BIT |\
54 				 HRCWH_RL_EXT_LEGACY |\
55 				 HRCWH_TSEC1M_IN_MII |\
56 				 HRCWH_TSEC2M_IN_MII |\
57 				 HRCWH_BIG_ENDIAN)
58 
59 #define CONFIG_SYS_SICRH	0x00000000
60 #define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
61 
62 #define CONFIG_HWCONFIG
63 
64 #define CONFIG_SYS_HID0_INIT	0x000000000
65 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
66 				 HID0_ENABLE_INSTRUCTION_CACHE |\
67 				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
68 
69 #define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
70 
71 /*
72  * Definitions for initial stack pointer and data area (in DCACHE )
73  */
74 #define CONFIG_SYS_INIT_RAM_LOCK
75 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
76 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
77 #define CONFIG_SYS_GBL_DATA_SIZE	0x100
78 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
79 					 - CONFIG_SYS_GBL_DATA_SIZE)
80 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
81 
82 /*
83  * Local Bus LCRR and LBCR regs
84  */
85 #define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
86 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
87 #define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
88 					 (0xFF << LBCR_BMT_SHIFT) |\
89 					 0xF)
90 
91 #define CONFIG_SYS_LBC_MRTPR		0x20000000
92 
93 /*
94  * Internal Definitions
95  */
96 /*
97  * DDR Setup
98  */
99 #define CONFIG_SYS_DDR_BASE		0x00000000
100 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
101 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
102 
103 /*
104  * Manually set up DDR parameters,
105  * as this board has not the SPD connected to I2C.
106  */
107 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
108 #define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
109 					 0x00010000 |\
110 					 CSCONFIG_ROW_BIT_13 |\
111 					 CSCONFIG_COL_BIT_10)
112 
113 #define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
114 					 CSCONFIG_BANK_BIT_3)
115 
116 #define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
117 #define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
118 				(3 << TIMING_CFG0_WRT_SHIFT) |\
119 				(3 << TIMING_CFG0_RRT_SHIFT) |\
120 				(3 << TIMING_CFG0_WWT_SHIFT) |\
121 				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
122 				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
123 				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
124 				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
125 #define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
126 				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
127 				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
128 				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
129 				(4 << TIMING_CFG1_REFREC_SHIFT) |\
130 				(4 << TIMING_CFG1_WRREC_SHIFT) |\
131 				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
132 				(2 << TIMING_CFG1_WRTORD_SHIFT))
133 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
134 				(5 << TIMING_CFG2_CPO_SHIFT) |\
135 				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
136 				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
137 				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
138 				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
139 				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
140 
141 #define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
142 				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
143 
144 #define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
145 					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
146 					 SDRAM_CFG_DBW_32 |\
147 					 SDRAM_CFG_SDRAM_TYPE_DDR2)
148 
149 #define CONFIG_SYS_SDRAM_CFG2		0x00401000
150 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
151 					 (0x0242 << SDRAM_MODE_SD_SHIFT))
152 #define CONFIG_SYS_DDR_MODE_2		0x00000000
153 #define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
154 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
155 					 DDRCDR_PZ_NOMZ |\
156 					 DDRCDR_NZ_NOMZ |\
157 					 DDRCDR_ODT |\
158 					 DDRCDR_M_ODR |\
159 					 DDRCDR_Q_DRN)
160 
161 /*
162  * on-board devices
163  */
164 #define CONFIG_TSEC1
165 #define CONFIG_TSEC2
166 #define CONFIG_TSEC_ENET
167 #define CONFIG_HARD_SPI
168 #define CONFIG_HARD_I2C
169 
170 /*
171  * NOR FLASH setup
172  */
173 #define CONFIG_SYS_FLASH_CFI
174 #define CONFIG_FLASH_CFI_DRIVER
175 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
176 #define CONFIG_FLASH_SHOW_PROGRESS	50
177 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
178 
179 #define CONFIG_SYS_FLASH_BASE		0xFF800000
180 #define CONFIG_SYS_FLASH_SIZE		8
181 #define CONFIG_SYS_FLASH_PROTECTION
182 
183 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
184 #define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
185 
186 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
187 					 BR_PS_8 |\
188 					 BR_MS_GPCM |\
189 					 BR_V)
190 
191 #define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
192 					 OR_GPCM_SCY_10 |\
193 					 OR_GPCM_EHTR |\
194 					 OR_GPCM_TRLX |\
195 					 OR_GPCM_CSNT |\
196 					 OR_GPCM_EAD)
197 #define CONFIG_SYS_MAX_FLASH_BANKS	1
198 #define CONFIG_SYS_MAX_FLASH_SECT	128
199 
200 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000
201 #define CONFIG_SYS_FLASH_WRITE_TOUT	500
202 
203 /*
204  * NAND FLASH setup
205  */
206 #define CONFIG_SYS_NAND_BASE		0xE1000000
207 #define CONFIG_SYS_MAX_NAND_DEVICE	1
208 #define CONFIG_SYS_NAND_MAX_CHIPS	1
209 #define CONFIG_NAND_FSL_ELBC
210 #define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
211 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
212 #define NAND_CACHE_PAGES		64
213 
214 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
215 #define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
216 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
217 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
218 
219 #define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
220 				 (2<<BR_DECC_SHIFT) |\
221 				 BR_PS_8 |\
222 				 BR_MS_FCM |\
223 				 BR_V)
224 
225 #define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
226 				 OR_FCM_PGS |\
227 				 OR_FCM_CSCT |\
228 				 OR_FCM_CST |\
229 				 OR_FCM_CHT |\
230 				 OR_FCM_SCY_4 |\
231 				 OR_FCM_TRLX |\
232 				 OR_FCM_EHTR |\
233 				 OR_FCM_RST)
234 
235 /*
236  * MRAM setup
237  */
238 #define CONFIG_SYS_MRAM_BASE		0xE2000000
239 #define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
240 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
241 #define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
242 
243 #define CONFIG_SYS_OR_TIMING_MRAM
244 
245 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
246 					 BR_PS_8 |\
247 					 BR_MS_GPCM |\
248 					 BR_V)
249 
250 #define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
251 
252 /*
253  * CPLD setup
254  */
255 #define CONFIG_SYS_CPLD_BASE		0xE3000000
256 #define CONFIG_SYS_CPLD_SIZE		0x8000
257 #define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
258 #define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
259 
260 #define CONFIG_SYS_OR_TIMING_MRAM
261 
262 #define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
263 					 BR_PS_8 |\
264 					 BR_MS_GPCM |\
265 					 BR_V)
266 
267 #define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
268 
269 /*
270  * HW-Watchdog
271  */
272 #define CONFIG_WATCHDOG		1
273 #define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
274 
275 /*
276  * I2C setup
277  */
278 #define CONFIG_SYS_I2C
279 #define CONFIG_SYS_I2C_FSL
280 #define CONFIG_SYS_FSL_I2C_SPEED	400000
281 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
282 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
283 #define CONFIG_RTC_PCF8563
284 #define CONFIG_SYS_I2C_RTC_ADDR	0x51
285 
286 /*
287  * SPI setup
288  */
289 #ifdef CONFIG_HARD_SPI
290 #define CONFIG_MPC8XXX_SPI
291 #define CONFIG_SYS_GPIO1_PRELIM
292 #define CONFIG_SYS_GPIO1_DIR		0x00000001
293 #define CONFIG_SYS_GPIO1_DAT		0x00000001
294 #endif
295 
296 /*
297  * Ethernet setup
298  */
299 #ifdef CONFIG_TSEC1
300 #define CONFIG_HAS_ETH0
301 #define CONFIG_TSEC1_NAME		"TSEC0"
302 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
303 #define TSEC1_PHY_ADDR			0x1
304 #define TSEC1_FLAGS			TSEC_GIGABIT
305 #define TSEC1_PHYIDX			0
306 #endif
307 
308 #ifdef CONFIG_TSEC2
309 #define CONFIG_HAS_ETH1
310 #define CONFIG_TSEC2_NAME		"TSEC1"
311 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
312 #define TSEC2_PHY_ADDR			0x3
313 #define TSEC2_FLAGS			TSEC_GIGABIT
314 #define TSEC2_PHYIDX			0
315 #endif
316 #define CONFIG_ETHPRIME		"TSEC1"
317 
318 /*
319  * Serial Port
320  */
321 #define CONFIG_CONS_INDEX		1
322 #define CONFIG_SYS_NS16550_SERIAL
323 #define CONFIG_SYS_NS16550_REG_SIZE	1
324 
325 #define CONFIG_SYS_BAUDRATE_TABLE	\
326 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
327 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
328 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
329 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
330 
331 #define CONFIG_HAS_FSL_DR_USB
332 #define CONFIG_SYS_SCCR_USBDRCM	3
333 
334 /*
335  * BAT's
336  */
337 #define CONFIG_HIGH_BATS
338 
339 /* DDR @ 0x00000000 */
340 #define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
341 					 BATL_PP_10)
342 #define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
343 					 BATU_BL_256M |\
344 					 BATU_VS |\
345 					 BATU_VP)
346 #define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
347 #define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
348 
349 /* Initial RAM @ 0xFD000000 */
350 #define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
351 					 BATL_PP_10 |\
352 					 BATL_GUARDEDSTORAGE)
353 #define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
354 					 BATU_BL_256K |\
355 					 BATU_VS |\
356 					 BATU_VP)
357 #define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
358 #define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
359 
360 /* FLASH @ 0xFF800000 */
361 #define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
362 					 BATL_PP_10 |\
363 					 BATL_GUARDEDSTORAGE)
364 #define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
365 					 BATU_BL_8M |\
366 					 BATU_VS |\
367 					 BATU_VP)
368 #define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
369 					 BATL_PP_10 |\
370 					 BATL_CACHEINHIBIT |\
371 					 BATL_GUARDEDSTORAGE)
372 #define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
373 
374 #define CONFIG_SYS_IBAT3L		(0)
375 #define CONFIG_SYS_IBAT3U		(0)
376 #define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
377 #define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
378 
379 #define CONFIG_SYS_IBAT4L		(0)
380 #define CONFIG_SYS_IBAT4U		(0)
381 #define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
382 #define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
383 
384 /* IMMRBAR @ 0xF0000000 */
385 #define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
386 					 BATL_PP_10 |\
387 					 BATL_CACHEINHIBIT |\
388 					 BATL_GUARDEDSTORAGE)
389 #define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
390 					 BATU_BL_128M |\
391 					 BATU_VS |\
392 					 BATU_VP)
393 #define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
394 #define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
395 
396 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
397 #define CONFIG_SYS_IBAT6L		(0xE0000000 |\
398 					 BATL_PP_10 |\
399 					 BATL_GUARDEDSTORAGE)
400 #define CONFIG_SYS_IBAT6U		(0xE0000000 |\
401 					 BATU_BL_256M |\
402 					 BATU_VS |\
403 					 BATU_VP)
404 #define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
405 #define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
406 
407 #define CONFIG_SYS_IBAT7L		(0)
408 #define CONFIG_SYS_IBAT7U		(0)
409 #define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
410 #define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
411 
412 /*
413  * U-Boot environment setup
414  */
415 #define CONFIG_CMD_NAND
416 #define CONFIG_CMD_DATE
417 #define CONFIG_CMDLINE_EDITING
418 #define CONFIG_CMD_JFFS2
419 #define CONFIG_BOOTP_SUBNETMASK
420 #define CONFIG_BOOTP_GATEWAY
421 #define CONFIG_BOOTP_HOSTNAME
422 #define CONFIG_BOOTP_BOOTPATH
423 #define CONFIG_BOOTP_BOOTFILESIZE
424 
425 /*
426  * The reserved memory
427  */
428 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
429 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
430 #define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
431 
432 /*
433  * Environment Configuration
434  */
435 #define CONFIG_ENV_IS_IN_FLASH
436 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
437 				+ CONFIG_SYS_MONITOR_LEN)
438 #define CONFIG_ENV_SIZE		0x20000
439 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
440 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
441 
442 #define CONFIG_NETDEV			eth1
443 #define CONFIG_HOSTNAME		ids8313
444 #define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
445 #define CONFIG_BOOTFILE		"ids8313/uImage"
446 #define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
447 #define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
448 #define CONFIG_LOADADDR		0x400000
449 #define CONFIG_CMD_ENV_FLAGS
450 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
451 
452 /* Initial Memory map for Linux*/
453 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
454 
455 /*
456  * Miscellaneous configurable options
457  */
458 #define CONFIG_SYS_LONGHELP
459 #define CONFIG_SYS_CBSIZE		1024
460 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
461 					 + sizeof(CONFIG_SYS_PROMPT)+16)
462 #define CONFIG_SYS_MAXARGS		16
463 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
464 
465 #define CONFIG_SYS_MEMTEST_START	0x00001000
466 #define CONFIG_SYS_MEMTEST_END		0x00C00000
467 
468 #define CONFIG_SYS_LOAD_ADDR		0x100000
469 #define CONFIG_MII
470 #define CONFIG_LOADS_ECHO
471 #define CONFIG_TIMESTAMP
472 #define CONFIG_PREBOOT			"echo;" \
473 					"echo Type \\\"run nfsboot\\\" " \
474 					"to mount root filesystem over NFS;echo"
475 #undef	CONFIG_BOOTARGS
476 #define CONFIG_BOOTCOMMAND		"run boot_cramfs"
477 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE
478 
479 #define CONFIG_JFFS2_NAND
480 #define CONFIG_JFFS2_DEV		"0"
481 
482 /* mtdparts command line support */
483 #define CONFIG_CMD_MTDPARTS
484 #define CONFIG_FLASH_CFI_MTD
485 #define CONFIG_MTD_DEVICE
486 #define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
487 #define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
488 					"768k(BOOT-BIN)," \
489 					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
490 					"e1000000.flash:-(ubi)"
491 
492 #define CONFIG_EXTRA_ENV_SETTINGS \
493 	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
494 	"ethprime=TSEC1\0"						\
495 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
496 	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
497 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
498 		" +${filesize}; "					\
499 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
500 		" +${filesize}; "					\
501 		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
502 		" ${filesize}; "					\
503 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
504 		" +${filesize}; "					\
505 		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
506 		" ${filesize}\0"					\
507 	"console=ttyS0\0"						\
508 	"fdtaddr=0x780000\0"						\
509 	"kernel_addr=ff800000\0"					\
510 	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
511 	"setbootargs=setenv bootargs "					\
512 		"root=${rootdev} rw console=${console},"		\
513 			"${baudrate} ${othbootargs}\0"			\
514 	"setipargs=setenv bootargs root=${rootdev} rw "			\
515 			"nfsroot=${serverip}:${rootpath} "		\
516 			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
517 			"${netmask}:${hostname}:${netdev}:off "		\
518 			"console=${console},${baudrate} ${othbootargs}\0" \
519 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
520 	"mtdids=" MTDIDS_DEFAULT "\0"					\
521 	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
522 	"\0"
523 
524 #define CONFIG_NFSBOOTCOMMAND						\
525 	"setenv rootdev /dev/nfs;"					\
526 	"run setipargs;run addmtd;"					\
527 	"tftp ${loadaddr} ${bootfile};"				\
528 	"tftp ${fdtaddr} ${fdtfile};"					\
529 	"fdt addr ${fdtaddr};"						\
530 	"bootm ${loadaddr} - ${fdtaddr}"
531 
532 /* UBI Support */
533 #define CONFIG_CMD_NAND_TRIMFFS
534 #define CONFIG_CMD_UBIFS
535 #define CONFIG_RBTREE
536 #define CONFIG_LZO
537 #define CONFIG_MTD_PARTITIONS
538 
539 /* bootcount support */
540 #define CONFIG_BOOTCOUNT_LIMIT
541 #define CONFIG_BOOTCOUNT_I2C
542 #define CONFIG_BOOTCOUNT_ALEN	1
543 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
544 
545 #define CONFIG_IMAGE_FORMAT_LEGACY
546 #define CONFIG_CMD_HASH
547 #define CONFIG_SHA1
548 #define CONFIG_SHA256
549 
550 #endif	/* __CONFIG_H */
551