1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2013 4 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * Copyright (c) 2011 IDS GmbH, Germany 8 * Sergej Stepanov <ste@ids.de> 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_MPC831x 18 #define CONFIG_MPC8313 19 20 #define CONFIG_FSL_ELBC 21 22 #define CONFIG_MISC_INIT_R 23 24 #define CONFIG_BOOT_RETRY_TIME 900 25 #define CONFIG_BOOT_RETRY_MIN 30 26 #define CONFIG_RESET_TO_RETRY 27 28 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 29 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 30 31 #define CONFIG_SYS_IMMR 0xF0000000 32 33 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 34 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 35 36 /* 37 * Hardware Reset Configuration Word 38 * if CLKIN is 66.000MHz, then 39 * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz 40 */ 41 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\ 42 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 43 HRCWL_CSB_TO_CLKIN_2X1 |\ 44 HRCWL_CORE_TO_CSB_2X1) 45 46 #define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\ 47 HRCWH_CORE_ENABLE |\ 48 HRCWH_FROM_0XFFF00100 |\ 49 HRCWH_BOOTSEQ_DISABLE |\ 50 HRCWH_SW_WATCHDOG_DISABLE |\ 51 HRCWH_ROM_LOC_LOCAL_8BIT |\ 52 HRCWH_RL_EXT_LEGACY |\ 53 HRCWH_TSEC1M_IN_MII |\ 54 HRCWH_TSEC2M_IN_MII |\ 55 HRCWH_BIG_ENDIAN) 56 57 #define CONFIG_SYS_SICRH 0x00000000 58 #define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) 59 60 #define CONFIG_HWCONFIG 61 62 #define CONFIG_SYS_HID0_INIT 0x000000000 63 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\ 64 HID0_ENABLE_INSTRUCTION_CACHE |\ 65 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT) 66 67 #define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000) 68 69 /* 70 * Definitions for initial stack pointer and data area (in DCACHE ) 71 */ 72 #define CONFIG_SYS_INIT_RAM_LOCK 73 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 74 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ 75 #define CONFIG_SYS_GBL_DATA_SIZE 0x100 76 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ 77 - CONFIG_SYS_GBL_DATA_SIZE) 78 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 79 80 /* 81 * Local Bus LCRR and LBCR regs 82 */ 83 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 84 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 85 #define CONFIG_SYS_LBC_LBCR (0x00040000 |\ 86 (0xFF << LBCR_BMT_SHIFT) |\ 87 0xF) 88 89 #define CONFIG_SYS_LBC_MRTPR 0x20000000 90 91 /* 92 * Internal Definitions 93 */ 94 /* 95 * DDR Setup 96 */ 97 #define CONFIG_SYS_DDR_BASE 0x00000000 98 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 99 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 100 101 /* 102 * Manually set up DDR parameters, 103 * as this board has not the SPD connected to I2C. 104 */ 105 #define CONFIG_SYS_DDR_SIZE 256 /* MB */ 106 #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ 107 0x00010000 |\ 108 CSCONFIG_ROW_BIT_13 |\ 109 CSCONFIG_COL_BIT_10) 110 111 #define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ 112 CSCONFIG_BANK_BIT_3) 113 114 #define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ 115 #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ 116 (3 << TIMING_CFG0_WRT_SHIFT) |\ 117 (3 << TIMING_CFG0_RRT_SHIFT) |\ 118 (3 << TIMING_CFG0_WWT_SHIFT) |\ 119 (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ 120 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ 121 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ 122 (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 123 #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ 124 (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ 125 (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ 126 (7 << TIMING_CFG1_CASLAT_SHIFT) |\ 127 (4 << TIMING_CFG1_REFREC_SHIFT) |\ 128 (4 << TIMING_CFG1_WRREC_SHIFT) |\ 129 (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ 130 (2 << TIMING_CFG1_WRTORD_SHIFT)) 131 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ 132 (5 << TIMING_CFG2_CPO_SHIFT) |\ 133 (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ 134 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ 135 (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ 136 (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ 137 (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) 138 139 #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ 140 (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 141 142 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ 143 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ 144 SDRAM_CFG_DBW_32 |\ 145 SDRAM_CFG_SDRAM_TYPE_DDR2) 146 147 #define CONFIG_SYS_SDRAM_CFG2 0x00401000 148 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ 149 (0x0242 << SDRAM_MODE_SD_SHIFT)) 150 #define CONFIG_SYS_DDR_MODE_2 0x00000000 151 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 152 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ 153 DDRCDR_PZ_NOMZ |\ 154 DDRCDR_NZ_NOMZ |\ 155 DDRCDR_ODT |\ 156 DDRCDR_M_ODR |\ 157 DDRCDR_Q_DRN) 158 159 /* 160 * on-board devices 161 */ 162 #define CONFIG_TSEC1 163 #define CONFIG_TSEC2 164 #define CONFIG_HARD_SPI 165 166 /* 167 * NOR FLASH setup 168 */ 169 #define CONFIG_SYS_FLASH_CFI 170 #define CONFIG_FLASH_CFI_DRIVER 171 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT 172 #define CONFIG_FLASH_SHOW_PROGRESS 50 173 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 174 175 #define CONFIG_SYS_FLASH_BASE 0xFF800000 176 #define CONFIG_SYS_FLASH_SIZE 8 177 #define CONFIG_SYS_FLASH_PROTECTION 178 179 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 180 #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 181 182 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ 183 BR_PS_8 |\ 184 BR_MS_GPCM |\ 185 BR_V) 186 187 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ 188 OR_GPCM_SCY_10 |\ 189 OR_GPCM_EHTR |\ 190 OR_GPCM_TRLX |\ 191 OR_GPCM_CSNT |\ 192 OR_GPCM_EAD) 193 #define CONFIG_SYS_MAX_FLASH_BANKS 1 194 #define CONFIG_SYS_MAX_FLASH_SECT 128 195 196 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 197 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 198 199 /* 200 * NAND FLASH setup 201 */ 202 #define CONFIG_SYS_NAND_BASE 0xE1000000 203 #define CONFIG_SYS_MAX_NAND_DEVICE 1 204 #define CONFIG_SYS_NAND_MAX_CHIPS 1 205 #define CONFIG_NAND_FSL_ELBC 206 #define CONFIG_SYS_NAND_PAGE_SIZE (2048) 207 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) 208 #define NAND_CACHE_PAGES 64 209 210 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 211 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E 212 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 213 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 214 215 #define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\ 216 (2<<BR_DECC_SHIFT) |\ 217 BR_PS_8 |\ 218 BR_MS_FCM |\ 219 BR_V) 220 221 #define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\ 222 OR_FCM_PGS |\ 223 OR_FCM_CSCT |\ 224 OR_FCM_CST |\ 225 OR_FCM_CHT |\ 226 OR_FCM_SCY_4 |\ 227 OR_FCM_TRLX |\ 228 OR_FCM_EHTR |\ 229 OR_FCM_RST) 230 231 /* 232 * MRAM setup 233 */ 234 #define CONFIG_SYS_MRAM_BASE 0xE2000000 235 #define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ 236 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE 237 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */ 238 239 #define CONFIG_SYS_OR_TIMING_MRAM 240 241 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\ 242 BR_PS_8 |\ 243 BR_MS_GPCM |\ 244 BR_V) 245 246 #define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74 247 248 /* 249 * CPLD setup 250 */ 251 #define CONFIG_SYS_CPLD_BASE 0xE3000000 252 #define CONFIG_SYS_CPLD_SIZE 0x8000 253 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE 254 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E 255 256 #define CONFIG_SYS_OR_TIMING_MRAM 257 258 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\ 259 BR_PS_8 |\ 260 BR_MS_GPCM |\ 261 BR_V) 262 263 #define CONFIG_SYS_OR3_PRELIM 0xFFFF8814 264 265 /* 266 * HW-Watchdog 267 */ 268 #define CONFIG_WATCHDOG 1 269 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF 270 271 /* 272 * I2C setup 273 */ 274 #define CONFIG_SYS_I2C 275 #define CONFIG_SYS_I2C_FSL 276 #define CONFIG_SYS_FSL_I2C_SPEED 400000 277 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 278 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 279 #define CONFIG_RTC_PCF8563 280 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 281 282 /* 283 * SPI setup 284 */ 285 #ifdef CONFIG_HARD_SPI 286 #define CONFIG_SYS_GPIO1_PRELIM 287 #define CONFIG_SYS_GPIO1_DIR 0x00000001 288 #define CONFIG_SYS_GPIO1_DAT 0x00000001 289 #endif 290 291 /* 292 * Ethernet setup 293 */ 294 #ifdef CONFIG_TSEC1 295 #define CONFIG_HAS_ETH0 296 #define CONFIG_TSEC1_NAME "TSEC0" 297 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 298 #define TSEC1_PHY_ADDR 0x1 299 #define TSEC1_FLAGS TSEC_GIGABIT 300 #define TSEC1_PHYIDX 0 301 #endif 302 303 #ifdef CONFIG_TSEC2 304 #define CONFIG_HAS_ETH1 305 #define CONFIG_TSEC2_NAME "TSEC1" 306 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 307 #define TSEC2_PHY_ADDR 0x3 308 #define TSEC2_FLAGS TSEC_GIGABIT 309 #define TSEC2_PHYIDX 0 310 #endif 311 #define CONFIG_ETHPRIME "TSEC1" 312 313 /* 314 * Serial Port 315 */ 316 #define CONFIG_SYS_NS16550_SERIAL 317 #define CONFIG_SYS_NS16550_REG_SIZE 1 318 319 #define CONFIG_SYS_BAUDRATE_TABLE \ 320 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 321 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 322 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 323 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) 324 325 #define CONFIG_HAS_FSL_DR_USB 326 #define CONFIG_SYS_SCCR_USBDRCM 3 327 328 /* 329 * BAT's 330 */ 331 #define CONFIG_HIGH_BATS 332 333 /* DDR @ 0x00000000 */ 334 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\ 335 BATL_PP_10) 336 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\ 337 BATU_BL_256M |\ 338 BATU_VS |\ 339 BATU_VP) 340 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 341 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 342 343 /* Initial RAM @ 0xFD000000 */ 344 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\ 345 BATL_PP_10 |\ 346 BATL_GUARDEDSTORAGE) 347 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\ 348 BATU_BL_256K |\ 349 BATU_VS |\ 350 BATU_VP) 351 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 352 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 353 354 /* FLASH @ 0xFF800000 */ 355 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\ 356 BATL_PP_10 |\ 357 BATL_GUARDEDSTORAGE) 358 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\ 359 BATU_BL_8M |\ 360 BATU_VS |\ 361 BATU_VP) 362 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\ 363 BATL_PP_10 |\ 364 BATL_CACHEINHIBIT |\ 365 BATL_GUARDEDSTORAGE) 366 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 367 368 #define CONFIG_SYS_IBAT3L (0) 369 #define CONFIG_SYS_IBAT3U (0) 370 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 371 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 372 373 #define CONFIG_SYS_IBAT4L (0) 374 #define CONFIG_SYS_IBAT4U (0) 375 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 376 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 377 378 /* IMMRBAR @ 0xF0000000 */ 379 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\ 380 BATL_PP_10 |\ 381 BATL_CACHEINHIBIT |\ 382 BATL_GUARDEDSTORAGE) 383 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\ 384 BATU_BL_128M |\ 385 BATU_VS |\ 386 BATU_VP) 387 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 388 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 389 390 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */ 391 #define CONFIG_SYS_IBAT6L (0xE0000000 |\ 392 BATL_PP_10 |\ 393 BATL_GUARDEDSTORAGE) 394 #define CONFIG_SYS_IBAT6U (0xE0000000 |\ 395 BATU_BL_256M |\ 396 BATU_VS |\ 397 BATU_VP) 398 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 399 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 400 401 #define CONFIG_SYS_IBAT7L (0) 402 #define CONFIG_SYS_IBAT7U (0) 403 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 404 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 405 406 /* 407 * U-Boot environment setup 408 */ 409 #define CONFIG_BOOTP_BOOTFILESIZE 410 411 /* 412 * The reserved memory 413 */ 414 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 415 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 416 #define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) 417 418 /* 419 * Environment Configuration 420 */ 421 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 422 + CONFIG_SYS_MONITOR_LEN) 423 #define CONFIG_ENV_SIZE 0x20000 424 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) 425 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 426 427 #define CONFIG_NETDEV eth1 428 #define CONFIG_HOSTNAME "ids8313" 429 #define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" 430 #define CONFIG_BOOTFILE "ids8313/uImage" 431 #define CONFIG_UBOOTPATH "ids8313/u-boot.bin" 432 #define CONFIG_FDTFILE "ids8313/ids8313.dtb" 433 #define CONFIG_LOADADDR 0x400000 434 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" 435 436 /* Initial Memory map for Linux*/ 437 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 438 439 /* 440 * Miscellaneous configurable options 441 */ 442 #define CONFIG_SYS_CBSIZE 1024 443 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 444 445 #define CONFIG_SYS_MEMTEST_START 0x00001000 446 #define CONFIG_SYS_MEMTEST_END 0x00C00000 447 448 #define CONFIG_SYS_LOAD_ADDR 0x100000 449 #define CONFIG_MII 450 #define CONFIG_LOADS_ECHO 451 #define CONFIG_TIMESTAMP 452 #define CONFIG_PREBOOT "echo;" \ 453 "echo Type \\\"run nfsboot\\\" " \ 454 "to mount root filesystem over NFS;echo" 455 #define CONFIG_BOOTCOMMAND "run boot_cramfs" 456 #undef CONFIG_SYS_LOADS_BAUD_CHANGE 457 458 #define CONFIG_JFFS2_NAND 459 #define CONFIG_JFFS2_DEV "0" 460 461 /* mtdparts command line support */ 462 #define CONFIG_FLASH_CFI_MTD 463 #define CONFIG_MTD_DEVICE 464 465 #define CONFIG_EXTRA_ENV_SETTINGS \ 466 "netdev=" __stringify(CONFIG_NETDEV) "\0" \ 467 "ethprime=TSEC1\0" \ 468 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 469 "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ 470 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 471 " +${filesize}; " \ 472 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 473 " +${filesize}; " \ 474 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ 475 " ${filesize}; " \ 476 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 477 " +${filesize}; " \ 478 "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ 479 " ${filesize}\0" \ 480 "console=ttyS0\0" \ 481 "fdtaddr=0x780000\0" \ 482 "kernel_addr=ff800000\0" \ 483 "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ 484 "setbootargs=setenv bootargs " \ 485 "root=${rootdev} rw console=${console}," \ 486 "${baudrate} ${othbootargs}\0" \ 487 "setipargs=setenv bootargs root=${rootdev} rw " \ 488 "nfsroot=${serverip}:${rootpath} " \ 489 "ip=${ipaddr}:${serverip}:${gatewayip}:" \ 490 "${netmask}:${hostname}:${netdev}:off " \ 491 "console=${console},${baudrate} ${othbootargs}\0" \ 492 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 493 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ 494 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ 495 "\0" 496 497 #define CONFIG_NFSBOOTCOMMAND \ 498 "setenv rootdev /dev/nfs;" \ 499 "run setipargs;run addmtd;" \ 500 "tftp ${loadaddr} ${bootfile};" \ 501 "tftp ${fdtaddr} ${fdtfile};" \ 502 "fdt addr ${fdtaddr};" \ 503 "bootm ${loadaddr} - ${fdtaddr}" 504 505 /* UBI Support */ 506 #define CONFIG_MTD_PARTITIONS 507 508 #endif /* __CONFIG_H */ 509