xref: /openbmc/u-boot/include/configs/ids8313.h (revision 70341e2e)
1 /*
2  * (C) Copyright 2013
3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
4  *
5  * Based on:
6  * Copyright (c) 2011 IDS GmbH, Germany
7  * Sergej Stepanov <ste@ids.de>
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #ifndef __CONFIG_H
13 #define __CONFIG_H
14 
15 /*
16  * High Level Configuration Options
17  */
18 #define CONFIG_MPC831x
19 #define CONFIG_MPC8313
20 #define CONFIG_IDS8313
21 
22 
23 #define CONFIG_FSL_ELBC
24 
25 #define CONFIG_MISC_INIT_R
26 
27 #define CONFIG_BOOT_RETRY_TIME		900
28 #define CONFIG_BOOT_RETRY_MIN		30
29 #define CONFIG_BOOTDELAY		1
30 #define CONFIG_RESET_TO_RETRY
31 
32 #define CONFIG_83XX_CLKIN		66000000	/* in Hz */
33 #define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
34 
35 #define CONFIG_SYS_IMMR		0xF0000000
36 
37 #define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
38 #define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
39 
40 /*
41  * Hardware Reset Configuration Word
42  * if CLKIN is 66.000MHz, then
43  * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
44  */
45 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
46 			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
47 			     HRCWL_CSB_TO_CLKIN_2X1 |\
48 			     HRCWL_CORE_TO_CSB_2X1)
49 
50 #define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
51 				 HRCWH_CORE_ENABLE |\
52 				 HRCWH_FROM_0XFFF00100 |\
53 				 HRCWH_BOOTSEQ_DISABLE |\
54 				 HRCWH_SW_WATCHDOG_DISABLE |\
55 				 HRCWH_ROM_LOC_LOCAL_8BIT |\
56 				 HRCWH_RL_EXT_LEGACY |\
57 				 HRCWH_TSEC1M_IN_MII |\
58 				 HRCWH_TSEC2M_IN_MII |\
59 				 HRCWH_BIG_ENDIAN)
60 
61 #define CONFIG_SYS_SICRH	0x00000000
62 #define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
63 
64 #define CONFIG_HWCONFIG
65 
66 #define CONFIG_SYS_HID0_INIT	0x000000000
67 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
68 				 HID0_ENABLE_INSTRUCTION_CACHE |\
69 				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
70 
71 #define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
72 
73 /*
74  * Definitions for initial stack pointer and data area (in DCACHE )
75  */
76 #define CONFIG_SYS_INIT_RAM_LOCK
77 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
78 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
79 #define CONFIG_SYS_GBL_DATA_SIZE	0x100
80 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
81 					 - CONFIG_SYS_GBL_DATA_SIZE)
82 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
83 
84 /*
85  * Local Bus LCRR and LBCR regs
86  */
87 #define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
88 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
89 #define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
90 					 (0xFF << LBCR_BMT_SHIFT) |\
91 					 0xF)
92 
93 #define CONFIG_SYS_LBC_MRTPR		0x20000000
94 
95 /*
96  * Internal Definitions
97  */
98 /*
99  * DDR Setup
100  */
101 #define CONFIG_SYS_DDR_BASE		0x00000000
102 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
103 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
104 
105 /*
106  * Manually set up DDR parameters,
107  * as this board has not the SPD connected to I2C.
108  */
109 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
110 #define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
111 					 0x00010000 |\
112 					 CSCONFIG_ROW_BIT_13 |\
113 					 CSCONFIG_COL_BIT_10)
114 
115 #define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
116 					 CSCONFIG_BANK_BIT_3)
117 
118 #define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
119 #define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
120 				(3 << TIMING_CFG0_WRT_SHIFT) |\
121 				(3 << TIMING_CFG0_RRT_SHIFT) |\
122 				(3 << TIMING_CFG0_WWT_SHIFT) |\
123 				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
124 				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
125 				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
126 				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
127 #define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
128 				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
129 				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
130 				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
131 				(4 << TIMING_CFG1_REFREC_SHIFT) |\
132 				(4 << TIMING_CFG1_WRREC_SHIFT) |\
133 				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
134 				(2 << TIMING_CFG1_WRTORD_SHIFT))
135 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
136 				(5 << TIMING_CFG2_CPO_SHIFT) |\
137 				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
138 				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
139 				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
140 				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
141 				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
142 
143 #define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
144 				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
145 
146 #define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
147 					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
148 					 SDRAM_CFG_DBW_32 |\
149 					 SDRAM_CFG_SDRAM_TYPE_DDR2)
150 
151 #define CONFIG_SYS_SDRAM_CFG2		0x00401000
152 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
153 					 (0x0242 << SDRAM_MODE_SD_SHIFT))
154 #define CONFIG_SYS_DDR_MODE_2		0x00000000
155 #define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
156 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
157 					 DDRCDR_PZ_NOMZ |\
158 					 DDRCDR_NZ_NOMZ |\
159 					 DDRCDR_ODT |\
160 					 DDRCDR_M_ODR |\
161 					 DDRCDR_Q_DRN)
162 
163 /*
164  * on-board devices
165  */
166 #define CONFIG_TSEC1
167 #define CONFIG_TSEC2
168 #define CONFIG_TSEC_ENET
169 #define CONFIG_HARD_SPI
170 #define CONFIG_HARD_I2C
171 
172 /*
173  * NOR FLASH setup
174  */
175 #define CONFIG_SYS_FLASH_CFI
176 #define CONFIG_FLASH_CFI_DRIVER
177 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
178 #define CONFIG_FLASH_SHOW_PROGRESS	50
179 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
180 
181 #define CONFIG_SYS_FLASH_BASE		0xFF800000
182 #define CONFIG_SYS_FLASH_SIZE		8
183 #define CONFIG_SYS_FLASH_PROTECTION
184 
185 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
186 #define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
187 
188 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
189 					 BR_PS_8 |\
190 					 BR_MS_GPCM |\
191 					 BR_V)
192 
193 #define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
194 					 OR_GPCM_SCY_10 |\
195 					 OR_GPCM_EHTR |\
196 					 OR_GPCM_TRLX |\
197 					 OR_GPCM_CSNT |\
198 					 OR_GPCM_EAD)
199 #define CONFIG_SYS_MAX_FLASH_BANKS	1
200 #define CONFIG_SYS_MAX_FLASH_SECT	128
201 
202 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000
203 #define CONFIG_SYS_FLASH_WRITE_TOUT	500
204 
205 /*
206  * NAND FLASH setup
207  */
208 #define CONFIG_SYS_NAND_BASE		0xE1000000
209 #define CONFIG_SYS_MAX_NAND_DEVICE	1
210 #define CONFIG_SYS_NAND_MAX_CHIPS	1
211 #define CONFIG_NAND_FSL_ELBC
212 #define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
213 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
214 #define NAND_CACHE_PAGES		64
215 
216 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
217 #define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
218 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
219 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
220 
221 #define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
222 				 (2<<BR_DECC_SHIFT) |\
223 				 BR_PS_8 |\
224 				 BR_MS_FCM |\
225 				 BR_V)
226 
227 #define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
228 				 OR_FCM_PGS |\
229 				 OR_FCM_CSCT |\
230 				 OR_FCM_CST |\
231 				 OR_FCM_CHT |\
232 				 OR_FCM_SCY_4 |\
233 				 OR_FCM_TRLX |\
234 				 OR_FCM_EHTR |\
235 				 OR_FCM_RST)
236 
237 /*
238  * MRAM setup
239  */
240 #define CONFIG_SYS_MRAM_BASE		0xE2000000
241 #define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
242 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
243 #define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
244 
245 #define CONFIG_SYS_OR_TIMING_MRAM
246 
247 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
248 					 BR_PS_8 |\
249 					 BR_MS_GPCM |\
250 					 BR_V)
251 
252 #define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
253 
254 /*
255  * CPLD setup
256  */
257 #define CONFIG_SYS_CPLD_BASE		0xE3000000
258 #define CONFIG_SYS_CPLD_SIZE		0x8000
259 #define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
260 #define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
261 
262 #define CONFIG_SYS_OR_TIMING_MRAM
263 
264 #define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
265 					 BR_PS_8 |\
266 					 BR_MS_GPCM |\
267 					 BR_V)
268 
269 #define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
270 
271 /*
272  * HW-Watchdog
273  */
274 #define CONFIG_WATCHDOG		1
275 #define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
276 
277 /*
278  * I2C setup
279  */
280 #define CONFIG_CMD_I2C
281 #define CONFIG_SYS_I2C
282 #define CONFIG_SYS_I2C_FSL
283 #define CONFIG_SYS_FSL_I2C_SPEED	400000
284 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
285 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
286 #define CONFIG_RTC_PCF8563
287 #define CONFIG_SYS_I2C_RTC_ADDR	0x51
288 
289 /*
290  * SPI setup
291  */
292 #ifdef CONFIG_HARD_SPI
293 #define CONFIG_MPC8XXX_SPI
294 #define CONFIG_CMD_SPI
295 #define CONFIG_SYS_GPIO1_PRELIM
296 #define CONFIG_SYS_GPIO1_DIR		0x00000001
297 #define CONFIG_SYS_GPIO1_DAT		0x00000001
298 #endif
299 
300 /*
301  * Ethernet setup
302  */
303 #ifdef CONFIG_TSEC1
304 #define CONFIG_HAS_ETH0
305 #define CONFIG_TSEC1_NAME		"TSEC0"
306 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
307 #define TSEC1_PHY_ADDR			0x1
308 #define TSEC1_FLAGS			TSEC_GIGABIT
309 #define TSEC1_PHYIDX			0
310 #endif
311 
312 #ifdef CONFIG_TSEC2
313 #define CONFIG_HAS_ETH1
314 #define CONFIG_TSEC2_NAME		"TSEC1"
315 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
316 #define TSEC2_PHY_ADDR			0x3
317 #define TSEC2_FLAGS			TSEC_GIGABIT
318 #define TSEC2_PHYIDX			0
319 #endif
320 #define CONFIG_ETHPRIME		"TSEC1"
321 
322 /*
323  * Serial Port
324  */
325 #define CONFIG_CONS_INDEX		1
326 #define CONFIG_SYS_NS16550_SERIAL
327 #define CONFIG_SYS_NS16550_REG_SIZE	1
328 
329 #define CONFIG_SYS_BAUDRATE_TABLE	\
330 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
331 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
332 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
333 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
334 
335 #define CONFIG_HAS_FSL_DR_USB
336 #define CONFIG_SYS_SCCR_USBDRCM	3
337 
338 /*
339  * BAT's
340  */
341 #define CONFIG_HIGH_BATS
342 
343 /* DDR @ 0x00000000 */
344 #define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
345 					 BATL_PP_10)
346 #define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
347 					 BATU_BL_256M |\
348 					 BATU_VS |\
349 					 BATU_VP)
350 #define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
351 #define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
352 
353 /* Initial RAM @ 0xFD000000 */
354 #define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
355 					 BATL_PP_10 |\
356 					 BATL_GUARDEDSTORAGE)
357 #define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
358 					 BATU_BL_256K |\
359 					 BATU_VS |\
360 					 BATU_VP)
361 #define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
362 #define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
363 
364 /* FLASH @ 0xFF800000 */
365 #define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
366 					 BATL_PP_10 |\
367 					 BATL_GUARDEDSTORAGE)
368 #define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
369 					 BATU_BL_8M |\
370 					 BATU_VS |\
371 					 BATU_VP)
372 #define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
373 					 BATL_PP_10 |\
374 					 BATL_CACHEINHIBIT |\
375 					 BATL_GUARDEDSTORAGE)
376 #define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
377 
378 #define CONFIG_SYS_IBAT3L		(0)
379 #define CONFIG_SYS_IBAT3U		(0)
380 #define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
381 #define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
382 
383 #define CONFIG_SYS_IBAT4L		(0)
384 #define CONFIG_SYS_IBAT4U		(0)
385 #define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
386 #define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
387 
388 /* IMMRBAR @ 0xF0000000 */
389 #define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
390 					 BATL_PP_10 |\
391 					 BATL_CACHEINHIBIT |\
392 					 BATL_GUARDEDSTORAGE)
393 #define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
394 					 BATU_BL_128M |\
395 					 BATU_VS |\
396 					 BATU_VP)
397 #define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
398 #define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
399 
400 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
401 #define CONFIG_SYS_IBAT6L		(0xE0000000 |\
402 					 BATL_PP_10 |\
403 					 BATL_GUARDEDSTORAGE)
404 #define CONFIG_SYS_IBAT6U		(0xE0000000 |\
405 					 BATU_BL_256M |\
406 					 BATU_VS |\
407 					 BATU_VP)
408 #define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
409 #define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
410 
411 #define CONFIG_SYS_IBAT7L		(0)
412 #define CONFIG_SYS_IBAT7U		(0)
413 #define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
414 #define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
415 
416 /*
417  * U-Boot environment setup
418  */
419 #define CONFIG_CMD_DHCP
420 #define CONFIG_CMD_PING
421 #define CONFIG_CMD_NAND
422 #define CONFIG_CMD_SNTP
423 #define CONFIG_CMD_MII
424 #define CONFIG_CMD_DATE
425 #define CONFIG_CMDLINE_EDITING
426 #define CONFIG_CMD_JFFS2
427 #define CONFIG_BOOTP_SUBNETMASK
428 #define CONFIG_BOOTP_GATEWAY
429 #define CONFIG_BOOTP_HOSTNAME
430 #define CONFIG_BOOTP_BOOTPATH
431 #define CONFIG_BOOTP_BOOTFILESIZE
432 /* pass open firmware flat tree */
433 #define CONFIG_OF_LIBFDT
434 #define CONFIG_OF_BOARD_SETUP
435 #define CONFIG_OF_STDOUT_VIA_ALIAS
436 
437 /*
438  * The reserved memory
439  */
440 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
441 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
442 #define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
443 
444 /*
445  * Environment Configuration
446  */
447 #define CONFIG_ENV_IS_IN_FLASH
448 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
449 				+ CONFIG_SYS_MONITOR_LEN)
450 #define CONFIG_ENV_SIZE		0x20000
451 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
452 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
453 
454 
455 #define CONFIG_NETDEV			eth1
456 #define CONFIG_HOSTNAME		ids8313
457 #define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
458 #define CONFIG_BOOTFILE		"ids8313/uImage"
459 #define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
460 #define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
461 #define CONFIG_LOADADDR		0x400000
462 #define CONFIG_CMD_ENV_FLAGS
463 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
464 
465 #define CONFIG_BAUDRATE		115200
466 
467 /* Initial Memory map for Linux*/
468 #define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
469 
470 /*
471  * Miscellaneous configurable options
472  */
473 #define CONFIG_SYS_LONGHELP
474 #define CONFIG_SYS_CBSIZE		1024
475 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
476 					 + sizeof(CONFIG_SYS_PROMPT)+16)
477 #define CONFIG_SYS_MAXARGS		16
478 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
479 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
480 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
481 
482 #define CONFIG_SYS_MEMTEST_START	0x00001000
483 #define CONFIG_SYS_MEMTEST_END		0x00C00000
484 
485 #define CONFIG_SYS_LOAD_ADDR		0x100000
486 #define CONFIG_MII
487 #define CONFIG_LOADS_ECHO
488 #define CONFIG_TIMESTAMP
489 #define CONFIG_PREBOOT			"echo;" \
490 					"echo Type \\\"run nfsboot\\\" " \
491 					"to mount root filesystem over NFS;echo"
492 #undef	CONFIG_BOOTARGS
493 #define CONFIG_BOOTCOMMAND		"run boot_cramfs"
494 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE
495 
496 #define CONFIG_JFFS2_NAND
497 #define CONFIG_JFFS2_DEV		"0"
498 
499 /* mtdparts command line support */
500 #define CONFIG_CMD_MTDPARTS
501 #define CONFIG_FLASH_CFI_MTD
502 #define CONFIG_MTD_DEVICE
503 #define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
504 #define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
505 					"768k(BOOT-BIN)," \
506 					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
507 					"e1000000.flash:-(ubi)"
508 
509 #define CONFIG_EXTRA_ENV_SETTINGS \
510 	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
511 	"ethprime=TSEC1\0"						\
512 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
513 	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
514 		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
515 		" +${filesize}; "					\
516 		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
517 		" +${filesize}; "					\
518 		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
519 		" ${filesize}; "					\
520 		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
521 		" +${filesize}; "					\
522 		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
523 		" ${filesize}\0"					\
524 	"console=ttyS0\0"						\
525 	"fdtaddr=0x780000\0"						\
526 	"kernel_addr=ff800000\0"					\
527 	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
528 	"setbootargs=setenv bootargs "					\
529 		"root=${rootdev} rw console=${console},"		\
530 			"${baudrate} ${othbootargs}\0"			\
531 	"setipargs=setenv bootargs root=${rootdev} rw "			\
532 			"nfsroot=${serverip}:${rootpath} "		\
533 			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
534 			"${netmask}:${hostname}:${netdev}:off "		\
535 			"console=${console},${baudrate} ${othbootargs}\0" \
536 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
537 	"mtdids=" MTDIDS_DEFAULT "\0"					\
538 	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
539 	"\0"
540 
541 #define CONFIG_NFSBOOTCOMMAND						\
542 	"setenv rootdev /dev/nfs;"					\
543 	"run setipargs;run addmtd;"					\
544 	"tftp ${loadaddr} ${bootfile};"				\
545 	"tftp ${fdtaddr} ${fdtfile};"					\
546 	"fdt addr ${fdtaddr};"						\
547 	"bootm ${loadaddr} - ${fdtaddr}"
548 
549 /* UBI Support */
550 #define CONFIG_CMD_NAND_TRIMFFS
551 #define CONFIG_CMD_UBI
552 #define CONFIG_CMD_UBIFS
553 #define CONFIG_RBTREE
554 #define CONFIG_LZO
555 #define CONFIG_MTD_PARTITIONS
556 
557 /* bootcount support */
558 #define CONFIG_BOOTCOUNT_LIMIT
559 #define CONFIG_BOOTCOUNT_I2C
560 #define CONFIG_BOOTCOUNT_ALEN	1
561 #define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
562 
563 #define CONFIG_VERSION_VARIABLE
564 
565 #define CONFIG_IMAGE_FORMAT_LEGACY
566 #define CONFIG_CMD_FDT
567 #define CONFIG_CMD_HASH
568 #define CONFIG_SHA1
569 #define CONFIG_SHA256
570 
571 #endif	/* __CONFIG_H */
572