1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2013 4 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * 6 * Based on: 7 * Copyright (c) 2011 IDS GmbH, Germany 8 * Sergej Stepanov <ste@ids.de> 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* 15 * High Level Configuration Options 16 */ 17 #define CONFIG_MPC831x 18 #define CONFIG_MPC8313 19 20 #define CONFIG_FSL_ELBC 21 22 #define CONFIG_BOOT_RETRY_TIME 900 23 #define CONFIG_BOOT_RETRY_MIN 30 24 #define CONFIG_RESET_TO_RETRY 25 26 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 27 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 28 29 #define CONFIG_SYS_IMMR 0xF0000000 30 31 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 32 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 33 34 /* 35 * Hardware Reset Configuration Word 36 * if CLKIN is 66.000MHz, then 37 * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz 38 */ 39 #define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\ 40 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 41 HRCWL_CSB_TO_CLKIN_2X1 |\ 42 HRCWL_CORE_TO_CSB_2X1) 43 44 #define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\ 45 HRCWH_CORE_ENABLE |\ 46 HRCWH_FROM_0XFFF00100 |\ 47 HRCWH_BOOTSEQ_DISABLE |\ 48 HRCWH_SW_WATCHDOG_DISABLE |\ 49 HRCWH_ROM_LOC_LOCAL_8BIT |\ 50 HRCWH_RL_EXT_LEGACY |\ 51 HRCWH_TSEC1M_IN_MII |\ 52 HRCWH_TSEC2M_IN_MII |\ 53 HRCWH_BIG_ENDIAN) 54 55 #define CONFIG_SYS_SICRH 0x00000000 56 #define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D) 57 58 #define CONFIG_HWCONFIG 59 60 #define CONFIG_SYS_HID0_INIT 0x000000000 61 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\ 62 HID0_ENABLE_INSTRUCTION_CACHE |\ 63 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT) 64 65 #define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000) 66 67 /* 68 * Definitions for initial stack pointer and data area (in DCACHE ) 69 */ 70 #define CONFIG_SYS_INIT_RAM_LOCK 71 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 72 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */ 73 #define CONFIG_SYS_GBL_DATA_SIZE 0x100 74 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ 75 - CONFIG_SYS_GBL_DATA_SIZE) 76 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 77 78 /* 79 * Local Bus LCRR and LBCR regs 80 */ 81 #define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 82 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 83 #define CONFIG_SYS_LBC_LBCR (0x00040000 |\ 84 (0xFF << LBCR_BMT_SHIFT) |\ 85 0xF) 86 87 #define CONFIG_SYS_LBC_MRTPR 0x20000000 88 89 /* 90 * Internal Definitions 91 */ 92 /* 93 * DDR Setup 94 */ 95 #define CONFIG_SYS_DDR_BASE 0x00000000 96 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 97 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 98 99 /* 100 * Manually set up DDR parameters, 101 * as this board has not the SPD connected to I2C. 102 */ 103 #define CONFIG_SYS_DDR_SIZE 256 /* MB */ 104 #define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\ 105 0x00010000 |\ 106 CSCONFIG_ROW_BIT_13 |\ 107 CSCONFIG_COL_BIT_10) 108 109 #define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \ 110 CSCONFIG_BANK_BIT_3) 111 112 #define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */ 113 #define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\ 114 (3 << TIMING_CFG0_WRT_SHIFT) |\ 115 (3 << TIMING_CFG0_RRT_SHIFT) |\ 116 (3 << TIMING_CFG0_WWT_SHIFT) |\ 117 (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\ 118 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\ 119 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ 120 (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 121 #define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\ 122 (12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\ 123 (4 << TIMING_CFG1_ACTTORW_SHIFT) |\ 124 (7 << TIMING_CFG1_CASLAT_SHIFT) |\ 125 (4 << TIMING_CFG1_REFREC_SHIFT) |\ 126 (4 << TIMING_CFG1_WRREC_SHIFT) |\ 127 (2 << TIMING_CFG1_ACTTOACT_SHIFT) |\ 128 (2 << TIMING_CFG1_WRTORD_SHIFT)) 129 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\ 130 (5 << TIMING_CFG2_CPO_SHIFT) |\ 131 (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\ 132 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\ 133 (0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\ 134 (1 << TIMING_CFG2_CKE_PLS_SHIFT) |\ 135 (6 << TIMING_CFG2_FOUR_ACT_SHIFT)) 136 137 #define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\ 138 (0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 139 140 #define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\ 141 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\ 142 SDRAM_CFG_DBW_32 |\ 143 SDRAM_CFG_SDRAM_TYPE_DDR2) 144 145 #define CONFIG_SYS_SDRAM_CFG2 0x00401000 146 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\ 147 (0x0242 << SDRAM_MODE_SD_SHIFT)) 148 #define CONFIG_SYS_DDR_MODE_2 0x00000000 149 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075 150 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\ 151 DDRCDR_PZ_NOMZ |\ 152 DDRCDR_NZ_NOMZ |\ 153 DDRCDR_ODT |\ 154 DDRCDR_M_ODR |\ 155 DDRCDR_Q_DRN) 156 157 /* 158 * on-board devices 159 */ 160 #define CONFIG_TSEC1 161 #define CONFIG_TSEC2 162 163 /* 164 * NOR FLASH setup 165 */ 166 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT 167 #define CONFIG_FLASH_SHOW_PROGRESS 50 168 169 #define CONFIG_SYS_FLASH_BASE 0xFF800000 170 #define CONFIG_SYS_FLASH_SIZE 8 171 172 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 173 #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 174 175 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\ 176 BR_PS_8 |\ 177 BR_MS_GPCM |\ 178 BR_V) 179 180 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ 181 OR_GPCM_SCY_10 |\ 182 OR_GPCM_EHTR |\ 183 OR_GPCM_TRLX |\ 184 OR_GPCM_CSNT |\ 185 OR_GPCM_EAD) 186 #define CONFIG_SYS_MAX_FLASH_BANKS 1 187 #define CONFIG_SYS_MAX_FLASH_SECT 128 188 189 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 190 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 191 192 /* 193 * NAND FLASH setup 194 */ 195 #define CONFIG_SYS_NAND_BASE 0xE1000000 196 #define CONFIG_SYS_MAX_NAND_DEVICE 1 197 #define CONFIG_SYS_NAND_MAX_CHIPS 1 198 #define CONFIG_NAND_FSL_ELBC 199 #define CONFIG_SYS_NAND_PAGE_SIZE (2048) 200 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) 201 #define NAND_CACHE_PAGES 64 202 203 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 204 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E 205 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 206 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 207 208 #define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\ 209 (2<<BR_DECC_SHIFT) |\ 210 BR_PS_8 |\ 211 BR_MS_FCM |\ 212 BR_V) 213 214 #define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\ 215 OR_FCM_PGS |\ 216 OR_FCM_CSCT |\ 217 OR_FCM_CST |\ 218 OR_FCM_CHT |\ 219 OR_FCM_SCY_4 |\ 220 OR_FCM_TRLX |\ 221 OR_FCM_EHTR |\ 222 OR_FCM_RST) 223 224 /* 225 * MRAM setup 226 */ 227 #define CONFIG_SYS_MRAM_BASE 0xE2000000 228 #define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */ 229 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE 230 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */ 231 232 #define CONFIG_SYS_OR_TIMING_MRAM 233 234 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\ 235 BR_PS_8 |\ 236 BR_MS_GPCM |\ 237 BR_V) 238 239 #define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74 240 241 /* 242 * CPLD setup 243 */ 244 #define CONFIG_SYS_CPLD_BASE 0xE3000000 245 #define CONFIG_SYS_CPLD_SIZE 0x8000 246 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE 247 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E 248 249 #define CONFIG_SYS_OR_TIMING_MRAM 250 251 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\ 252 BR_PS_8 |\ 253 BR_MS_GPCM |\ 254 BR_V) 255 256 #define CONFIG_SYS_OR3_PRELIM 0xFFFF8814 257 258 /* 259 * HW-Watchdog 260 */ 261 #define CONFIG_WATCHDOG 1 262 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF 263 264 /* 265 * I2C setup 266 */ 267 #define CONFIG_SYS_I2C 268 #define CONFIG_SYS_I2C_FSL 269 #define CONFIG_SYS_FSL_I2C_SPEED 400000 270 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 271 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 272 #define CONFIG_RTC_PCF8563 273 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 274 275 /* 276 * Ethernet setup 277 */ 278 #ifdef CONFIG_TSEC1 279 #define CONFIG_HAS_ETH0 280 #define CONFIG_TSEC1_NAME "TSEC0" 281 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 282 #define TSEC1_PHY_ADDR 0x1 283 #define TSEC1_FLAGS TSEC_GIGABIT 284 #define TSEC1_PHYIDX 0 285 #endif 286 287 #ifdef CONFIG_TSEC2 288 #define CONFIG_HAS_ETH1 289 #define CONFIG_TSEC2_NAME "TSEC1" 290 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 291 #define TSEC2_PHY_ADDR 0x3 292 #define TSEC2_FLAGS TSEC_GIGABIT 293 #define TSEC2_PHYIDX 0 294 #endif 295 #define CONFIG_ETHPRIME "TSEC1" 296 297 /* 298 * Serial Port 299 */ 300 #define CONFIG_SYS_NS16550_SERIAL 301 #define CONFIG_SYS_NS16550_REG_SIZE 1 302 303 #define CONFIG_SYS_BAUDRATE_TABLE \ 304 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 305 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 306 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 307 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) 308 309 #define CONFIG_HAS_FSL_DR_USB 310 #define CONFIG_SYS_SCCR_USBDRCM 3 311 312 /* 313 * BAT's 314 */ 315 #define CONFIG_HIGH_BATS 316 317 /* DDR @ 0x00000000 */ 318 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\ 319 BATL_PP_10) 320 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\ 321 BATU_BL_256M |\ 322 BATU_VS |\ 323 BATU_VP) 324 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 325 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 326 327 /* Initial RAM @ 0xFD000000 */ 328 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\ 329 BATL_PP_10 |\ 330 BATL_GUARDEDSTORAGE) 331 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\ 332 BATU_BL_256K |\ 333 BATU_VS |\ 334 BATU_VP) 335 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 336 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 337 338 /* FLASH @ 0xFF800000 */ 339 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\ 340 BATL_PP_10 |\ 341 BATL_GUARDEDSTORAGE) 342 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\ 343 BATU_BL_8M |\ 344 BATU_VS |\ 345 BATU_VP) 346 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\ 347 BATL_PP_10 |\ 348 BATL_CACHEINHIBIT |\ 349 BATL_GUARDEDSTORAGE) 350 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 351 352 #define CONFIG_SYS_IBAT3L (0) 353 #define CONFIG_SYS_IBAT3U (0) 354 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 355 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 356 357 #define CONFIG_SYS_IBAT4L (0) 358 #define CONFIG_SYS_IBAT4U (0) 359 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 360 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 361 362 /* IMMRBAR @ 0xF0000000 */ 363 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\ 364 BATL_PP_10 |\ 365 BATL_CACHEINHIBIT |\ 366 BATL_GUARDEDSTORAGE) 367 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\ 368 BATU_BL_128M |\ 369 BATU_VS |\ 370 BATU_VP) 371 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 372 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 373 374 /* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */ 375 #define CONFIG_SYS_IBAT6L (0xE0000000 |\ 376 BATL_PP_10 |\ 377 BATL_GUARDEDSTORAGE) 378 #define CONFIG_SYS_IBAT6U (0xE0000000 |\ 379 BATU_BL_256M |\ 380 BATU_VS |\ 381 BATU_VP) 382 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 383 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 384 385 #define CONFIG_SYS_IBAT7L (0) 386 #define CONFIG_SYS_IBAT7U (0) 387 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 388 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 389 390 /* 391 * U-Boot environment setup 392 */ 393 #define CONFIG_BOOTP_BOOTFILESIZE 394 395 /* 396 * The reserved memory 397 */ 398 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 399 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 400 #define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024) 401 402 /* 403 * Environment Configuration 404 */ 405 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 406 + CONFIG_SYS_MONITOR_LEN) 407 #define CONFIG_ENV_SIZE 0x20000 408 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) 409 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 410 411 #define CONFIG_NETDEV eth1 412 #define CONFIG_HOSTNAME "ids8313" 413 #define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx" 414 #define CONFIG_BOOTFILE "ids8313/uImage" 415 #define CONFIG_UBOOTPATH "ids8313/u-boot.bin" 416 #define CONFIG_FDTFILE "ids8313/ids8313.dtb" 417 #define CONFIG_LOADADDR 0x400000 418 #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo" 419 420 /* Initial Memory map for Linux*/ 421 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 422 423 /* 424 * Miscellaneous configurable options 425 */ 426 #define CONFIG_SYS_CBSIZE 1024 427 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 428 429 #define CONFIG_SYS_MEMTEST_START 0x00001000 430 #define CONFIG_SYS_MEMTEST_END 0x00C00000 431 432 #define CONFIG_SYS_LOAD_ADDR 0x100000 433 #define CONFIG_LOADS_ECHO 434 #define CONFIG_TIMESTAMP 435 #define CONFIG_PREBOOT "echo;" \ 436 "echo Type \\\"run nfsboot\\\" " \ 437 "to mount root filesystem over NFS;echo" 438 #define CONFIG_BOOTCOMMAND "run boot_cramfs" 439 #undef CONFIG_SYS_LOADS_BAUD_CHANGE 440 441 #define CONFIG_JFFS2_NAND 442 #define CONFIG_JFFS2_DEV "0" 443 444 /* mtdparts command line support */ 445 446 #define CONFIG_EXTRA_ENV_SETTINGS \ 447 "netdev=" __stringify(CONFIG_NETDEV) "\0" \ 448 "ethprime=TSEC1\0" \ 449 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 450 "tftpflash=tftpboot ${loadaddr} ${uboot}; " \ 451 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 452 " +${filesize}; " \ 453 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 454 " +${filesize}; " \ 455 "cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ 456 " ${filesize}; " \ 457 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 458 " +${filesize}; " \ 459 "cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \ 460 " ${filesize}\0" \ 461 "console=ttyS0\0" \ 462 "fdtaddr=0x780000\0" \ 463 "kernel_addr=ff800000\0" \ 464 "fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \ 465 "setbootargs=setenv bootargs " \ 466 "root=${rootdev} rw console=${console}," \ 467 "${baudrate} ${othbootargs}\0" \ 468 "setipargs=setenv bootargs root=${rootdev} rw " \ 469 "nfsroot=${serverip}:${rootpath} " \ 470 "ip=${ipaddr}:${serverip}:${gatewayip}:" \ 471 "${netmask}:${hostname}:${netdev}:off " \ 472 "console=${console},${baudrate} ${othbootargs}\0" \ 473 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 474 "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ 475 "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ 476 "\0" 477 478 #define CONFIG_NFSBOOTCOMMAND \ 479 "setenv rootdev /dev/nfs;" \ 480 "run setipargs;run addmtd;" \ 481 "tftp ${loadaddr} ${bootfile};" \ 482 "tftp ${fdtaddr} ${fdtfile};" \ 483 "fdt addr ${fdtaddr};" \ 484 "bootm ${loadaddr} - ${fdtaddr}" 485 486 /* UBI Support */ 487 488 #endif /* __CONFIG_H */ 489