1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2014 4 * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc 5 * 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 /* 12 * High Level Configuration Options 13 */ 14 #define CONFIG_E300 1 /* E300 family */ 15 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 16 #define CONFIG_MPC830x 1 /* MPC830x family */ 17 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 18 #define CONFIG_HRCON 1 /* HRCON board specific */ 19 20 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 21 22 /* 23 * System Clock Setup 24 */ 25 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 26 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 27 28 /* 29 * Hardware Reset Configuration Word 30 * if CLKIN is 66.66MHz, then 31 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 32 * We choose the A type silicon as default, so the core is 400Mhz. 33 */ 34 #define CONFIG_SYS_HRCW_LOW (\ 35 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 36 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 37 HRCWL_SVCOD_DIV_2 |\ 38 HRCWL_CSB_TO_CLKIN_4X1 |\ 39 HRCWL_CORE_TO_CSB_3X1) 40 /* 41 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 42 * in 8308's HRCWH according to the manual, but original Freescale's 43 * code has them and I've expirienced some problems using the board 44 * with BDI3000 attached when I've tried to set these bits to zero 45 * (UART doesn't work after the 'reset run' command). 46 */ 47 #define CONFIG_SYS_HRCW_HIGH (\ 48 HRCWH_PCI_HOST |\ 49 HRCWH_PCI1_ARBITER_ENABLE |\ 50 HRCWH_CORE_ENABLE |\ 51 HRCWH_FROM_0XFFF00100 |\ 52 HRCWH_BOOTSEQ_DISABLE |\ 53 HRCWH_SW_WATCHDOG_DISABLE |\ 54 HRCWH_ROM_LOC_LOCAL_16BIT |\ 55 HRCWH_RL_EXT_LEGACY |\ 56 HRCWH_TSEC1M_IN_RGMII |\ 57 HRCWH_TSEC2M_IN_RGMII |\ 58 HRCWH_BIG_ENDIAN) 59 60 /* 61 * System IO Config 62 */ 63 #define CONFIG_SYS_SICRH (\ 64 SICRH_ESDHC_A_SD |\ 65 SICRH_ESDHC_B_SD |\ 66 SICRH_ESDHC_C_SD |\ 67 SICRH_GPIO_A_GPIO |\ 68 SICRH_GPIO_B_GPIO |\ 69 SICRH_IEEE1588_A_GPIO |\ 70 SICRH_USB |\ 71 SICRH_GTM_GPIO |\ 72 SICRH_IEEE1588_B_GPIO |\ 73 SICRH_ETSEC2_GPIO |\ 74 SICRH_GPIOSEL_1 |\ 75 SICRH_TMROBI_V3P3 |\ 76 SICRH_TSOBI1_V2P5 |\ 77 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 78 #define CONFIG_SYS_SICRL (\ 79 SICRL_SPI_PF0 |\ 80 SICRL_UART_PF0 |\ 81 SICRL_IRQ_PF0 |\ 82 SICRL_I2C2_PF0 |\ 83 SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ 84 85 /* 86 * IMMR new address 87 */ 88 #define CONFIG_SYS_IMMR 0xE0000000 89 90 /* 91 * SERDES 92 */ 93 #define CONFIG_FSL_SERDES 94 #define CONFIG_FSL_SERDES1 0xe3000 95 96 /* 97 * Arbiter Setup 98 */ 99 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 100 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 101 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 102 103 /* 104 * DDR Setup 105 */ 106 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 107 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 108 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 109 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 110 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 111 | DDRCDR_PZ_LOZ \ 112 | DDRCDR_NZ_LOZ \ 113 | DDRCDR_ODT \ 114 | DDRCDR_Q_DRN) 115 /* 0x7b880001 */ 116 /* 117 * Manually set up DDR parameters 118 * consist of one chip NT5TU64M16HG from NANYA 119 */ 120 121 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 122 123 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 124 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 125 | CSCONFIG_ODT_RD_NEVER \ 126 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 127 | CSCONFIG_BANK_BIT_3 \ 128 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 129 /* 0x80010102 */ 130 #define CONFIG_SYS_DDR_TIMING_3 0 131 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 132 | (0 << TIMING_CFG0_WRT_SHIFT) \ 133 | (0 << TIMING_CFG0_RRT_SHIFT) \ 134 | (0 << TIMING_CFG0_WWT_SHIFT) \ 135 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 136 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 137 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 138 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 139 /* 0x00260802 */ 140 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 141 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 142 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 143 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 144 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 145 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 146 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 147 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 148 /* 0x26279222 */ 149 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 150 | (4 << TIMING_CFG2_CPO_SHIFT) \ 151 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 152 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 153 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 154 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 155 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 156 /* 0x021848c5 */ 157 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 158 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 159 /* 0x08240100 */ 160 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 161 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 162 | SDRAM_CFG_DBW_16) 163 /* 0x43100000 */ 164 165 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 166 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 167 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 168 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 169 #define CONFIG_SYS_DDR_MODE2 0x00000000 170 171 /* 172 * Memory test 173 */ 174 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 175 #define CONFIG_SYS_MEMTEST_END 0x07f00000 176 177 /* 178 * The reserved memory 179 */ 180 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 181 182 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 183 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 184 185 /* 186 * Initial RAM Base Address Setup 187 */ 188 #define CONFIG_SYS_INIT_RAM_LOCK 1 189 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 190 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 191 #define CONFIG_SYS_GBL_DATA_OFFSET \ 192 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 193 194 /* 195 * Local Bus Configuration & Clock Setup 196 */ 197 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 198 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 199 #define CONFIG_SYS_LBC_LBCR 0x00040000 200 201 /* 202 * FLASH on the Local Bus 203 */ 204 #if 1 205 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 206 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 207 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 208 #define CONFIG_FLASH_CFI_LEGACY 209 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 210 #endif 211 212 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 213 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 214 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 215 216 /* Window base at flash base */ 217 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 218 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 219 220 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 221 | BR_PS_16 /* 16 bit port */ \ 222 | BR_MS_GPCM /* MSEL = GPCM */ \ 223 | BR_V) /* valid */ 224 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 225 | OR_UPM_XAM \ 226 | OR_GPCM_CSNT \ 227 | OR_GPCM_ACS_DIV2 \ 228 | OR_GPCM_XACS \ 229 | OR_GPCM_SCY_15 \ 230 | OR_GPCM_TRLX_SET \ 231 | OR_GPCM_EHTR_SET) 232 233 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 234 #define CONFIG_SYS_MAX_FLASH_SECT 135 235 236 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 237 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 238 239 /* 240 * FPGA 241 */ 242 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 243 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 244 245 /* Window base at FPGA base */ 246 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 247 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 248 249 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 250 | BR_PS_16 /* 16 bit port */ \ 251 | BR_MS_GPCM /* MSEL = GPCM */ \ 252 | BR_V) /* valid */ 253 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 254 | OR_UPM_XAM \ 255 | OR_GPCM_CSNT \ 256 | OR_GPCM_ACS_DIV2 \ 257 | OR_GPCM_XACS \ 258 | OR_GPCM_SCY_15 \ 259 | OR_GPCM_TRLX_SET \ 260 | OR_GPCM_EHTR_SET) 261 262 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 263 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 264 265 #define CONFIG_SYS_FPGA_COUNT 1 266 267 #define CONFIG_SYS_MCLINK_MAX 3 268 269 #define CONFIG_SYS_FPGA_PTR \ 270 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 271 272 /* 273 * Serial Port 274 */ 275 #define CONFIG_SYS_NS16550_SERIAL 276 #define CONFIG_SYS_NS16550_REG_SIZE 1 277 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 278 279 #define CONFIG_SYS_BAUDRATE_TABLE \ 280 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 281 282 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 283 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 284 285 /* Pass open firmware flat tree */ 286 287 /* I2C */ 288 #define CONFIG_SYS_I2C 289 #define CONFIG_SYS_I2C_FSL 290 #define CONFIG_SYS_FSL_I2C_SPEED 400000 291 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 292 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 293 294 #define CONFIG_PCA953X /* NXP PCA9554 */ 295 #define CONFIG_PCA9698 /* NXP PCA9698 */ 296 297 #define CONFIG_SYS_I2C_IHS 298 #define CONFIG_SYS_I2C_IHS_CH0 299 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 300 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 301 #define CONFIG_SYS_I2C_IHS_CH1 302 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 303 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 304 #define CONFIG_SYS_I2C_IHS_CH2 305 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 306 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 307 #define CONFIG_SYS_I2C_IHS_CH3 308 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 309 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 310 311 #ifdef CONFIG_HRCON_DH 312 #define CONFIG_SYS_I2C_IHS_DUAL 313 #define CONFIG_SYS_I2C_IHS_CH0_1 314 #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 315 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F 316 #define CONFIG_SYS_I2C_IHS_CH1_1 317 #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 318 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F 319 #define CONFIG_SYS_I2C_IHS_CH2_1 320 #define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000 321 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F 322 #define CONFIG_SYS_I2C_IHS_CH3_1 323 #define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000 324 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F 325 #endif 326 327 /* 328 * Software (bit-bang) I2C driver configuration 329 */ 330 #define CONFIG_SYS_I2C_SOFT 331 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 332 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 333 #define I2C_SOFT_DECLARATIONS2 334 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 335 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 336 #define I2C_SOFT_DECLARATIONS3 337 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 338 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 339 #define I2C_SOFT_DECLARATIONS4 340 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 341 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 342 #define I2C_SOFT_DECLARATIONS5 343 #define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 344 #define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F 345 #define I2C_SOFT_DECLARATIONS6 346 #define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 347 #define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F 348 #define I2C_SOFT_DECLARATIONS7 349 #define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 350 #define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F 351 #define I2C_SOFT_DECLARATIONS8 352 #define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 353 #define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F 354 355 #ifdef CONFIG_HRCON_DH 356 #define I2C_SOFT_DECLARATIONS9 357 #define CONFIG_SYS_I2C_SOFT_SPEED_9 50000 358 #define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F 359 #define I2C_SOFT_DECLARATIONS10 360 #define CONFIG_SYS_I2C_SOFT_SPEED_10 50000 361 #define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F 362 #define I2C_SOFT_DECLARATIONS11 363 #define CONFIG_SYS_I2C_SOFT_SPEED_11 50000 364 #define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F 365 #define I2C_SOFT_DECLARATIONS12 366 #define CONFIG_SYS_I2C_SOFT_SPEED_12 50000 367 #define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F 368 #endif 369 370 #ifdef CONFIG_HRCON_DH 371 #define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20} 372 #define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8} 373 #define CONFIG_HRCON_FANS { {10, 0x4c}, {11, 0x4c}, \ 374 {12, 0x4c} } 375 #else 376 #define CONFIG_SYS_ICS8N3QV01_I2C {9, 10, 11, 12} 377 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 378 #define CONFIG_HRCON_FANS { {6, 0x4c}, {7, 0x4c}, \ 379 {8, 0x4c} } 380 #endif 381 382 #ifndef __ASSEMBLY__ 383 void fpga_gpio_set(unsigned int bus, int pin); 384 void fpga_gpio_clear(unsigned int bus, int pin); 385 int fpga_gpio_get(unsigned int bus, int pin); 386 void fpga_control_set(unsigned int bus, int pin); 387 void fpga_control_clear(unsigned int bus, int pin); 388 #endif 389 390 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200) 391 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100) 392 #define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4) 393 394 #ifdef CONFIG_HRCON_DH 395 #define I2C_ACTIVE \ 396 do { \ 397 if (I2C_ADAP_HWNR > 7) \ 398 fpga_control_set(I2C_FPGA_IDX, 0x0004); \ 399 else \ 400 fpga_control_clear(I2C_FPGA_IDX, 0x0004); \ 401 } while (0) 402 #else 403 #define I2C_ACTIVE { } 404 #endif 405 #define I2C_TRISTATE { } 406 #define I2C_READ \ 407 (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) 408 #define I2C_SDA(bit) \ 409 do { \ 410 if (bit) \ 411 fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 412 else \ 413 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 414 } while (0) 415 #define I2C_SCL(bit) \ 416 do { \ 417 if (bit) \ 418 fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 419 else \ 420 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 421 } while (0) 422 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 423 424 /* 425 * Software (bit-bang) MII driver configuration 426 */ 427 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 428 #define CONFIG_BITBANGMII_MULTI 429 430 /* 431 * OSD Setup 432 */ 433 #define CONFIG_SYS_OSD_SCREENS 1 434 #define CONFIG_SYS_DP501_DIFFERENTIAL 435 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 436 437 #ifdef CONFIG_HRCON_DH 438 #define CONFIG_SYS_OSD_DH 439 #endif 440 441 /* 442 * General PCI 443 * Addresses are mapped 1-1. 444 */ 445 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 446 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 447 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 448 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 449 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 450 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 451 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 452 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 453 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 454 455 /* enable PCIE clock */ 456 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 457 458 #define CONFIG_PCI_INDIRECT_BRIDGE 459 #define CONFIG_PCIE 460 461 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 462 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 463 464 /* 465 * TSEC 466 */ 467 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 468 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 469 470 /* 471 * TSEC ethernet configuration 472 */ 473 #define CONFIG_TSEC1 474 #define CONFIG_TSEC1_NAME "eTSEC0" 475 #define TSEC1_PHY_ADDR 1 476 #define TSEC1_PHYIDX 0 477 #define TSEC1_FLAGS TSEC_GIGABIT 478 479 /* Options are: eTSEC[0-1] */ 480 #define CONFIG_ETHPRIME "eTSEC0" 481 482 /* 483 * Environment 484 */ 485 #if 1 486 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 487 CONFIG_SYS_MONITOR_LEN) 488 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 489 #define CONFIG_ENV_SIZE 0x2000 490 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 491 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 492 #else 493 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 494 #endif 495 496 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 497 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 498 499 /* 500 * Command line configuration. 501 */ 502 503 /* 504 * Miscellaneous configurable options 505 */ 506 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 507 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 508 509 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 510 511 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 512 513 /* 514 * For booting Linux, the board info and command line data 515 * have to be in the first 256 MB of memory, since this is 516 * the maximum mapped by the Linux kernel during initialization. 517 */ 518 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 519 520 /* 521 * Core HID Setup 522 */ 523 #define CONFIG_SYS_HID0_INIT 0x000000000 524 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 525 HID0_ENABLE_INSTRUCTION_CACHE | \ 526 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 527 #define CONFIG_SYS_HID2 HID2_HBE 528 529 /* 530 * MMU Setup 531 */ 532 533 /* DDR: cache cacheable */ 534 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 535 BATL_MEMCOHERENCE) 536 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 537 BATU_VS | BATU_VP) 538 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 539 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 540 541 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 542 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 543 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 544 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 545 BATU_VP) 546 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 547 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 548 549 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 550 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 551 BATL_MEMCOHERENCE) 552 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 553 BATU_VS | BATU_VP) 554 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 555 BATL_CACHEINHIBIT | \ 556 BATL_GUARDEDSTORAGE) 557 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 558 559 /* Stack in dcache: cacheable, no memory coherence */ 560 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 561 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 562 BATU_VS | BATU_VP) 563 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 564 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 565 566 /* 567 * Environment Configuration 568 */ 569 570 #define CONFIG_ENV_OVERWRITE 571 572 #if defined(CONFIG_TSEC_ENET) 573 #define CONFIG_HAS_ETH0 574 #endif 575 576 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 577 578 579 #define CONFIG_HOSTNAME "hrcon" 580 #define CONFIG_ROOTPATH "/opt/nfsroot" 581 #define CONFIG_BOOTFILE "uImage" 582 583 #define CONFIG_PREBOOT /* enable preboot variable */ 584 585 #define CONFIG_EXTRA_ENV_SETTINGS \ 586 "netdev=eth0\0" \ 587 "consoledev=ttyS1\0" \ 588 "u-boot=u-boot.bin\0" \ 589 "kernel_addr=1000000\0" \ 590 "fdt_addr=C00000\0" \ 591 "fdtfile=hrcon.dtb\0" \ 592 "load=tftp ${loadaddr} ${u-boot}\0" \ 593 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 594 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 595 " +${filesize};cp.b ${fileaddr} " \ 596 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 597 "upd=run load update\0" \ 598 599 #define CONFIG_NFSBOOTCOMMAND \ 600 "setenv bootargs root=/dev/nfs rw " \ 601 "nfsroot=$serverip:$rootpath " \ 602 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 603 "console=$consoledev,$baudrate $othbootargs;" \ 604 "tftp ${kernel_addr} $bootfile;" \ 605 "tftp ${fdt_addr} $fdtfile;" \ 606 "bootm ${kernel_addr} - ${fdt_addr}" 607 608 #define CONFIG_MMCBOOTCOMMAND \ 609 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 610 "console=$consoledev,$baudrate $othbootargs;" \ 611 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 612 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 613 "bootm ${kernel_addr} - ${fdt_addr}" 614 615 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 616 617 #endif /* __CONFIG_H */ 618