1 /* 2 * (C) Copyright 2014 3 * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_HRCON 1 /* HRCON board specific */ 20 21 #define CONFIG_SYS_TEXT_BASE 0xFE000000 22 23 #define CONFIG_BOARD_EARLY_INIT_R 24 #define CONFIG_LAST_STAGE_INIT 25 26 #define CONFIG_FSL_ESDHC 27 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 28 29 /* 30 * System Clock Setup 31 */ 32 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 33 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 34 35 /* 36 * Hardware Reset Configuration Word 37 * if CLKIN is 66.66MHz, then 38 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 39 * We choose the A type silicon as default, so the core is 400Mhz. 40 */ 41 #define CONFIG_SYS_HRCW_LOW (\ 42 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 43 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 44 HRCWL_SVCOD_DIV_2 |\ 45 HRCWL_CSB_TO_CLKIN_4X1 |\ 46 HRCWL_CORE_TO_CSB_3X1) 47 /* 48 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 49 * in 8308's HRCWH according to the manual, but original Freescale's 50 * code has them and I've expirienced some problems using the board 51 * with BDI3000 attached when I've tried to set these bits to zero 52 * (UART doesn't work after the 'reset run' command). 53 */ 54 #define CONFIG_SYS_HRCW_HIGH (\ 55 HRCWH_PCI_HOST |\ 56 HRCWH_PCI1_ARBITER_ENABLE |\ 57 HRCWH_CORE_ENABLE |\ 58 HRCWH_FROM_0XFFF00100 |\ 59 HRCWH_BOOTSEQ_DISABLE |\ 60 HRCWH_SW_WATCHDOG_DISABLE |\ 61 HRCWH_ROM_LOC_LOCAL_16BIT |\ 62 HRCWH_RL_EXT_LEGACY |\ 63 HRCWH_TSEC1M_IN_RGMII |\ 64 HRCWH_TSEC2M_IN_RGMII |\ 65 HRCWH_BIG_ENDIAN) 66 67 /* 68 * System IO Config 69 */ 70 #define CONFIG_SYS_SICRH (\ 71 SICRH_ESDHC_A_SD |\ 72 SICRH_ESDHC_B_SD |\ 73 SICRH_ESDHC_C_SD |\ 74 SICRH_GPIO_A_GPIO |\ 75 SICRH_GPIO_B_GPIO |\ 76 SICRH_IEEE1588_A_GPIO |\ 77 SICRH_USB |\ 78 SICRH_GTM_GPIO |\ 79 SICRH_IEEE1588_B_GPIO |\ 80 SICRH_ETSEC2_GPIO |\ 81 SICRH_GPIOSEL_1 |\ 82 SICRH_TMROBI_V3P3 |\ 83 SICRH_TSOBI1_V2P5 |\ 84 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 85 #define CONFIG_SYS_SICRL (\ 86 SICRL_SPI_PF0 |\ 87 SICRL_UART_PF0 |\ 88 SICRL_IRQ_PF0 |\ 89 SICRL_I2C2_PF0 |\ 90 SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ 91 92 /* 93 * IMMR new address 94 */ 95 #define CONFIG_SYS_IMMR 0xE0000000 96 97 /* 98 * SERDES 99 */ 100 #define CONFIG_FSL_SERDES 101 #define CONFIG_FSL_SERDES1 0xe3000 102 103 /* 104 * Arbiter Setup 105 */ 106 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 107 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 108 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 109 110 /* 111 * DDR Setup 112 */ 113 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 114 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 115 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 116 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 117 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 118 | DDRCDR_PZ_LOZ \ 119 | DDRCDR_NZ_LOZ \ 120 | DDRCDR_ODT \ 121 | DDRCDR_Q_DRN) 122 /* 0x7b880001 */ 123 /* 124 * Manually set up DDR parameters 125 * consist of one chip NT5TU64M16HG from NANYA 126 */ 127 128 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 129 130 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 131 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 132 | CSCONFIG_ODT_RD_NEVER \ 133 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 134 | CSCONFIG_BANK_BIT_3 \ 135 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 136 /* 0x80010102 */ 137 #define CONFIG_SYS_DDR_TIMING_3 0 138 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 139 | (0 << TIMING_CFG0_WRT_SHIFT) \ 140 | (0 << TIMING_CFG0_RRT_SHIFT) \ 141 | (0 << TIMING_CFG0_WWT_SHIFT) \ 142 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 143 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 144 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 145 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 146 /* 0x00260802 */ 147 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 148 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 149 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 150 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 151 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 152 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 153 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 154 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 155 /* 0x26279222 */ 156 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 157 | (4 << TIMING_CFG2_CPO_SHIFT) \ 158 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 159 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 160 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 161 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 162 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 163 /* 0x021848c5 */ 164 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 165 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 166 /* 0x08240100 */ 167 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 168 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 169 | SDRAM_CFG_DBW_16) 170 /* 0x43100000 */ 171 172 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 173 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 174 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 175 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 176 #define CONFIG_SYS_DDR_MODE2 0x00000000 177 178 /* 179 * Memory test 180 */ 181 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 182 #define CONFIG_SYS_MEMTEST_END 0x07f00000 183 184 /* 185 * The reserved memory 186 */ 187 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 188 189 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 190 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 191 192 /* 193 * Initial RAM Base Address Setup 194 */ 195 #define CONFIG_SYS_INIT_RAM_LOCK 1 196 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 197 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 198 #define CONFIG_SYS_GBL_DATA_OFFSET \ 199 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 200 201 /* 202 * Local Bus Configuration & Clock Setup 203 */ 204 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 205 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 206 #define CONFIG_SYS_LBC_LBCR 0x00040000 207 208 /* 209 * FLASH on the Local Bus 210 */ 211 #if 1 212 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 213 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 214 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 215 #define CONFIG_FLASH_CFI_LEGACY 216 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 217 #endif 218 219 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 220 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 221 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 222 223 /* Window base at flash base */ 224 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 225 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 226 227 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 228 | BR_PS_16 /* 16 bit port */ \ 229 | BR_MS_GPCM /* MSEL = GPCM */ \ 230 | BR_V) /* valid */ 231 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 232 | OR_UPM_XAM \ 233 | OR_GPCM_CSNT \ 234 | OR_GPCM_ACS_DIV2 \ 235 | OR_GPCM_XACS \ 236 | OR_GPCM_SCY_15 \ 237 | OR_GPCM_TRLX_SET \ 238 | OR_GPCM_EHTR_SET) 239 240 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 241 #define CONFIG_SYS_MAX_FLASH_SECT 135 242 243 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 244 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 245 246 /* 247 * FPGA 248 */ 249 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 250 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 251 252 /* Window base at FPGA base */ 253 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 254 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 255 256 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 257 | BR_PS_16 /* 16 bit port */ \ 258 | BR_MS_GPCM /* MSEL = GPCM */ \ 259 | BR_V) /* valid */ 260 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 261 | OR_UPM_XAM \ 262 | OR_GPCM_CSNT \ 263 | OR_GPCM_ACS_DIV2 \ 264 | OR_GPCM_XACS \ 265 | OR_GPCM_SCY_15 \ 266 | OR_GPCM_TRLX_SET \ 267 | OR_GPCM_EHTR_SET) 268 269 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 270 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 271 272 #define CONFIG_SYS_FPGA_COUNT 1 273 274 #define CONFIG_SYS_MCLINK_MAX 3 275 276 #define CONFIG_SYS_FPGA_PTR \ 277 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 278 279 /* 280 * Serial Port 281 */ 282 #define CONFIG_CONS_INDEX 2 283 #define CONFIG_SYS_NS16550_SERIAL 284 #define CONFIG_SYS_NS16550_REG_SIZE 1 285 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 286 287 #define CONFIG_SYS_BAUDRATE_TABLE \ 288 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 289 290 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 291 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 292 293 /* Pass open firmware flat tree */ 294 295 /* I2C */ 296 #define CONFIG_SYS_I2C 297 #define CONFIG_SYS_I2C_FSL 298 #define CONFIG_SYS_FSL_I2C_SPEED 400000 299 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 300 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 301 302 #define CONFIG_PCA953X /* NXP PCA9554 */ 303 #define CONFIG_PCA9698 /* NXP PCA9698 */ 304 305 #define CONFIG_SYS_I2C_IHS 306 #define CONFIG_SYS_I2C_IHS_CH0 307 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 308 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 309 #define CONFIG_SYS_I2C_IHS_CH1 310 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 311 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 312 #define CONFIG_SYS_I2C_IHS_CH2 313 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 314 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 315 #define CONFIG_SYS_I2C_IHS_CH3 316 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 317 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 318 319 #ifdef CONFIG_HRCON_DH 320 #define CONFIG_SYS_I2C_IHS_DUAL 321 #define CONFIG_SYS_I2C_IHS_CH0_1 322 #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 323 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F 324 #define CONFIG_SYS_I2C_IHS_CH1_1 325 #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 326 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F 327 #define CONFIG_SYS_I2C_IHS_CH2_1 328 #define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000 329 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F 330 #define CONFIG_SYS_I2C_IHS_CH3_1 331 #define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000 332 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F 333 #endif 334 335 /* 336 * Software (bit-bang) I2C driver configuration 337 */ 338 #define CONFIG_SYS_I2C_SOFT 339 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 340 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 341 #define I2C_SOFT_DECLARATIONS2 342 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 343 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 344 #define I2C_SOFT_DECLARATIONS3 345 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 346 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 347 #define I2C_SOFT_DECLARATIONS4 348 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 349 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 350 #define I2C_SOFT_DECLARATIONS5 351 #define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 352 #define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F 353 #define I2C_SOFT_DECLARATIONS6 354 #define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 355 #define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F 356 #define I2C_SOFT_DECLARATIONS7 357 #define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 358 #define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F 359 #define I2C_SOFT_DECLARATIONS8 360 #define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 361 #define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F 362 363 #ifdef CONFIG_HRCON_DH 364 #define I2C_SOFT_DECLARATIONS9 365 #define CONFIG_SYS_I2C_SOFT_SPEED_9 50000 366 #define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F 367 #define I2C_SOFT_DECLARATIONS10 368 #define CONFIG_SYS_I2C_SOFT_SPEED_10 50000 369 #define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F 370 #define I2C_SOFT_DECLARATIONS11 371 #define CONFIG_SYS_I2C_SOFT_SPEED_11 50000 372 #define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F 373 #define I2C_SOFT_DECLARATIONS12 374 #define CONFIG_SYS_I2C_SOFT_SPEED_12 50000 375 #define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F 376 #endif 377 378 #ifdef CONFIG_HRCON_DH 379 #define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20} 380 #define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8} 381 #define CONFIG_HRCON_FANS { {10, 0x4c}, {11, 0x4c}, \ 382 {12, 0x4c} } 383 #else 384 #define CONFIG_SYS_ICS8N3QV01_I2C {9, 10, 11, 12} 385 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 386 #define CONFIG_HRCON_FANS { {6, 0x4c}, {7, 0x4c}, \ 387 {8, 0x4c} } 388 #endif 389 390 #ifndef __ASSEMBLY__ 391 void fpga_gpio_set(unsigned int bus, int pin); 392 void fpga_gpio_clear(unsigned int bus, int pin); 393 int fpga_gpio_get(unsigned int bus, int pin); 394 void fpga_control_set(unsigned int bus, int pin); 395 void fpga_control_clear(unsigned int bus, int pin); 396 #endif 397 398 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200) 399 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100) 400 #define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4) 401 402 #ifdef CONFIG_HRCON_DH 403 #define I2C_ACTIVE \ 404 do { \ 405 if (I2C_ADAP_HWNR > 7) \ 406 fpga_control_set(I2C_FPGA_IDX, 0x0004); \ 407 else \ 408 fpga_control_clear(I2C_FPGA_IDX, 0x0004); \ 409 } while (0) 410 #else 411 #define I2C_ACTIVE { } 412 #endif 413 #define I2C_TRISTATE { } 414 #define I2C_READ \ 415 (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) 416 #define I2C_SDA(bit) \ 417 do { \ 418 if (bit) \ 419 fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 420 else \ 421 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 422 } while (0) 423 #define I2C_SCL(bit) \ 424 do { \ 425 if (bit) \ 426 fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 427 else \ 428 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 429 } while (0) 430 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 431 432 /* 433 * Software (bit-bang) MII driver configuration 434 */ 435 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 436 #define CONFIG_BITBANGMII_MULTI 437 438 /* 439 * OSD Setup 440 */ 441 #define CONFIG_SYS_OSD_SCREENS 1 442 #define CONFIG_SYS_DP501_DIFFERENTIAL 443 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 444 445 #ifdef CONFIG_HRCON_DH 446 #define CONFIG_SYS_OSD_DH 447 #endif 448 449 /* 450 * General PCI 451 * Addresses are mapped 1-1. 452 */ 453 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 454 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 455 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 456 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 457 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 458 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 459 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 460 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 461 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 462 463 /* enable PCIE clock */ 464 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 465 466 #define CONFIG_PCI_INDIRECT_BRIDGE 467 #define CONFIG_PCIE 468 469 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 470 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 471 472 /* 473 * TSEC 474 */ 475 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 476 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 477 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 478 479 /* 480 * TSEC ethernet configuration 481 */ 482 #define CONFIG_MII 1 /* MII PHY management */ 483 #define CONFIG_TSEC1 484 #define CONFIG_TSEC1_NAME "eTSEC0" 485 #define TSEC1_PHY_ADDR 1 486 #define TSEC1_PHYIDX 0 487 #define TSEC1_FLAGS TSEC_GIGABIT 488 489 /* Options are: eTSEC[0-1] */ 490 #define CONFIG_ETHPRIME "eTSEC0" 491 492 /* 493 * Environment 494 */ 495 #if 1 496 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 497 CONFIG_SYS_MONITOR_LEN) 498 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 499 #define CONFIG_ENV_SIZE 0x2000 500 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 501 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 502 #else 503 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 504 #endif 505 506 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 507 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 508 509 /* 510 * Command line configuration. 511 */ 512 #define CONFIG_CMD_PCI 513 514 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 515 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 516 517 /* 518 * Miscellaneous configurable options 519 */ 520 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 521 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 522 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 523 524 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 525 526 /* Print Buffer Size */ 527 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 528 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 529 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 530 531 /* 532 * For booting Linux, the board info and command line data 533 * have to be in the first 256 MB of memory, since this is 534 * the maximum mapped by the Linux kernel during initialization. 535 */ 536 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 537 538 /* 539 * Core HID Setup 540 */ 541 #define CONFIG_SYS_HID0_INIT 0x000000000 542 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 543 HID0_ENABLE_INSTRUCTION_CACHE | \ 544 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 545 #define CONFIG_SYS_HID2 HID2_HBE 546 547 /* 548 * MMU Setup 549 */ 550 551 /* DDR: cache cacheable */ 552 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 553 BATL_MEMCOHERENCE) 554 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 555 BATU_VS | BATU_VP) 556 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 557 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 558 559 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 560 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 561 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 562 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 563 BATU_VP) 564 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 565 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 566 567 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 568 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 569 BATL_MEMCOHERENCE) 570 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 571 BATU_VS | BATU_VP) 572 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 573 BATL_CACHEINHIBIT | \ 574 BATL_GUARDEDSTORAGE) 575 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 576 577 /* Stack in dcache: cacheable, no memory coherence */ 578 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 579 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 580 BATU_VS | BATU_VP) 581 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 582 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 583 584 /* 585 * Environment Configuration 586 */ 587 588 #define CONFIG_ENV_OVERWRITE 589 590 #if defined(CONFIG_TSEC_ENET) 591 #define CONFIG_HAS_ETH0 592 #endif 593 594 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 595 596 597 #define CONFIG_HOSTNAME hrcon 598 #define CONFIG_ROOTPATH "/opt/nfsroot" 599 #define CONFIG_BOOTFILE "uImage" 600 601 #define CONFIG_PREBOOT /* enable preboot variable */ 602 603 #define CONFIG_EXTRA_ENV_SETTINGS \ 604 "netdev=eth0\0" \ 605 "consoledev=ttyS1\0" \ 606 "u-boot=u-boot.bin\0" \ 607 "kernel_addr=1000000\0" \ 608 "fdt_addr=C00000\0" \ 609 "fdtfile=hrcon.dtb\0" \ 610 "load=tftp ${loadaddr} ${u-boot}\0" \ 611 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 612 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 613 " +${filesize};cp.b ${fileaddr} " \ 614 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 615 "upd=run load update\0" \ 616 617 #define CONFIG_NFSBOOTCOMMAND \ 618 "setenv bootargs root=/dev/nfs rw " \ 619 "nfsroot=$serverip:$rootpath " \ 620 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 621 "console=$consoledev,$baudrate $othbootargs;" \ 622 "tftp ${kernel_addr} $bootfile;" \ 623 "tftp ${fdt_addr} $fdtfile;" \ 624 "bootm ${kernel_addr} - ${fdt_addr}" 625 626 #define CONFIG_MMCBOOTCOMMAND \ 627 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 628 "console=$consoledev,$baudrate $othbootargs;" \ 629 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 630 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 631 "bootm ${kernel_addr} - ${fdt_addr}" 632 633 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 634 635 #endif /* __CONFIG_H */ 636