1 /* 2 * (C) Copyright 2014 3 * Dirk Eibach, Guntermann & Drunck GmbH, dirk.eibach@gdsys.cc 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_HRCON 1 /* HRCON board specific */ 20 21 #define CONFIG_BOARD_EARLY_INIT_R 22 #define CONFIG_LAST_STAGE_INIT 23 24 #define CONFIG_FSL_ESDHC 25 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 26 27 /* 28 * System Clock Setup 29 */ 30 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 31 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 32 33 /* 34 * Hardware Reset Configuration Word 35 * if CLKIN is 66.66MHz, then 36 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 37 * We choose the A type silicon as default, so the core is 400Mhz. 38 */ 39 #define CONFIG_SYS_HRCW_LOW (\ 40 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 41 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 42 HRCWL_SVCOD_DIV_2 |\ 43 HRCWL_CSB_TO_CLKIN_4X1 |\ 44 HRCWL_CORE_TO_CSB_3X1) 45 /* 46 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 47 * in 8308's HRCWH according to the manual, but original Freescale's 48 * code has them and I've expirienced some problems using the board 49 * with BDI3000 attached when I've tried to set these bits to zero 50 * (UART doesn't work after the 'reset run' command). 51 */ 52 #define CONFIG_SYS_HRCW_HIGH (\ 53 HRCWH_PCI_HOST |\ 54 HRCWH_PCI1_ARBITER_ENABLE |\ 55 HRCWH_CORE_ENABLE |\ 56 HRCWH_FROM_0XFFF00100 |\ 57 HRCWH_BOOTSEQ_DISABLE |\ 58 HRCWH_SW_WATCHDOG_DISABLE |\ 59 HRCWH_ROM_LOC_LOCAL_16BIT |\ 60 HRCWH_RL_EXT_LEGACY |\ 61 HRCWH_TSEC1M_IN_RGMII |\ 62 HRCWH_TSEC2M_IN_RGMII |\ 63 HRCWH_BIG_ENDIAN) 64 65 /* 66 * System IO Config 67 */ 68 #define CONFIG_SYS_SICRH (\ 69 SICRH_ESDHC_A_SD |\ 70 SICRH_ESDHC_B_SD |\ 71 SICRH_ESDHC_C_SD |\ 72 SICRH_GPIO_A_GPIO |\ 73 SICRH_GPIO_B_GPIO |\ 74 SICRH_IEEE1588_A_GPIO |\ 75 SICRH_USB |\ 76 SICRH_GTM_GPIO |\ 77 SICRH_IEEE1588_B_GPIO |\ 78 SICRH_ETSEC2_GPIO |\ 79 SICRH_GPIOSEL_1 |\ 80 SICRH_TMROBI_V3P3 |\ 81 SICRH_TSOBI1_V2P5 |\ 82 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 83 #define CONFIG_SYS_SICRL (\ 84 SICRL_SPI_PF0 |\ 85 SICRL_UART_PF0 |\ 86 SICRL_IRQ_PF0 |\ 87 SICRL_I2C2_PF0 |\ 88 SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ 89 90 /* 91 * IMMR new address 92 */ 93 #define CONFIG_SYS_IMMR 0xE0000000 94 95 /* 96 * SERDES 97 */ 98 #define CONFIG_FSL_SERDES 99 #define CONFIG_FSL_SERDES1 0xe3000 100 101 /* 102 * Arbiter Setup 103 */ 104 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 105 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 106 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 107 108 /* 109 * DDR Setup 110 */ 111 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 112 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 113 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 114 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 115 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 116 | DDRCDR_PZ_LOZ \ 117 | DDRCDR_NZ_LOZ \ 118 | DDRCDR_ODT \ 119 | DDRCDR_Q_DRN) 120 /* 0x7b880001 */ 121 /* 122 * Manually set up DDR parameters 123 * consist of one chip NT5TU64M16HG from NANYA 124 */ 125 126 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 127 128 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 129 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 130 | CSCONFIG_ODT_RD_NEVER \ 131 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 132 | CSCONFIG_BANK_BIT_3 \ 133 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 134 /* 0x80010102 */ 135 #define CONFIG_SYS_DDR_TIMING_3 0 136 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 137 | (0 << TIMING_CFG0_WRT_SHIFT) \ 138 | (0 << TIMING_CFG0_RRT_SHIFT) \ 139 | (0 << TIMING_CFG0_WWT_SHIFT) \ 140 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 141 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 142 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 143 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 144 /* 0x00260802 */ 145 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 146 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 147 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 148 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 149 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 150 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 151 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 152 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 153 /* 0x26279222 */ 154 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 155 | (4 << TIMING_CFG2_CPO_SHIFT) \ 156 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 157 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 158 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 159 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 160 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 161 /* 0x021848c5 */ 162 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 163 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 164 /* 0x08240100 */ 165 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 166 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 167 | SDRAM_CFG_DBW_16) 168 /* 0x43100000 */ 169 170 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 171 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 172 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 173 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 174 #define CONFIG_SYS_DDR_MODE2 0x00000000 175 176 /* 177 * Memory test 178 */ 179 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 180 #define CONFIG_SYS_MEMTEST_END 0x07f00000 181 182 /* 183 * The reserved memory 184 */ 185 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 186 187 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 188 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 189 190 /* 191 * Initial RAM Base Address Setup 192 */ 193 #define CONFIG_SYS_INIT_RAM_LOCK 1 194 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 195 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 196 #define CONFIG_SYS_GBL_DATA_OFFSET \ 197 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 198 199 /* 200 * Local Bus Configuration & Clock Setup 201 */ 202 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 203 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 204 #define CONFIG_SYS_LBC_LBCR 0x00040000 205 206 /* 207 * FLASH on the Local Bus 208 */ 209 #if 1 210 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 211 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 212 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 213 #define CONFIG_FLASH_CFI_LEGACY 214 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 215 #endif 216 217 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 218 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 219 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 220 221 /* Window base at flash base */ 222 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 223 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 224 225 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 226 | BR_PS_16 /* 16 bit port */ \ 227 | BR_MS_GPCM /* MSEL = GPCM */ \ 228 | BR_V) /* valid */ 229 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 230 | OR_UPM_XAM \ 231 | OR_GPCM_CSNT \ 232 | OR_GPCM_ACS_DIV2 \ 233 | OR_GPCM_XACS \ 234 | OR_GPCM_SCY_15 \ 235 | OR_GPCM_TRLX_SET \ 236 | OR_GPCM_EHTR_SET) 237 238 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 239 #define CONFIG_SYS_MAX_FLASH_SECT 135 240 241 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 242 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 243 244 /* 245 * FPGA 246 */ 247 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 248 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 249 250 /* Window base at FPGA base */ 251 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 252 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 253 254 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 255 | BR_PS_16 /* 16 bit port */ \ 256 | BR_MS_GPCM /* MSEL = GPCM */ \ 257 | BR_V) /* valid */ 258 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 259 | OR_UPM_XAM \ 260 | OR_GPCM_CSNT \ 261 | OR_GPCM_ACS_DIV2 \ 262 | OR_GPCM_XACS \ 263 | OR_GPCM_SCY_15 \ 264 | OR_GPCM_TRLX_SET \ 265 | OR_GPCM_EHTR_SET) 266 267 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 268 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 269 270 #define CONFIG_SYS_FPGA_COUNT 1 271 272 #define CONFIG_SYS_MCLINK_MAX 3 273 274 #define CONFIG_SYS_FPGA_PTR \ 275 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 276 277 /* 278 * Serial Port 279 */ 280 #define CONFIG_CONS_INDEX 2 281 #define CONFIG_SYS_NS16550_SERIAL 282 #define CONFIG_SYS_NS16550_REG_SIZE 1 283 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 284 285 #define CONFIG_SYS_BAUDRATE_TABLE \ 286 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 287 288 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 289 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 290 291 /* Pass open firmware flat tree */ 292 293 /* I2C */ 294 #define CONFIG_SYS_I2C 295 #define CONFIG_SYS_I2C_FSL 296 #define CONFIG_SYS_FSL_I2C_SPEED 400000 297 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 298 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 299 300 #define CONFIG_PCA953X /* NXP PCA9554 */ 301 #define CONFIG_PCA9698 /* NXP PCA9698 */ 302 303 #define CONFIG_SYS_I2C_IHS 304 #define CONFIG_SYS_I2C_IHS_CH0 305 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 306 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 307 #define CONFIG_SYS_I2C_IHS_CH1 308 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 309 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 310 #define CONFIG_SYS_I2C_IHS_CH2 311 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 312 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 313 #define CONFIG_SYS_I2C_IHS_CH3 314 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 315 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 316 317 #ifdef CONFIG_HRCON_DH 318 #define CONFIG_SYS_I2C_IHS_DUAL 319 #define CONFIG_SYS_I2C_IHS_CH0_1 320 #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 321 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F 322 #define CONFIG_SYS_I2C_IHS_CH1_1 323 #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 324 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F 325 #define CONFIG_SYS_I2C_IHS_CH2_1 326 #define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000 327 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F 328 #define CONFIG_SYS_I2C_IHS_CH3_1 329 #define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000 330 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F 331 #endif 332 333 /* 334 * Software (bit-bang) I2C driver configuration 335 */ 336 #define CONFIG_SYS_I2C_SOFT 337 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 338 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 339 #define I2C_SOFT_DECLARATIONS2 340 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 341 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 342 #define I2C_SOFT_DECLARATIONS3 343 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 344 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 345 #define I2C_SOFT_DECLARATIONS4 346 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 347 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 348 #define I2C_SOFT_DECLARATIONS5 349 #define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 350 #define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F 351 #define I2C_SOFT_DECLARATIONS6 352 #define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 353 #define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F 354 #define I2C_SOFT_DECLARATIONS7 355 #define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 356 #define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F 357 #define I2C_SOFT_DECLARATIONS8 358 #define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 359 #define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F 360 361 #ifdef CONFIG_HRCON_DH 362 #define I2C_SOFT_DECLARATIONS9 363 #define CONFIG_SYS_I2C_SOFT_SPEED_9 50000 364 #define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F 365 #define I2C_SOFT_DECLARATIONS10 366 #define CONFIG_SYS_I2C_SOFT_SPEED_10 50000 367 #define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F 368 #define I2C_SOFT_DECLARATIONS11 369 #define CONFIG_SYS_I2C_SOFT_SPEED_11 50000 370 #define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F 371 #define I2C_SOFT_DECLARATIONS12 372 #define CONFIG_SYS_I2C_SOFT_SPEED_12 50000 373 #define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F 374 #endif 375 376 #ifdef CONFIG_HRCON_DH 377 #define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20} 378 #define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8} 379 #define CONFIG_HRCON_FANS { {10, 0x4c}, {11, 0x4c}, \ 380 {12, 0x4c} } 381 #else 382 #define CONFIG_SYS_ICS8N3QV01_I2C {9, 10, 11, 12} 383 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 384 #define CONFIG_HRCON_FANS { {6, 0x4c}, {7, 0x4c}, \ 385 {8, 0x4c} } 386 #endif 387 388 #ifndef __ASSEMBLY__ 389 void fpga_gpio_set(unsigned int bus, int pin); 390 void fpga_gpio_clear(unsigned int bus, int pin); 391 int fpga_gpio_get(unsigned int bus, int pin); 392 void fpga_control_set(unsigned int bus, int pin); 393 void fpga_control_clear(unsigned int bus, int pin); 394 #endif 395 396 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200) 397 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100) 398 #define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4) 399 400 #ifdef CONFIG_HRCON_DH 401 #define I2C_ACTIVE \ 402 do { \ 403 if (I2C_ADAP_HWNR > 7) \ 404 fpga_control_set(I2C_FPGA_IDX, 0x0004); \ 405 else \ 406 fpga_control_clear(I2C_FPGA_IDX, 0x0004); \ 407 } while (0) 408 #else 409 #define I2C_ACTIVE { } 410 #endif 411 #define I2C_TRISTATE { } 412 #define I2C_READ \ 413 (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) 414 #define I2C_SDA(bit) \ 415 do { \ 416 if (bit) \ 417 fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 418 else \ 419 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 420 } while (0) 421 #define I2C_SCL(bit) \ 422 do { \ 423 if (bit) \ 424 fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 425 else \ 426 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 427 } while (0) 428 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 429 430 /* 431 * Software (bit-bang) MII driver configuration 432 */ 433 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 434 #define CONFIG_BITBANGMII_MULTI 435 436 /* 437 * OSD Setup 438 */ 439 #define CONFIG_SYS_OSD_SCREENS 1 440 #define CONFIG_SYS_DP501_DIFFERENTIAL 441 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 442 443 #ifdef CONFIG_HRCON_DH 444 #define CONFIG_SYS_OSD_DH 445 #endif 446 447 /* 448 * General PCI 449 * Addresses are mapped 1-1. 450 */ 451 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 452 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 453 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 454 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 455 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 456 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 457 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 458 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 459 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 460 461 /* enable PCIE clock */ 462 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 463 464 #define CONFIG_PCI_INDIRECT_BRIDGE 465 #define CONFIG_PCIE 466 467 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 468 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 469 470 /* 471 * TSEC 472 */ 473 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 474 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 475 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 476 477 /* 478 * TSEC ethernet configuration 479 */ 480 #define CONFIG_MII 1 /* MII PHY management */ 481 #define CONFIG_TSEC1 482 #define CONFIG_TSEC1_NAME "eTSEC0" 483 #define TSEC1_PHY_ADDR 1 484 #define TSEC1_PHYIDX 0 485 #define TSEC1_FLAGS TSEC_GIGABIT 486 487 /* Options are: eTSEC[0-1] */ 488 #define CONFIG_ETHPRIME "eTSEC0" 489 490 /* 491 * Environment 492 */ 493 #if 1 494 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 495 CONFIG_SYS_MONITOR_LEN) 496 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 497 #define CONFIG_ENV_SIZE 0x2000 498 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 499 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 500 #else 501 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 502 #endif 503 504 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 505 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 506 507 /* 508 * Command line configuration. 509 */ 510 511 /* 512 * Miscellaneous configurable options 513 */ 514 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 515 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 516 517 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 518 519 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 520 521 /* 522 * For booting Linux, the board info and command line data 523 * have to be in the first 256 MB of memory, since this is 524 * the maximum mapped by the Linux kernel during initialization. 525 */ 526 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 527 528 /* 529 * Core HID Setup 530 */ 531 #define CONFIG_SYS_HID0_INIT 0x000000000 532 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 533 HID0_ENABLE_INSTRUCTION_CACHE | \ 534 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 535 #define CONFIG_SYS_HID2 HID2_HBE 536 537 /* 538 * MMU Setup 539 */ 540 541 /* DDR: cache cacheable */ 542 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 543 BATL_MEMCOHERENCE) 544 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 545 BATU_VS | BATU_VP) 546 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 547 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 548 549 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 550 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 551 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 552 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 553 BATU_VP) 554 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 555 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 556 557 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 558 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 559 BATL_MEMCOHERENCE) 560 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 561 BATU_VS | BATU_VP) 562 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 563 BATL_CACHEINHIBIT | \ 564 BATL_GUARDEDSTORAGE) 565 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 566 567 /* Stack in dcache: cacheable, no memory coherence */ 568 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 569 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 570 BATU_VS | BATU_VP) 571 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 572 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 573 574 /* 575 * Environment Configuration 576 */ 577 578 #define CONFIG_ENV_OVERWRITE 579 580 #if defined(CONFIG_TSEC_ENET) 581 #define CONFIG_HAS_ETH0 582 #endif 583 584 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 585 586 587 #define CONFIG_HOSTNAME hrcon 588 #define CONFIG_ROOTPATH "/opt/nfsroot" 589 #define CONFIG_BOOTFILE "uImage" 590 591 #define CONFIG_PREBOOT /* enable preboot variable */ 592 593 #define CONFIG_EXTRA_ENV_SETTINGS \ 594 "netdev=eth0\0" \ 595 "consoledev=ttyS1\0" \ 596 "u-boot=u-boot.bin\0" \ 597 "kernel_addr=1000000\0" \ 598 "fdt_addr=C00000\0" \ 599 "fdtfile=hrcon.dtb\0" \ 600 "load=tftp ${loadaddr} ${u-boot}\0" \ 601 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 602 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 603 " +${filesize};cp.b ${fileaddr} " \ 604 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 605 "upd=run load update\0" \ 606 607 #define CONFIG_NFSBOOTCOMMAND \ 608 "setenv bootargs root=/dev/nfs rw " \ 609 "nfsroot=$serverip:$rootpath " \ 610 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 611 "console=$consoledev,$baudrate $othbootargs;" \ 612 "tftp ${kernel_addr} $bootfile;" \ 613 "tftp ${fdt_addr} $fdtfile;" \ 614 "bootm ${kernel_addr} - ${fdt_addr}" 615 616 #define CONFIG_MMCBOOTCOMMAND \ 617 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 618 "console=$consoledev,$baudrate $othbootargs;" \ 619 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 620 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 621 "bootm ${kernel_addr} - ${fdt_addr}" 622 623 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 624 625 #endif /* __CONFIG_H */ 626