1 /* 2 * (C) Copyright 2014 3 * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_HRCON 1 /* HRCON board specific */ 20 21 #define CONFIG_SYS_TEXT_BASE 0xFE000000 22 23 #define CONFIG_IDENT_STRING " hrcon 0.01" 24 25 #define CONFIG_SYS_GENERIC_BOARD 26 27 #define CONFIG_BOARD_EARLY_INIT_F 28 #define CONFIG_BOARD_EARLY_INIT_R 29 #define CONFIG_LAST_STAGE_INIT 30 31 /* new uImage format support */ 32 #define CONFIG_FIT 1 33 #define CONFIG_FIT_VERBOSE 1 34 35 #define CONFIG_MMC 36 #define CONFIG_FSL_ESDHC 37 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 38 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 39 40 #define CONFIG_CMD_MMC 41 #define CONFIG_GENERIC_MMC 42 #define CONFIG_DOS_PARTITION 43 #define CONFIG_CMD_EXT2 44 45 #define CONFIG_CMD_FPGAD 46 #define CONFIG_CMD_IOLOOP 47 48 /* 49 * System Clock Setup 50 */ 51 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 52 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 53 54 /* 55 * Hardware Reset Configuration Word 56 * if CLKIN is 66.66MHz, then 57 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 58 * We choose the A type silicon as default, so the core is 400Mhz. 59 */ 60 #define CONFIG_SYS_HRCW_LOW (\ 61 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 62 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 63 HRCWL_SVCOD_DIV_2 |\ 64 HRCWL_CSB_TO_CLKIN_4X1 |\ 65 HRCWL_CORE_TO_CSB_3X1) 66 /* 67 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 68 * in 8308's HRCWH according to the manual, but original Freescale's 69 * code has them and I've expirienced some problems using the board 70 * with BDI3000 attached when I've tried to set these bits to zero 71 * (UART doesn't work after the 'reset run' command). 72 */ 73 #define CONFIG_SYS_HRCW_HIGH (\ 74 HRCWH_PCI_HOST |\ 75 HRCWH_PCI1_ARBITER_ENABLE |\ 76 HRCWH_CORE_ENABLE |\ 77 HRCWH_FROM_0XFFF00100 |\ 78 HRCWH_BOOTSEQ_DISABLE |\ 79 HRCWH_SW_WATCHDOG_DISABLE |\ 80 HRCWH_ROM_LOC_LOCAL_16BIT |\ 81 HRCWH_RL_EXT_LEGACY |\ 82 HRCWH_TSEC1M_IN_RGMII |\ 83 HRCWH_TSEC2M_IN_RGMII |\ 84 HRCWH_BIG_ENDIAN) 85 86 /* 87 * System IO Config 88 */ 89 #define CONFIG_SYS_SICRH (\ 90 SICRH_ESDHC_A_SD |\ 91 SICRH_ESDHC_B_SD |\ 92 SICRH_ESDHC_C_SD |\ 93 SICRH_GPIO_A_GPIO |\ 94 SICRH_GPIO_B_GPIO |\ 95 SICRH_IEEE1588_A_GPIO |\ 96 SICRH_USB |\ 97 SICRH_GTM_GPIO |\ 98 SICRH_IEEE1588_B_GPIO |\ 99 SICRH_ETSEC2_GPIO |\ 100 SICRH_GPIOSEL_1 |\ 101 SICRH_TMROBI_V3P3 |\ 102 SICRH_TSOBI1_V2P5 |\ 103 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 104 #define CONFIG_SYS_SICRL (\ 105 SICRL_SPI_PF0 |\ 106 SICRL_UART_PF0 |\ 107 SICRL_IRQ_PF0 |\ 108 SICRL_I2C2_PF0 |\ 109 SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ 110 111 /* 112 * IMMR new address 113 */ 114 #define CONFIG_SYS_IMMR 0xE0000000 115 116 /* 117 * SERDES 118 */ 119 #define CONFIG_FSL_SERDES 120 #define CONFIG_FSL_SERDES1 0xe3000 121 122 /* 123 * Arbiter Setup 124 */ 125 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 126 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 127 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 128 129 /* 130 * DDR Setup 131 */ 132 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 133 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 134 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 135 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 136 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 137 | DDRCDR_PZ_LOZ \ 138 | DDRCDR_NZ_LOZ \ 139 | DDRCDR_ODT \ 140 | DDRCDR_Q_DRN) 141 /* 0x7b880001 */ 142 /* 143 * Manually set up DDR parameters 144 * consist of one chip NT5TU64M16HG from NANYA 145 */ 146 147 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 148 149 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 150 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 151 | CSCONFIG_ODT_RD_NEVER \ 152 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 153 | CSCONFIG_BANK_BIT_3 \ 154 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 155 /* 0x80010102 */ 156 #define CONFIG_SYS_DDR_TIMING_3 0 157 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 158 | (0 << TIMING_CFG0_WRT_SHIFT) \ 159 | (0 << TIMING_CFG0_RRT_SHIFT) \ 160 | (0 << TIMING_CFG0_WWT_SHIFT) \ 161 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 162 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 163 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 164 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 165 /* 0x00260802 */ 166 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 167 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 168 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 169 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 170 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 171 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 172 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 173 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 174 /* 0x26279222 */ 175 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 176 | (4 << TIMING_CFG2_CPO_SHIFT) \ 177 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 178 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 179 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 180 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 181 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 182 /* 0x021848c5 */ 183 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 184 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 185 /* 0x08240100 */ 186 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 187 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 188 | SDRAM_CFG_DBW_16) 189 /* 0x43100000 */ 190 191 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 192 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 193 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 194 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 195 #define CONFIG_SYS_DDR_MODE2 0x00000000 196 197 /* 198 * Memory test 199 */ 200 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 201 #define CONFIG_SYS_MEMTEST_END 0x07f00000 202 203 /* 204 * The reserved memory 205 */ 206 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 207 208 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 209 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 210 211 /* 212 * Initial RAM Base Address Setup 213 */ 214 #define CONFIG_SYS_INIT_RAM_LOCK 1 215 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 216 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 217 #define CONFIG_SYS_GBL_DATA_OFFSET \ 218 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 219 220 /* 221 * Local Bus Configuration & Clock Setup 222 */ 223 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 224 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 225 #define CONFIG_SYS_LBC_LBCR 0x00040000 226 227 /* 228 * FLASH on the Local Bus 229 */ 230 #if 1 231 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 232 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 233 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 234 #define CONFIG_FLASH_CFI_LEGACY 235 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 236 #else 237 #define CONFIG_SYS_NO_FLASH 238 #endif 239 240 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 241 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 242 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 243 244 /* Window base at flash base */ 245 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 246 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 247 248 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 249 | BR_PS_16 /* 16 bit port */ \ 250 | BR_MS_GPCM /* MSEL = GPCM */ \ 251 | BR_V) /* valid */ 252 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 253 | OR_UPM_XAM \ 254 | OR_GPCM_CSNT \ 255 | OR_GPCM_ACS_DIV2 \ 256 | OR_GPCM_XACS \ 257 | OR_GPCM_SCY_15 \ 258 | OR_GPCM_TRLX_SET \ 259 | OR_GPCM_EHTR_SET) 260 261 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 262 #define CONFIG_SYS_MAX_FLASH_SECT 135 263 264 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 265 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 266 267 /* 268 * FPGA 269 */ 270 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 271 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 272 273 /* Window base at FPGA base */ 274 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 275 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 276 277 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 278 | BR_PS_16 /* 16 bit port */ \ 279 | BR_MS_GPCM /* MSEL = GPCM */ \ 280 | BR_V) /* valid */ 281 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 282 | OR_UPM_XAM \ 283 | OR_GPCM_CSNT \ 284 | OR_GPCM_ACS_DIV2 \ 285 | OR_GPCM_XACS \ 286 | OR_GPCM_SCY_15 \ 287 | OR_GPCM_TRLX_SET \ 288 | OR_GPCM_EHTR_SET) 289 290 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 291 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 292 293 #define CONFIG_SYS_FPGA_COUNT 1 294 295 #define CONFIG_SYS_MCLINK_MAX 3 296 297 #define CONFIG_SYS_FPGA_PTR \ 298 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 299 300 /* 301 * Serial Port 302 */ 303 #define CONFIG_CONS_INDEX 2 304 #define CONFIG_SYS_NS16550 305 #define CONFIG_SYS_NS16550_SERIAL 306 #define CONFIG_SYS_NS16550_REG_SIZE 1 307 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 308 309 #define CONFIG_SYS_BAUDRATE_TABLE \ 310 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 311 312 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 313 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 314 315 /* Use the HUSH parser */ 316 #define CONFIG_SYS_HUSH_PARSER 317 318 /* Pass open firmware flat tree */ 319 #define CONFIG_OF_LIBFDT 1 320 #define CONFIG_OF_BOARD_SETUP 1 321 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 322 323 /* I2C */ 324 #define CONFIG_SYS_I2C 325 #define CONFIG_SYS_I2C_FSL 326 #define CONFIG_SYS_FSL_I2C_SPEED 400000 327 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 328 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 329 330 #define CONFIG_PCA953X /* NXP PCA9554 */ 331 #define CONFIG_PCA9698 /* NXP PCA9698 */ 332 333 #define CONFIG_SYS_I2C_IHS 334 #define CONFIG_SYS_I2C_IHS_CH0 335 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 336 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 337 #define CONFIG_SYS_I2C_IHS_CH1 338 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 339 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 340 #define CONFIG_SYS_I2C_IHS_CH2 341 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 342 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 343 #define CONFIG_SYS_I2C_IHS_CH3 344 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 345 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 346 347 /* 348 * Software (bit-bang) I2C driver configuration 349 */ 350 #define CONFIG_SYS_I2C_SOFT 351 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 352 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 353 #define I2C_SOFT_DECLARATIONS2 354 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 355 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 356 #define I2C_SOFT_DECLARATIONS3 357 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 358 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 359 #define I2C_SOFT_DECLARATIONS4 360 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 361 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 362 363 #define CONFIG_SYS_ICS8N3QV01_I2C {5, 6, 7, 8} 364 #define CONFIG_SYS_CH7301_I2C {5, 6, 7, 8} 365 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 366 367 #ifndef __ASSEMBLY__ 368 void fpga_gpio_set(unsigned int bus, int pin); 369 void fpga_gpio_clear(unsigned int bus, int pin); 370 int fpga_gpio_get(unsigned int bus, int pin); 371 #endif 372 373 #define I2C_ACTIVE { } 374 #define I2C_TRISTATE { } 375 #define I2C_READ \ 376 (fpga_gpio_get(I2C_ADAP_HWNR, 0x0040) ? 1 : 0) 377 #define I2C_SDA(bit) \ 378 do { \ 379 if (bit) \ 380 fpga_gpio_set(I2C_ADAP_HWNR, 0x0040); \ 381 else \ 382 fpga_gpio_clear(I2C_ADAP_HWNR, 0x0040); \ 383 } while (0) 384 #define I2C_SCL(bit) \ 385 do { \ 386 if (bit) \ 387 fpga_gpio_set(I2C_ADAP_HWNR, 0x0020); \ 388 else \ 389 fpga_gpio_clear(I2C_ADAP_HWNR, 0x0020); \ 390 } while (0) 391 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 392 393 /* 394 * Software (bit-bang) MII driver configuration 395 */ 396 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 397 #define CONFIG_BITBANGMII_MULTI 398 399 /* 400 * OSD Setup 401 */ 402 #define CONFIG_SYS_OSD_SCREENS 1 403 #define CONFIG_SYS_DP501_DIFFERENTIAL 404 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 405 406 /* 407 * General PCI 408 * Addresses are mapped 1-1. 409 */ 410 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 411 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 412 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 413 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 414 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 415 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 416 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 417 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 418 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 419 420 /* enable PCIE clock */ 421 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 422 423 #define CONFIG_PCI 424 #define CONFIG_PCI_INDIRECT_BRIDGE 425 #define CONFIG_PCIE 426 427 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 428 429 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 430 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 431 432 /* 433 * TSEC 434 */ 435 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 436 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 437 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 438 439 /* 440 * TSEC ethernet configuration 441 */ 442 #define CONFIG_MII 1 /* MII PHY management */ 443 #define CONFIG_TSEC1 444 #define CONFIG_TSEC1_NAME "eTSEC0" 445 #define TSEC1_PHY_ADDR 1 446 #define TSEC1_PHYIDX 0 447 #define TSEC1_FLAGS TSEC_GIGABIT 448 449 /* Options are: eTSEC[0-1] */ 450 #define CONFIG_ETHPRIME "eTSEC0" 451 452 /* 453 * Environment 454 */ 455 #if 1 456 #define CONFIG_ENV_IS_IN_FLASH 1 457 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 458 CONFIG_SYS_MONITOR_LEN) 459 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 460 #define CONFIG_ENV_SIZE 0x2000 461 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 462 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 463 #else 464 #define CONFIG_ENV_IS_NOWHERE 465 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 466 #endif 467 468 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 469 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 470 471 /* 472 * Command line configuration. 473 */ 474 #define CONFIG_CMD_I2C 475 #define CONFIG_CMD_MII 476 #define CONFIG_CMD_PCI 477 #define CONFIG_CMD_PING 478 479 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 480 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 481 482 /* 483 * Miscellaneous configurable options 484 */ 485 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 486 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 487 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 488 489 #undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ 490 491 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 492 493 #define CONFIG_SYS_CONSOLE_INFO_QUIET 494 495 /* Print Buffer Size */ 496 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 497 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 498 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 499 500 /* 501 * For booting Linux, the board info and command line data 502 * have to be in the first 256 MB of memory, since this is 503 * the maximum mapped by the Linux kernel during initialization. 504 */ 505 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 506 507 /* 508 * Core HID Setup 509 */ 510 #define CONFIG_SYS_HID0_INIT 0x000000000 511 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 512 HID0_ENABLE_INSTRUCTION_CACHE | \ 513 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 514 #define CONFIG_SYS_HID2 HID2_HBE 515 516 /* 517 * MMU Setup 518 */ 519 520 /* DDR: cache cacheable */ 521 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 522 BATL_MEMCOHERENCE) 523 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 524 BATU_VS | BATU_VP) 525 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 526 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 527 528 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 529 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 530 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 531 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 532 BATU_VP) 533 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 534 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 535 536 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 537 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 538 BATL_MEMCOHERENCE) 539 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 540 BATU_VS | BATU_VP) 541 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 542 BATL_CACHEINHIBIT | \ 543 BATL_GUARDEDSTORAGE) 544 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 545 546 /* Stack in dcache: cacheable, no memory coherence */ 547 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 548 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 549 BATU_VS | BATU_VP) 550 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 551 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 552 553 /* 554 * Environment Configuration 555 */ 556 557 #define CONFIG_ENV_OVERWRITE 558 559 #if defined(CONFIG_TSEC_ENET) 560 #define CONFIG_HAS_ETH0 561 #endif 562 563 #define CONFIG_BAUDRATE 115200 564 565 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 566 567 #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ 568 569 #define CONFIG_HOSTNAME hrcon 570 #define CONFIG_ROOTPATH "/opt/nfsroot" 571 #define CONFIG_BOOTFILE "uImage" 572 573 #define CONFIG_PREBOOT /* enable preboot variable */ 574 575 #define CONFIG_EXTRA_ENV_SETTINGS \ 576 "netdev=eth0\0" \ 577 "consoledev=ttyS1\0" \ 578 "u-boot=u-boot.bin\0" \ 579 "kernel_addr=1000000\0" \ 580 "fdt_addr=C00000\0" \ 581 "fdtfile=hrcon.dtb\0" \ 582 "load=tftp ${loadaddr} ${u-boot}\0" \ 583 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 584 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 585 " +${filesize};cp.b ${fileaddr} " \ 586 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 587 "upd=run load update\0" \ 588 589 #define CONFIG_NFSBOOTCOMMAND \ 590 "setenv bootargs root=/dev/nfs rw " \ 591 "nfsroot=$serverip:$rootpath " \ 592 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 593 "console=$consoledev,$baudrate $othbootargs;" \ 594 "tftp ${kernel_addr} $bootfile;" \ 595 "tftp ${fdt_addr} $fdtfile;" \ 596 "bootm ${kernel_addr} - ${fdt_addr}" 597 598 #define CONFIG_MMCBOOTCOMMAND \ 599 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 600 "console=$consoledev,$baudrate $othbootargs;" \ 601 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 602 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 603 "bootm ${kernel_addr} - ${fdt_addr}" 604 605 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 606 607 608 #endif /* __CONFIG_H */ 609