1 /* 2 * (C) Copyright 2014 3 * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de 4 * 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 #define CONFIG_E300 1 /* E300 family */ 16 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 17 #define CONFIG_MPC830x 1 /* MPC830x family */ 18 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 19 #define CONFIG_HRCON 1 /* HRCON board specific */ 20 21 #define CONFIG_SYS_TEXT_BASE 0xFE000000 22 23 #define CONFIG_BOARD_EARLY_INIT_F 24 #define CONFIG_BOARD_EARLY_INIT_R 25 #define CONFIG_LAST_STAGE_INIT 26 27 #define CONFIG_FSL_ESDHC 28 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 29 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111 30 31 #define CONFIG_GENERIC_MMC 32 #define CONFIG_DOS_PARTITION 33 34 #define CONFIG_CMD_FPGAD 35 #define CONFIG_CMD_IOLOOP 36 37 /* 38 * System Clock Setup 39 */ 40 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 41 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 42 43 /* 44 * Hardware Reset Configuration Word 45 * if CLKIN is 66.66MHz, then 46 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 47 * We choose the A type silicon as default, so the core is 400Mhz. 48 */ 49 #define CONFIG_SYS_HRCW_LOW (\ 50 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 51 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 52 HRCWL_SVCOD_DIV_2 |\ 53 HRCWL_CSB_TO_CLKIN_4X1 |\ 54 HRCWL_CORE_TO_CSB_3X1) 55 /* 56 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 57 * in 8308's HRCWH according to the manual, but original Freescale's 58 * code has them and I've expirienced some problems using the board 59 * with BDI3000 attached when I've tried to set these bits to zero 60 * (UART doesn't work after the 'reset run' command). 61 */ 62 #define CONFIG_SYS_HRCW_HIGH (\ 63 HRCWH_PCI_HOST |\ 64 HRCWH_PCI1_ARBITER_ENABLE |\ 65 HRCWH_CORE_ENABLE |\ 66 HRCWH_FROM_0XFFF00100 |\ 67 HRCWH_BOOTSEQ_DISABLE |\ 68 HRCWH_SW_WATCHDOG_DISABLE |\ 69 HRCWH_ROM_LOC_LOCAL_16BIT |\ 70 HRCWH_RL_EXT_LEGACY |\ 71 HRCWH_TSEC1M_IN_RGMII |\ 72 HRCWH_TSEC2M_IN_RGMII |\ 73 HRCWH_BIG_ENDIAN) 74 75 /* 76 * System IO Config 77 */ 78 #define CONFIG_SYS_SICRH (\ 79 SICRH_ESDHC_A_SD |\ 80 SICRH_ESDHC_B_SD |\ 81 SICRH_ESDHC_C_SD |\ 82 SICRH_GPIO_A_GPIO |\ 83 SICRH_GPIO_B_GPIO |\ 84 SICRH_IEEE1588_A_GPIO |\ 85 SICRH_USB |\ 86 SICRH_GTM_GPIO |\ 87 SICRH_IEEE1588_B_GPIO |\ 88 SICRH_ETSEC2_GPIO |\ 89 SICRH_GPIOSEL_1 |\ 90 SICRH_TMROBI_V3P3 |\ 91 SICRH_TSOBI1_V2P5 |\ 92 SICRH_TSOBI2_V2P5) /* 0x0037f103 */ 93 #define CONFIG_SYS_SICRL (\ 94 SICRL_SPI_PF0 |\ 95 SICRL_UART_PF0 |\ 96 SICRL_IRQ_PF0 |\ 97 SICRL_I2C2_PF0 |\ 98 SICRL_ETSEC1_GTX_CLK125) /* 0x00000000 */ 99 100 /* 101 * IMMR new address 102 */ 103 #define CONFIG_SYS_IMMR 0xE0000000 104 105 /* 106 * SERDES 107 */ 108 #define CONFIG_FSL_SERDES 109 #define CONFIG_FSL_SERDES1 0xe3000 110 111 /* 112 * Arbiter Setup 113 */ 114 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 115 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 116 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 117 118 /* 119 * DDR Setup 120 */ 121 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 122 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 123 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 124 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 125 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 126 | DDRCDR_PZ_LOZ \ 127 | DDRCDR_NZ_LOZ \ 128 | DDRCDR_ODT \ 129 | DDRCDR_Q_DRN) 130 /* 0x7b880001 */ 131 /* 132 * Manually set up DDR parameters 133 * consist of one chip NT5TU64M16HG from NANYA 134 */ 135 136 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 137 138 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 139 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 140 | CSCONFIG_ODT_RD_NEVER \ 141 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 142 | CSCONFIG_BANK_BIT_3 \ 143 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 144 /* 0x80010102 */ 145 #define CONFIG_SYS_DDR_TIMING_3 0 146 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 147 | (0 << TIMING_CFG0_WRT_SHIFT) \ 148 | (0 << TIMING_CFG0_RRT_SHIFT) \ 149 | (0 << TIMING_CFG0_WWT_SHIFT) \ 150 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 151 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 152 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 153 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 154 /* 0x00260802 */ 155 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 156 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 157 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 158 | (7 << TIMING_CFG1_CASLAT_SHIFT) \ 159 | (9 << TIMING_CFG1_REFREC_SHIFT) \ 160 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 161 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 162 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 163 /* 0x26279222 */ 164 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 165 | (4 << TIMING_CFG2_CPO_SHIFT) \ 166 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 167 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 168 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 169 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 170 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 171 /* 0x021848c5 */ 172 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \ 173 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 174 /* 0x08240100 */ 175 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 176 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 177 | SDRAM_CFG_DBW_16) 178 /* 0x43100000 */ 179 180 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 181 #define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ 182 | (0x0242 << SDRAM_MODE_SD_SHIFT)) 183 /* ODT 150ohm CL=4, AL=0 on SDRAM */ 184 #define CONFIG_SYS_DDR_MODE2 0x00000000 185 186 /* 187 * Memory test 188 */ 189 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 190 #define CONFIG_SYS_MEMTEST_END 0x07f00000 191 192 /* 193 * The reserved memory 194 */ 195 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 196 197 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 198 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 199 200 /* 201 * Initial RAM Base Address Setup 202 */ 203 #define CONFIG_SYS_INIT_RAM_LOCK 1 204 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 205 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 206 #define CONFIG_SYS_GBL_DATA_OFFSET \ 207 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 208 209 /* 210 * Local Bus Configuration & Clock Setup 211 */ 212 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 213 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 214 #define CONFIG_SYS_LBC_LBCR 0x00040000 215 216 /* 217 * FLASH on the Local Bus 218 */ 219 #if 1 220 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 221 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 222 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 223 #define CONFIG_FLASH_CFI_LEGACY 224 #define CONFIG_SYS_FLASH_LEGACY_512Kx16 225 #else 226 #define CONFIG_SYS_NO_FLASH 227 #endif 228 229 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 230 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is up to 8M */ 231 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 232 233 /* Window base at flash base */ 234 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 235 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 236 237 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 238 | BR_PS_16 /* 16 bit port */ \ 239 | BR_MS_GPCM /* MSEL = GPCM */ \ 240 | BR_V) /* valid */ 241 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 242 | OR_UPM_XAM \ 243 | OR_GPCM_CSNT \ 244 | OR_GPCM_ACS_DIV2 \ 245 | OR_GPCM_XACS \ 246 | OR_GPCM_SCY_15 \ 247 | OR_GPCM_TRLX_SET \ 248 | OR_GPCM_EHTR_SET) 249 250 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 251 #define CONFIG_SYS_MAX_FLASH_SECT 135 252 253 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 254 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 255 256 /* 257 * FPGA 258 */ 259 #define CONFIG_SYS_FPGA0_BASE 0xE0600000 260 #define CONFIG_SYS_FPGA0_SIZE 1 /* FPGA size is 1M */ 261 262 /* Window base at FPGA base */ 263 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA0_BASE 264 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_1MB) 265 266 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA0_BASE \ 267 | BR_PS_16 /* 16 bit port */ \ 268 | BR_MS_GPCM /* MSEL = GPCM */ \ 269 | BR_V) /* valid */ 270 #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \ 271 | OR_UPM_XAM \ 272 | OR_GPCM_CSNT \ 273 | OR_GPCM_ACS_DIV2 \ 274 | OR_GPCM_XACS \ 275 | OR_GPCM_SCY_15 \ 276 | OR_GPCM_TRLX_SET \ 277 | OR_GPCM_EHTR_SET) 278 279 #define CONFIG_SYS_FPGA_BASE(k) CONFIG_SYS_FPGA0_BASE 280 #define CONFIG_SYS_FPGA_DONE(k) 0x0010 281 282 #define CONFIG_SYS_FPGA_COUNT 1 283 284 #define CONFIG_SYS_MCLINK_MAX 3 285 286 #define CONFIG_SYS_FPGA_PTR \ 287 { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL } 288 289 /* 290 * Serial Port 291 */ 292 #define CONFIG_CONS_INDEX 2 293 #define CONFIG_SYS_NS16550_SERIAL 294 #define CONFIG_SYS_NS16550_REG_SIZE 1 295 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 296 297 #define CONFIG_SYS_BAUDRATE_TABLE \ 298 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 299 300 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 301 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 302 303 /* Pass open firmware flat tree */ 304 305 /* I2C */ 306 #define CONFIG_SYS_I2C 307 #define CONFIG_SYS_I2C_FSL 308 #define CONFIG_SYS_FSL_I2C_SPEED 400000 309 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 310 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 311 312 #define CONFIG_PCA953X /* NXP PCA9554 */ 313 #define CONFIG_PCA9698 /* NXP PCA9698 */ 314 315 #define CONFIG_SYS_I2C_IHS 316 #define CONFIG_SYS_I2C_IHS_CH0 317 #define CONFIG_SYS_I2C_IHS_SPEED_0 50000 318 #define CONFIG_SYS_I2C_IHS_SLAVE_0 0x7F 319 #define CONFIG_SYS_I2C_IHS_CH1 320 #define CONFIG_SYS_I2C_IHS_SPEED_1 50000 321 #define CONFIG_SYS_I2C_IHS_SLAVE_1 0x7F 322 #define CONFIG_SYS_I2C_IHS_CH2 323 #define CONFIG_SYS_I2C_IHS_SPEED_2 50000 324 #define CONFIG_SYS_I2C_IHS_SLAVE_2 0x7F 325 #define CONFIG_SYS_I2C_IHS_CH3 326 #define CONFIG_SYS_I2C_IHS_SPEED_3 50000 327 #define CONFIG_SYS_I2C_IHS_SLAVE_3 0x7F 328 329 #ifdef CONFIG_HRCON_DH 330 #define CONFIG_SYS_I2C_IHS_DUAL 331 #define CONFIG_SYS_I2C_IHS_CH0_1 332 #define CONFIG_SYS_I2C_IHS_SPEED_0_1 50000 333 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1 0x7F 334 #define CONFIG_SYS_I2C_IHS_CH1_1 335 #define CONFIG_SYS_I2C_IHS_SPEED_1_1 50000 336 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1 0x7F 337 #define CONFIG_SYS_I2C_IHS_CH2_1 338 #define CONFIG_SYS_I2C_IHS_SPEED_2_1 50000 339 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1 0x7F 340 #define CONFIG_SYS_I2C_IHS_CH3_1 341 #define CONFIG_SYS_I2C_IHS_SPEED_3_1 50000 342 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1 0x7F 343 #endif 344 345 /* 346 * Software (bit-bang) I2C driver configuration 347 */ 348 #define CONFIG_SYS_I2C_SOFT 349 #define CONFIG_SYS_I2C_SOFT_SPEED 50000 350 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 351 #define I2C_SOFT_DECLARATIONS2 352 #define CONFIG_SYS_I2C_SOFT_SPEED_2 50000 353 #define CONFIG_SYS_I2C_SOFT_SLAVE_2 0x7F 354 #define I2C_SOFT_DECLARATIONS3 355 #define CONFIG_SYS_I2C_SOFT_SPEED_3 50000 356 #define CONFIG_SYS_I2C_SOFT_SLAVE_3 0x7F 357 #define I2C_SOFT_DECLARATIONS4 358 #define CONFIG_SYS_I2C_SOFT_SPEED_4 50000 359 #define CONFIG_SYS_I2C_SOFT_SLAVE_4 0x7F 360 #define I2C_SOFT_DECLARATIONS5 361 #define CONFIG_SYS_I2C_SOFT_SPEED_5 50000 362 #define CONFIG_SYS_I2C_SOFT_SLAVE_5 0x7F 363 #define I2C_SOFT_DECLARATIONS6 364 #define CONFIG_SYS_I2C_SOFT_SPEED_6 50000 365 #define CONFIG_SYS_I2C_SOFT_SLAVE_6 0x7F 366 #define I2C_SOFT_DECLARATIONS7 367 #define CONFIG_SYS_I2C_SOFT_SPEED_7 50000 368 #define CONFIG_SYS_I2C_SOFT_SLAVE_7 0x7F 369 #define I2C_SOFT_DECLARATIONS8 370 #define CONFIG_SYS_I2C_SOFT_SPEED_8 50000 371 #define CONFIG_SYS_I2C_SOFT_SLAVE_8 0x7F 372 373 #ifdef CONFIG_HRCON_DH 374 #define I2C_SOFT_DECLARATIONS9 375 #define CONFIG_SYS_I2C_SOFT_SPEED_9 50000 376 #define CONFIG_SYS_I2C_SOFT_SLAVE_9 0x7F 377 #define I2C_SOFT_DECLARATIONS10 378 #define CONFIG_SYS_I2C_SOFT_SPEED_10 50000 379 #define CONFIG_SYS_I2C_SOFT_SLAVE_10 0x7F 380 #define I2C_SOFT_DECLARATIONS11 381 #define CONFIG_SYS_I2C_SOFT_SPEED_11 50000 382 #define CONFIG_SYS_I2C_SOFT_SLAVE_11 0x7F 383 #define I2C_SOFT_DECLARATIONS12 384 #define CONFIG_SYS_I2C_SOFT_SPEED_12 50000 385 #define CONFIG_SYS_I2C_SOFT_SLAVE_12 0x7F 386 #endif 387 388 #ifdef CONFIG_HRCON_DH 389 #define CONFIG_SYS_ICS8N3QV01_I2C {13, 14, 15, 16, 17, 18, 19, 20} 390 #define CONFIG_SYS_DP501_I2C {1, 3, 5, 7, 2, 4, 6, 8} 391 #define CONFIG_HRCON_FANS { {10, 0x4c}, {11, 0x4c}, \ 392 {12, 0x4c} } 393 #else 394 #define CONFIG_SYS_ICS8N3QV01_I2C {9, 10, 11, 12} 395 #define CONFIG_SYS_DP501_I2C {1, 2, 3, 4} 396 #define CONFIG_HRCON_FANS { {6, 0x4c}, {7, 0x4c}, \ 397 {8, 0x4c} } 398 #endif 399 400 #ifndef __ASSEMBLY__ 401 void fpga_gpio_set(unsigned int bus, int pin); 402 void fpga_gpio_clear(unsigned int bus, int pin); 403 int fpga_gpio_get(unsigned int bus, int pin); 404 void fpga_control_set(unsigned int bus, int pin); 405 void fpga_control_clear(unsigned int bus, int pin); 406 #endif 407 408 #define I2C_SDA_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200) 409 #define I2C_SCL_GPIO ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100) 410 #define I2C_FPGA_IDX (I2C_ADAP_HWNR % 4) 411 412 #ifdef CONFIG_HRCON_DH 413 #define I2C_ACTIVE \ 414 do { \ 415 if (I2C_ADAP_HWNR > 7) \ 416 fpga_control_set(I2C_FPGA_IDX, 0x0004); \ 417 else \ 418 fpga_control_clear(I2C_FPGA_IDX, 0x0004); \ 419 } while (0) 420 #else 421 #define I2C_ACTIVE { } 422 #endif 423 #define I2C_TRISTATE { } 424 #define I2C_READ \ 425 (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0) 426 #define I2C_SDA(bit) \ 427 do { \ 428 if (bit) \ 429 fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 430 else \ 431 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \ 432 } while (0) 433 #define I2C_SCL(bit) \ 434 do { \ 435 if (bit) \ 436 fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 437 else \ 438 fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \ 439 } while (0) 440 #define I2C_DELAY udelay(25) /* 1/4 I2C clock duration */ 441 442 /* 443 * Software (bit-bang) MII driver configuration 444 */ 445 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 446 #define CONFIG_BITBANGMII_MULTI 447 448 /* 449 * OSD Setup 450 */ 451 #define CONFIG_SYS_OSD_SCREENS 1 452 #define CONFIG_SYS_DP501_DIFFERENTIAL 453 #define CONFIG_SYS_DP501_VCAPCTRL0 0x01 /* DDR mode 0, DE for H/VSYNC */ 454 455 #ifdef CONFIG_HRCON_DH 456 #define CONFIG_SYS_OSD_DH 457 #endif 458 459 /* 460 * General PCI 461 * Addresses are mapped 1-1. 462 */ 463 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 464 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 465 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 466 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 467 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 468 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 469 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 470 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 471 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 472 473 /* enable PCIE clock */ 474 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 475 476 #define CONFIG_PCI_INDIRECT_BRIDGE 477 #define CONFIG_PCIE 478 479 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 480 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 481 482 /* 483 * TSEC 484 */ 485 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 486 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 487 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 488 489 /* 490 * TSEC ethernet configuration 491 */ 492 #define CONFIG_MII 1 /* MII PHY management */ 493 #define CONFIG_TSEC1 494 #define CONFIG_TSEC1_NAME "eTSEC0" 495 #define TSEC1_PHY_ADDR 1 496 #define TSEC1_PHYIDX 0 497 #define TSEC1_FLAGS TSEC_GIGABIT 498 499 /* Options are: eTSEC[0-1] */ 500 #define CONFIG_ETHPRIME "eTSEC0" 501 502 /* 503 * Environment 504 */ 505 #if 1 506 #define CONFIG_ENV_IS_IN_FLASH 1 507 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 508 CONFIG_SYS_MONITOR_LEN) 509 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 510 #define CONFIG_ENV_SIZE 0x2000 511 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 512 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 513 #else 514 #define CONFIG_ENV_IS_NOWHERE 515 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 516 #endif 517 518 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 519 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 520 521 /* 522 * Command line configuration. 523 */ 524 #define CONFIG_CMD_PCI 525 526 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 527 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 528 529 /* 530 * Miscellaneous configurable options 531 */ 532 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 533 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 534 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 535 536 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 537 538 /* Print Buffer Size */ 539 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 540 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 541 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 542 543 /* 544 * For booting Linux, the board info and command line data 545 * have to be in the first 256 MB of memory, since this is 546 * the maximum mapped by the Linux kernel during initialization. 547 */ 548 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 549 550 /* 551 * Core HID Setup 552 */ 553 #define CONFIG_SYS_HID0_INIT 0x000000000 554 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 555 HID0_ENABLE_INSTRUCTION_CACHE | \ 556 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 557 #define CONFIG_SYS_HID2 HID2_HBE 558 559 /* 560 * MMU Setup 561 */ 562 563 /* DDR: cache cacheable */ 564 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 565 BATL_MEMCOHERENCE) 566 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 567 BATU_VS | BATU_VP) 568 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 569 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 570 571 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */ 572 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 573 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 574 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 575 BATU_VP) 576 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 577 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 578 579 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 580 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 581 BATL_MEMCOHERENCE) 582 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 583 BATU_VS | BATU_VP) 584 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ 585 BATL_CACHEINHIBIT | \ 586 BATL_GUARDEDSTORAGE) 587 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 588 589 /* Stack in dcache: cacheable, no memory coherence */ 590 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 591 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 592 BATU_VS | BATU_VP) 593 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 594 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 595 596 /* 597 * Environment Configuration 598 */ 599 600 #define CONFIG_ENV_OVERWRITE 601 602 #if defined(CONFIG_TSEC_ENET) 603 #define CONFIG_HAS_ETH0 604 #endif 605 606 #define CONFIG_BAUDRATE 115200 607 608 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 609 610 611 #define CONFIG_HOSTNAME hrcon 612 #define CONFIG_ROOTPATH "/opt/nfsroot" 613 #define CONFIG_BOOTFILE "uImage" 614 615 #define CONFIG_PREBOOT /* enable preboot variable */ 616 617 #define CONFIG_EXTRA_ENV_SETTINGS \ 618 "netdev=eth0\0" \ 619 "consoledev=ttyS1\0" \ 620 "u-boot=u-boot.bin\0" \ 621 "kernel_addr=1000000\0" \ 622 "fdt_addr=C00000\0" \ 623 "fdtfile=hrcon.dtb\0" \ 624 "load=tftp ${loadaddr} ${u-boot}\0" \ 625 "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \ 626 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\ 627 " +${filesize};cp.b ${fileaddr} " \ 628 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 629 "upd=run load update\0" \ 630 631 #define CONFIG_NFSBOOTCOMMAND \ 632 "setenv bootargs root=/dev/nfs rw " \ 633 "nfsroot=$serverip:$rootpath " \ 634 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 635 "console=$consoledev,$baudrate $othbootargs;" \ 636 "tftp ${kernel_addr} $bootfile;" \ 637 "tftp ${fdt_addr} $fdtfile;" \ 638 "bootm ${kernel_addr} - ${fdt_addr}" 639 640 #define CONFIG_MMCBOOTCOMMAND \ 641 "setenv bootargs root=/dev/mmcblk0p3 rw rootwait " \ 642 "console=$consoledev,$baudrate $othbootargs;" \ 643 "ext2load mmc 0:2 ${kernel_addr} $bootfile;" \ 644 "ext2load mmc 0:2 ${fdt_addr} $fdtfile;" \ 645 "bootm ${kernel_addr} - ${fdt_addr}" 646 647 #define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND 648 649 #endif /* __CONFIG_H */ 650