1 /* 2 * (C) Copyright 2015 Linaro 3 * 4 * Peter Griffin <peter.griffin@linaro.org> 5 * 6 * Configuration for HiKey 96boards CE. Parts were derived from other ARM 7 * configurations. 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #ifndef __HIKEY_H 13 #define __HIKEY_H 14 15 #include <linux/sizes.h> 16 17 #define CONFIG_POWER 18 #define CONFIG_POWER_HI6553 19 20 #define CONFIG_REMAKE_ELF 21 22 #define CONFIG_SUPPORT_RAW_INITRD 23 24 /* Physical Memory Map */ 25 26 /* CONFIG_SYS_TEXT_BASE needs to align with where ATF loads bl33.bin */ 27 #define CONFIG_SYS_TEXT_BASE 0x35000000 28 29 #define CONFIG_NR_DRAM_BANKS 6 30 #define PHYS_SDRAM_1 0x00000000 31 32 /* 1008 MB (the last 16Mb are secured for TrustZone by ATF*/ 33 #define PHYS_SDRAM_1_SIZE 0x3EFFFFFF 34 35 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 36 37 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 38 39 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) 40 41 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000) 42 43 /* Generic Timer Definitions */ 44 #define COUNTER_FREQUENCY 19000000 45 46 /* Generic Interrupt Controller Definitions */ 47 #define GICD_BASE 0xf6801000 48 #define GICC_BASE 0xf6802000 49 50 /* Size of malloc() pool */ 51 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M) 52 53 /* Serial port PL010/PL011 through the device model */ 54 #define CONFIG_PL01X_SERIAL 55 56 #ifdef CONFIG_CMD_USB 57 #define CONFIG_USB_DWC2 58 #define CONFIG_USB_DWC2_REG_ADDR 0xF72C0000 59 /*#define CONFIG_DWC2_DFLT_SPEED_FULL*/ 60 #define CONFIG_DWC2_ENABLE_DYNAMIC_FIFO 61 62 #define CONFIG_USB_HOST_ETHER 63 #define CONFIG_USB_ETHER_SMSC95XX 64 #define CONFIG_USB_ETHER_ASIX 65 #define CONFIG_MISC_INIT_R 66 #endif 67 68 #define CONFIG_HIKEY_GPIO 69 70 /* SD/MMC configuration */ 71 #define CONFIG_BOUNCE_BUFFER 72 73 #define CONFIG_FS_EXT4 74 75 /* Command line configuration */ 76 #define CONFIG_CMD_ENV 77 78 #define CONFIG_MTD_PARTITIONS 79 80 /* BOOTP options */ 81 #define CONFIG_BOOTP_BOOTFILESIZE 82 83 #include <config_distro_defaults.h> 84 85 /* Initial environment variables */ 86 87 /* 88 * Defines where the kernel and FDT will be put in RAM 89 */ 90 91 /* Assume we boot with root on the seventh partition of eMMC */ 92 #define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 root=/dev/mmcblk0p9 rw" 93 94 #define BOOT_TARGET_DEVICES(func) \ 95 func(USB, usb, 0) \ 96 func(MMC, mmc, 1) \ 97 func(DHCP, dhcp, na) 98 #include <config_distro_bootcmd.h> 99 100 #define CONFIG_EXTRA_ENV_SETTINGS \ 101 "kernel_name=Image\0" \ 102 "kernel_addr_r=0x00080000\0" \ 103 "fdtfile=hi6220-hikey.dtb\0" \ 104 "fdt_addr_r=0x02000000\0" \ 105 "fdt_high=0xffffffffffffffff\0" \ 106 "initrd_high=0xffffffffffffffff\0" \ 107 BOOTENV 108 109 /* Preserve environment on sd card */ 110 #define CONFIG_ENV_SIZE 0x1000 111 #define CONFIG_ENV_IS_IN_FAT 112 #define FAT_ENV_INTERFACE "mmc" 113 #define FAT_ENV_DEVICE_AND_PART "1:1" 114 #define FAT_ENV_FILE "uboot.env" 115 #define CONFIG_FAT_WRITE 116 #define CONFIG_ENV_VARS_UBOOT_CONFIG 117 118 /* Monitor Command Prompt */ 119 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 120 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 121 sizeof(CONFIG_SYS_PROMPT) + 16) 122 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 123 #define CONFIG_SYS_LONGHELP 124 #define CONFIG_CMDLINE_EDITING 125 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 126 127 #endif /* __HIKEY_H */ 128