1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * (C) Copyright 2011 4 * egnite GmbH <info@egnite.de> 5 * 6 * Configuation settings for Ethernut 5 with AT91SAM9XE. 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #include <asm/hardware.h> 13 14 /* The first stage boot loader expects u-boot running at this address. */ 15 16 /* The first stage boot loader takes care of low level initialization. */ 17 #define CONFIG_SKIP_LOWLEVEL_INIT 18 19 /* Set our official architecture number. */ 20 #define CONFIG_MACH_TYPE MACH_TYPE_ETHERNUT5 21 22 /* CPU information */ 23 #define CONFIG_ARCH_CPU_INIT 24 25 /* ARM asynchronous clock */ 26 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ 27 #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */ 28 29 /* 32kB internal SRAM */ 30 #define CONFIG_SRAM_BASE 0x00300000 /*AT91SAM9XE_SRAM_BASE */ 31 #define CONFIG_SRAM_SIZE (32 << 10) 32 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SRAM_BASE + CONFIG_SRAM_SIZE - \ 33 GENERATED_GBL_DATA_SIZE) 34 35 /* 128MB SDRAM in 1 bank */ 36 #define CONFIG_SYS_SDRAM_BASE 0x20000000 37 #define CONFIG_SYS_SDRAM_SIZE (128 << 20) 38 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE 39 #define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR 40 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (1 << 20)) 41 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 42 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE \ 43 - CONFIG_SYS_MALLOC_LEN) 44 45 /* 512kB on-chip NOR flash */ 46 # define CONFIG_SYS_MAX_FLASH_BANKS 1 47 # define CONFIG_SYS_FLASH_BASE 0x00200000 /* AT91SAM9XE_FLASH_BASE */ 48 # define CONFIG_AT91_EFLASH 49 # define CONFIG_SYS_MAX_FLASH_SECT 32 50 # define CONFIG_EFLASH_PROTSECTORS 1 51 52 53 /* bootstrap + u-boot + env + linux in dataflash on CS0 */ 54 #define CONFIG_ENV_OFFSET 0x3DE000 55 #define CONFIG_ENV_SIZE (132 << 10) 56 #define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE 57 58 /* NAND flash */ 59 #ifdef CONFIG_CMD_NAND 60 #define CONFIG_SYS_MAX_NAND_DEVICE 1 61 #define CONFIG_SYS_NAND_BASE 0x40000000 62 #define CONFIG_SYS_NAND_DBW_8 63 /* our ALE is AD21 */ 64 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 65 /* our CLE is AD22 */ 66 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 67 #define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) 68 #endif 69 70 /* JFFS2 */ 71 #ifdef CONFIG_CMD_JFFS2 72 #define CONFIG_JFFS2_CMDLINE 73 #define CONFIG_JFFS2_NAND 74 #endif 75 76 /* Ethernet */ 77 #define CONFIG_NET_RETRY_COUNT 20 78 #define CONFIG_MACB 79 #define CONFIG_RMII 80 #define CONFIG_PHY_ID 0 81 #define CONFIG_MACB_SEARCH_PHY 82 83 /* MMC */ 84 #ifdef CONFIG_CMD_MMC 85 #define CONFIG_GENERIC_ATMEL_MCI 86 #define CONFIG_SYS_MMC_CD_PIN AT91_PIO_PORTC, 8 87 #endif 88 89 /* USB */ 90 #ifdef CONFIG_CMD_USB 91 #define CONFIG_USB_ATMEL 92 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 93 #define CONFIG_USB_OHCI_NEW 94 #define CONFIG_SYS_USB_OHCI_CPU_INIT 95 #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 96 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "host" 97 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 98 #endif 99 100 /* RTC */ 101 #if defined(CONFIG_CMD_DATE) || defined(CONFIG_CMD_SNTP) 102 #define CONFIG_RTC_PCF8563 103 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 104 #endif 105 106 /* I2C */ 107 #define CONFIG_SYS_MAX_I2C_BUS 1 108 109 #define CONFIG_SYS_I2C 110 #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ 111 #define CONFIG_SYS_I2C_SOFT_SPEED 100000 112 #define CONFIG_SYS_I2C_SOFT_SLAVE 0 113 114 #define I2C_SOFT_DECLARATIONS 115 116 #define GPIO_I2C_SCL AT91_PIO_PORTA, 24 117 #define GPIO_I2C_SDA AT91_PIO_PORTA, 23 118 119 #define I2C_INIT { \ 120 at91_set_pio_periph(AT91_PIO_PORTA, 23, 0); \ 121 at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ 122 at91_set_pio_periph(AT91_PIO_PORTA, 24, 0); \ 123 at91_set_pio_output(AT91_PIO_PORTA, 24, 0); \ 124 at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ 125 } 126 127 #define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTA, 23, 0) 128 #define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTA, 23, 0) 129 #define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) 130 #define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTA, 23, bit) 131 #define I2C_DELAY udelay(100) 132 #define I2C_READ at91_get_pio_value(AT91_PIO_PORTA, 23) 133 134 /* DHCP/BOOTP options */ 135 #ifdef CONFIG_CMD_DHCP 136 #define CONFIG_BOOTP_BOOTFILESIZE 137 #define CONFIG_SYS_AUTOLOAD "n" 138 #endif 139 140 /* File systems */ 141 142 /* Boot command */ 143 #define CONFIG_CMDLINE_TAG 144 #define CONFIG_SETUP_MEMORY_TAGS 145 #define CONFIG_INITRD_TAG 146 #define CONFIG_BOOTCOMMAND "sf probe 0:0; " \ 147 "sf read 0x22000000 0xc6000 0x294000; " \ 148 "bootm 0x22000000" 149 150 /* Misc. u-boot settings */ 151 152 #endif 153